-------- Original Message --------
Subject: Re: [Elecraft] K2 - How good on SSB?
Date: Fri, 16 Mar 2007 12:05:31 -0500
From: RC kc5wa <[EMAIL PROTECTED]>
To: Curt Milton <[EMAIL PROTECTED]>
References: <[EMAIL PROTECTED]>
Curt
Using my K2 #4948 @ qrp ssb 9watts I worked 42 of 50
states on 80/75 meters. The microphone used was 600 ohm
impedance RS Highball II. Antennas used an 5btv and
dipole at 12' bent around an urban lot. Difficult but
doable. YMMV
RC kc5wa
Curt Milton wrote:
Very interesting question. When sunspots were good, i never hesitated even on 20m (unless there was a huge pile-up) to speak into the mic of my QRP K2. It rewarded me with lots of QSOs (using a vertical antenna).
Recently I decided to check out its IF filtering across busy bands in the ARRL DX SSB contest. The narrower settings on the main board filter did do a good job of reducing QRM, as it improved with each toggle from 2 to 1.8 to 1.6 settings.
Things I don't know are:
(1) How well the K2 shape factors of the main board filter compare to typical 1.8 kHz accessory filters in higher end rigs. Note these typically have a wide ~ 2.4 kHz or wider stock filter and a single selectable narrow filter.
(2) How well the K2 speech processor works in comparison to other rigs.
I have no reason to discern any limitations for these - i just don't have any information other than casual use.
At one time I thought that not having passband tuning (IF shift) was a 'big limitation.' But now I realize its only a big factor on SSB when your filters is wider than needed (as is on many lower end HF rigs). Some folk have set their SSB filter up to be a quasi-IF shift by having one oriented down and one oriented up on say a 1.8 kHz BW -- but I can't say this is the best use of the 4 available settings.
(Gee - I know the enterprise would appreciate you buying a second K2, but you can only do one mode at once. No reason why your existing K2 can't be a CW QRP machine, a SSB machine, and by flipping the lid also a 100w multimode rig. )
73, curt
----- Original Message ----
From: Fred (FL) <[EMAIL PROTECTED]>
To: elecraft@mailman.qth.net
Sent: Friday, March 16, 2007 11:35:05 AM
Subject: [Elecraft] K2 - How good on SSB?
Thinking about building my 2nd K2. First # 54xx,
was a very sucessful build.
Does anyone have thoughts on how well the K2,
operates, by itself, as a SSB HF rig? It would
seem 15W is kind of pushing it for a suitable
signal - but just wondered if any successful
K2 SSB ops are around.
And I've always had this belief that 15W is not
enough to drive many or any amps?
Thanks,
Fred, N3CSY
____________________________________________________________________________________
No need to miss a message. Get email on-the-go
with Yahoo! Mail for Mobile. Get started.
http://mobile.yahoo.com/mail
_______________________________________________
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
____________________________________________________________________________________
Get your own web address.
Have a HUGE year through Yahoo! Small Business.
http://smallbusiness.yahoo.com/domains/?p=BESTDEAL
_______________________________________________
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
_______________________________________________
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
