When I ordered my KX3 in December of 2019, the only things I ordered from Elecraft were the KX3, the KXAT3, and the KXPKT cable kit and a second power cable. I added the SideKX end plates and lexan cover and the cover for the KXPD3 port. I mainly do digital modes when I’m portable so I’ve got the radio connected to power (Either a 7.5Ah SLAB, I’ve had it forever; or the battery in the car.)
Bare minimum for me to carry for a POTA activation is the cable bundle to the Raspberry Pi, the Pi, and power cables. I do log on paper, but nothing special about that, any paper will do as long as you copy the right info. I’m working on learning CW and will probably buy a small set of paddles and hook them to the key jack on the side of the radio. Every other port over there is in use, might as well use that one too. Jocelyn. On Mon, May 2, 2022 at 19:19 Gwen Patton <ard...@gmail.com> wrote: > I have a KX3 with the KXAT3, KXBC3, KXFL3, and KXPA100. I put the SideKX > side panels on it, and got the SideKX RAM mount adapters for the radio and > the panadapter. I took the batteries out of the KXBC3 after they kept me > from doing a firmware update properly. If you run into a problem with the > update, the solution is to shut down all power to the radio so it'll reset > -- but the internal batteries will keep it from doing this. To properly > shut it all the way down, you have to remove the batteries. Well, I'd > forgotten about that, and was pulling my hair, thinking I'd bricked the > poor thing! When I figured it out, I was so relieved, I had to sit down and > have a relief cry. > > It's a wonderful radio, so much so, I'm reluctant to use it in the field, > for fear a dog will pee on it, or a meteor will slam into it, or something > else that'll break it. When I need something similar in function, I'll use > my IQ32, because frankly, I care a lot less if it gets broken or stolen. > Others may not have my concerns, though, and might be able to rationalize > taking the KX3 into the field on a regular basis, perhaps as a YOLO issue. > I love my KX3 far too much to risk it unnecessarily! > > I don't use the Elecraft paddles, though. I do have the minimalist kit from > QRP Guys that will screw onto that port, but I don't like using it. > Instead, I built a little box that lets me plug in two mechanical keys and > two paddles, running the mechanical keys (Cootie, bug, straight key, etc.) > through the 2x2 header meant for the Elecraft paddle. I even use the same > thumbscrews to hold the box to the bottom of the rig. It's very convenient, > and if, say, I want to switch my W1SFR Torsion Bar Cootie Paddle from > paddle to cootie mode, I just move the plug on its cable to one of the > mechanical key jacks on the box instead of one of the paddle jacks, and > it's instantly in cootie mode. I keep meaning to write something up about > that box, but I keep forgetting. > > If you get a KX3, you'll love it. I bought it and the PX3, then two weeks > later I ordered the KXPA100. I ordered the Powerwerx power supply that was > recommended at the time, and it works beautifully. > > -=-=-=-=-=-=-=-=- > 73, > Gwen, NG3P > > > On Mon, May 2, 2022 at 2:16 PM Julia Tuttle <ju...@juliatuttle.net> wrote: > > > Hey Glen, > > > > Here's my take on KX3 options and such: > > > > KXAT3 is absolutely worth it. It will tune *anything* and is super easy > to > > use. (Looking at you, Icom, where pushing the button turns the tuner on > and > > off and you have to hold it to run a tuning cycle.) > > > > KXBC3 is okay. I use the NiMHs more like a backup, for things like moving > > the radio around while it's on or temporarily unplugging the power supply > > to avoid some RFI. If you actually want to operate off battery seriously, > > I'd get an external lithium ion battery from Bioenno. > > > > (Do not trust the RTC in the KXBC3; it has been terribly inaccurate in my > > experience, and even a $10 wristwatch would do better. You might get some > > use out of it if you make sure to set it every time you sat down to > operate > > and you really don't want a separate clock.) > > > > I don't have the KX3-2M, but I wouldn't consider it myself based on the > low > > power output. If you want to do specialized VHF work, and you're willing > to > > throw an external amp at it, you might want it. > > > > I don't have the