Yes and that was my intent as well....to provide options. That's why the IF was capitalized. :)
------------------------- 73, Greg - AB7R Whidbey Island WA NA-065 On Fri Dec 5 9:42 , "Joe Subich, W4TV" sent: > >> Not true of the KRC2 IF you are using the >> AuxBus line. > >The question was specifically with respect to BCD output - >not Aux Bus. Neither the microHAM Band Decoder not Station >Master require any modification (or care about the BCD >coding) if the serial (CAT) data is used for band decoding >but that wasn't the question that Jan asked. > >Another respondent mentioned an specific band decoding device >from one vendor. My response was to provide the data about >the other available products that Jan was likely to be using >as well as get the full information into the archives so >another person searching for the same information in two or >three years from now was not left to wonder about compatibility >with devices other than one specific product. > >73, > > ... Joe, W4TV > > > >> -----Original Message----- >> From: Greg - AB7R [EMAIL PROTECTED]','','','')">[EMAIL PROTECTED] >> Sent: Friday, December 05, 2008 11:30 AM >> To: '' Jan Erik Holm ''; elecraft@mailman.qth.net; 'Joe; Subich; W4TV' >> Subject: RE: [Elecraft] K3 Band Data >> >> >> The Elecraft KRC-2 and >W9XT Band Decoders do not have >> pull-up resistors and will >require the addition of 2.2 - >> 10K resistors Not true of the KRC2 IF you are using the >> AuxBus line. I have the K3 ACCY AuxBus connected to the KRC2 >> and it works great. No changes needed. >> ------------------------- 73, Greg - AB7R Whidbey Island WA >> NA-065 On Fri Dec 5 7:37 , "Joe Subich, W4TV" sent: > >> >The BCD encoding is the same as the FT-1000D/FT-2000. > >> >Interfacing to a microHAM or TopTen Band Decoder requires >> >no internal modification (both products include pull-up >> >resistors on their BCD inputs). The Elecraft KRC-2 and >> >W9XT Band Decoders do not have pull-up resistors and will >> >require the addition of 2.2 - 10K resistors in the decoder >> >or on the KIO3 board as documented in the Negative ALC >Mod >> bulletin. > >73, > > ... Joe, W4TV > > > > >> >> -----Original Message----- >> From: >> [EMAIL PROTECTED] >> >> [EMAIL PROTECTED]','','','')">elecraft-bounces >> @mailman.qth.net] On Behalf Of Jan Erik Holm >> Sent: Friday, >> December 05, 2008 4:00 AM >> To: Elecraft Reflector >> >> Subject: [Elecraft] K3 Band Data >> >> >> Is the K3 band >> data compatible with Yaesu (ex:FT1000D) >> BCD band data. >> Looks to me that it is, or? >> >> 73 Jim SM2EKM >> >> >> _______________________________________________ >> Elecraft >> mailing list >> Post to: Elecraft@mailman.qth.net >> You must >> be a subscriber to post to the list. >> Subscriber Info >> (Addr. Change, sub, unsub etc.): >> >> http://mailman.qth.net/mailman/listinfo/elecraft >> >> >> Help: http://mailman.qth.net/subscribers.htm >> Elecraft web >> page: http://www.elecraft.com > >> >_______________________________________________ >Elecraft >> mailing list >Post to: Elecraft@mailman.qth.net >You must be >> a subscriber to post to the list. >Subscriber Info (Addr. >> Change, sub, unsub etc.): > >> http://mailman.qth.net/mailman/listinfo/elecraft > >Help: >> http://mailman.qth.net/subscribers.htm >Elecraft web page: >> http://www.elecraft.com >> > _______________________________________________ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com