Actually, I think RF output delay was introduced in MCU 1.87 / DSP 1.69, controlled by CONFIG:TX DLY (8-20ms).
Bob NW8L On Sun, Jun 8, 2008 at 7:31 PM, Don Wilhelm <[EMAIL PROTECTED]> wrote: > Lexa, > > I believe you are mis-interpreting What QSK DELAY does. It does *not* > increase the time before the onset of RF, but it does change the delay after > a keyup condition. > > The purpose of QSK DELAY is to keep the amplifier relays held in between > code elements so one does not have to listen to the loud clacking of the > amplifier relays. > > The delay of RF output after keydown is currently fixed in the K3, but there > is consideration being given to allow it to be user controlled in the > future. The adjustment range may be limited, so if you have transverters > and preamplifiers that must have a longer delay to the onset of RF, the TX > INH input would be required. > > 73, > Don W3FPR > Alexandr Kobranov wrote: >> >> Hello Mike, >> >> thanks to this "problem" I am totally confused now.... :-( >> >> Mentioned problem is maybe permanent in all previous versions, tried 1.88 >> now and have the same results. >> If SSB+CW active there is all the time RF out in SSB mode even if CW mode >> is in PTT or VOX. The difference is that if CW is in VOX/QSK then DELAY is >> applied, if CW in PTT it is like FULL QSK >> >> But IMHO if SSB mode is set to PTT and also CW mode is set to PTT there >> should be NO CW RF on output without any other conditions except PTT or XMIT >> or CW VOX/QSK active.(in SSB+CW) >> Am I right? Or am I so rigid? >> Aditonally to ensure application of CW VOX/QSK delay it (CW in SSB mode) >> should be only when CW mode in VOX/QSK. >> >> How it is possible I was fixed so long with this idea that SSB+CW is not >> working without CW mode in VOX/QSK? Maybe before 1.88 it was? >> SSB+CW was at 1.87 release - I have not a copy of it :-( >> >> Sorry for used bandwidth caused by my stupidity :-) >> 73! >> Lexa ok1dst >> >> >> >> Alexandr Kobranov napsal(a): >>> >>> Mike, >>> you are right... >>> When you have SSB + CW active (menu:CW WGHT press "1") there is now no >>> conncetion between PTT/VOX mode for CW and CW sending in SSB mode. >>> (as it was in previous versions as I remember) >>> My previous messages concerning this was based on previous experience and >>> only very short test with 2.02. Sorry. >>> >>> It is surely bug in this beta version as NO CW QSK DELAY is applied, only >>> RF based on Key is emitted. >>> >>> The correct function is to use CW VOX/QSK setting incl. VOX CW DELAY >>> which is now ignored. >>> >>> To avoid CW RF ins SSB or (CW keying without QSK delay) set SSB-CW until >>> influence of CW PTT/VOX/QSK setting will be back. Simply do not use Auto-CW >>> in beta 2.02 or go back with F/W. >>> >>> 73! >>> L. -dst- >>> >>> >>> Mike Harris napsal(a): >>>> >>>> Hi, >>>> >>>> Unless I'm misunderstanding something it works here. >>>> >>>> SSB - PTT mode, press paddle whilst in RX results in CW with RF output. >>>> Interestingly this happens even if true CW mode is not set to VOX. >>>> >>>> Is this somehow broken in v2.02? I haven't bothered to load it yet >>>> because it doesn't offer me anything I currently need and I will let the >>>> army of beta testers thrash it a bit. >>>> >>>> Regards, >>>> >>>> Mike VP8NO >>>> ----- Original Message ----- From: "Ken Kopp" <[EMAIL PROTECTED]> >>>> To: <elecraft@mailman.qth.net> >>>> Sent: Saturday, June 07, 2008 10:38 PM >>>> Subject: [Elecraft] cw/vox/PTT w/ ver 1.96/1.73 >>>> >>>> >>>> | Same here ... no CW TX if in SSB / PTT mode. I use a foot >>>> | switch for PTT on SSB and VOX on CW. >>>> | >>>> | 73! Ken Kopp - K0PP >>>> >>>> _______________________________________________ >>>> Elecraft mailing list >>>> Post to: Elecraft@mailman.qth.net >>>> You must be a subscriber to post to the list. >>>> Subscriber Info (Addr. Change, sub, unsub etc.): >>>> http://mailman.qth.net/mailman/listinfo/elecraft Help: >>>> http://mailman.qth.net/subscribers.htm >>>> Elecraft web page: http://www.elecraft.com >>>> >>> _______________________________________________ >>> Elecraft mailing list >>> Post to: Elecraft@mailman.qth.net >>> You must be a subscriber to post to the list. >>> Subscriber Info (Addr. Change, sub, unsub etc.): >>> http://mailman.qth.net/mailman/listinfo/elecraft Help: >>> http://mailman.qth.net/subscribers.htm >>> Elecraft web page: http://www.elecraft.com >>> >> _______________________________________________ >> Elecraft mailing list >> Post to: Elecraft@mailman.qth.net >> You must be a subscriber to post to the list. >> Subscriber Info (Addr. Change, sub, unsub etc.): >> http://mailman.qth.net/mailman/listinfo/elecraft Help: >> http://mailman.qth.net/subscribers.htm >> Elecraft web page: http://www.elecraft.com >> ------------------------------------------------------------------------ >> >> >> No virus found in this incoming message. >> Checked by AVG. Version: 8.0.100 / Virus Database: 270.0.0/1489 - Release >> Date: 6/7/2008 11:17 AM >> > > _______________________________________________ > Elecraft mailing list > Post to: Elecraft@mailman.qth.net > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/subscribers.htm > Elecraft web page: http://www.elecraft.com > _______________________________________________ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com