KXFL3, but I'm a casual enough operator that I'm not > sure > > I'd be able to speak to the benefits anyway. > > > > Not options in the same sense, but some other Elecraft accessories: > > > > KXPD3 is great. It doesn't hold a candle to external paddles made by > > companies that specialize in them, but it is unbeatable in compactness > and > > convenience. > > > > PX3 is good. It's integrated with the KX3 well, and if you've used and > > liked a panadapter before, this will make you happy. My only nit is that > > the hardware integration is cluttered (power to both the KX3 and PX3, > ACC1 > > serial between the two, and RX I/Q signals between the two). > > > > I don't have the KXPA100, but I've heard it's also integrated well and > is a > > solid amp. Big downside is the price; last I checked, you can spend about > > half as much and get the same functionality if you don't need the right > > Integration. Nonetheless, if I did want a 100W amp for my KX3, I'd > splurge > > and get it. > > > > And some third party accessories: > > > > SideKX side panels (and cover) from GEMS Products are, in my opinion, > > mandatory. I am much comfier throwing my KX3 in a backpack with them. > They > > do make the front panel slightly more cramped, but it's worth it to me. > > > > PAE-KX32 heatsink from Pro Audio Engineering is, as Eric said, great if > you > > want to run the KX3 at full power out and 100% duty cycle for digital > > modes. Not necessary, but makes a noticeable improvement, especially if > you > > point a small fan at it. > > > > PAE-KX33 power supply from PAE works, packs much smaller than a desktop > > power supply, and hasn't caused any RFI problems for me. Worth it if > you're > > going to be travelling to places with mains power but no existing shack > > power supply to borrow. > > > > Hope the wall of text helps! Questions welcome if you've got any. > > > > 73, > > > > Julie > > > > On Mon, May 2, 2022, 12:48 Eric Garner <garn...@gmail.com> wrote: > > > > > I have a KX3 fully loaded (KXFL3, KXAT3, KXBC3, KX3-2M) the only one I > > > would skip if I had to do it over is the KXBC3. The NiMH batteries just > > > don't have the oomph to justify adding them for me and having the RTC > > > doesn't really matter to me, your needs might be different. I just use > an > > > external LiFePO4 pack for power. > > > The Pro Audio Engineering heatsink addon ( > > > > https://proaudioeng.com/oos-pae-kx32-ultimate-heatsink-kit-elecraft-kx3/ > > ) > > > is nice if you will be running digimodes without an external amplifier. > > > > > > Eric KI7LTT > > > > > > On Mon, May 2, 2022 at 9:31 AM Glen Reid <greid...@gmail.com> wrote: > > > > > > > I am contemplating the purchase of a KX3. Looking for input from > users > > > on > > > > which options I should consider. > > > > Thanks es 73 > > > > gr > > > > K5FX > > > > ______________________________________________________________ > > > > Elecraft mailing list > > > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > > > Help: http://mailman.qth.net/mmfaq.htm > > > > Post: mailto:Elecraft@mailman.qth.net > > > > > > > > This list hosted by: http://www.qsl.net > > > > Please help support this email list: http://www.qsl.net/donate.html > > > > Message delivered to garn...@gmail.com > > > > > > > > > > > > > -- > > > --Eric > > > _________________________________________ > > > Eric Garner > > > ______________________________________________________________ > > > Elecraft mailing list > > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > > Help: http://mailman.qth.net/mmfaq.htm > > > Post: mailto:Elecraft@mailman.qth.net > > > > > > This list hosted by: http://www.qsl.net > > > Please help support this email list: http://www.qsl.net/donate.html > > > Message delivered to ju...@juliatuttle.net > > > > > ______________________________________________________________ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:Elecraft@mailman.qth.net > > > > This list hosted by: http://www.qsl.net > > Please help support this email list: http://www.qsl.net/donate.html > > Message delivered to ard...@gmail.com > > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to ae8jg.go...@gmail.com > -- 72, Jocelyn Gould AE8JG EM89mo KX3 # 11234 NAQCC # 7704 OMISS # 9948 4sqrp # 990 FP # 3579 ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
