On Monday 24 June 2019 11:29:44 Gene Heskett wrote: > On Monday 24 June 2019 10:20:14 andy pugh wrote: > > On Mon, 24 Jun 2019 at 15:16, Gene Heskett <[email protected]> > > wrote: > > > dpkg-checkbuildeps fails here, no debian/control has been > > > generated because configure takes a dump. > > > > It's a different configure. (you need to make sure you are in the > > debian directory and running the debian configure) > > And it needs to be configure --uspace (I think, it was hours ago > > that I did it) > > I must have skipped ahead to doing it in the src dir, its working now > after doing that. And apt is installing the list. 294 pkgs, 1.3GB. > That will take a few yet. In fact, everything except where to get it > is dust in the wind until section 3.2 where the real work starts. > > Still had to add about 6 dependencies before configure would run to > completion, but cd ..;dpkg-buildpackage is running now. > > Many thanks, following the web page its too easy to get out of > sequence. > > Humm, just stopped at building rs274ngc. Restarted dpkg-buildpackage, > which starts from square one. And it shouldn't be hot, the -j didn't > have an argument. So we'll see in another hour or so. > > Until its done, bye for now, Thank you Andy.
And I see whats stopping it, same place, out of virtual memory, and despite one of the attached ssd's having a 10GB swap partition, its not mounted! Doesn't show up except as 100 megs in htop, apparently in the u-sd. fstab is blank, so is mounts output. I thought finding an assigning swap was automatic. I'll see if I can dupe whats here in my fstab and put it in the pi's fstab. I think it worked but the only place I can see it after a reboot is in htop. But it must be working, it got past that particular file as it is proceeding now, with htop showing its 75 megs into 9.7GB of swap, and all 4 cores busier than that famous cat on a tin roof. Can I call it progress? I would like to see a sensors output though to see how hot the pi is getting. But getting close to the end I've a boatload of warnings I've not seen before: dh_makeshlibs objdump: debian/linuxcnc-uspace/usr/lib/python2.7/dist-packages/qtvcp/designer/x86_64/qt5.9/libpyqt5_py2.so.tar.gz: File format not recognized dh_installdeb cat debian/linuxcnc-uspace/DEBIAN/shlibs debian/shlibs.pre > debian/shlibs.local dh_shlibdeps -l debian/linuxcnc-uspace/usr/lib dpkg-shlibdeps: warning: debian/linuxcnc-uspace/usr/bin/schedrmt contains an unresolvable reference to symbol __aeabi_atexit@CXXABI_ARM_1.3.3: it's probably a plugin dpkg-shlibdeps: warning: debian/linuxcnc-uspace/usr/bin/milltask contains an unresolvable reference to symbol __aeabi_atexit@CXXABI_ARM_1.3.3: it's probably a plugin dpkg-shlibdeps: warning: debian/linuxcnc-uspace/usr/bin/rs274 contains an unresolvable reference to symbol __aeabi_atexit@CXXABI_ARM_1.3.3: it's probably a plugin dpkg-shlibdeps: warning: debian/linuxcnc-uspace/usr/bin/rtapi_app contains an unresolvable reference to symbol __aeabi_atexit@CXXABI_ARM_1.3.3: it's probably a plugin dpkg-shlibdeps: warning: symbol _Z11PROGRAM_ENDv used by debian/linuxcnc-uspace/usr/lib/librs274.so.0 found in none of the libraries dpkg-shlibdeps: warning: symbol _Z21ENABLE_SPEED_OVERRIDEi used by debian/linuxcnc-uspace/usr/lib/librs274.so.0 found in none of the libraries dpkg-shlibdeps: warning: symbol _Z13SET_FEED_MODEii used by debian/linuxcnc-uspace/usr/lib/librs274.so.0 found in none of the libraries dpkg-shlibdeps: warning: symbol _task used by debian/linuxcnc-uspace/usr/lib/librs274.so.0 found in none of the libraries dpkg-shlibdeps: warning: symbol _Z25GET_EXTERNAL_ANALOG_INPUTid used by debian/linuxcnc-uspace/usr/lib/librs274.so.0 found in none of the libraries dpkg-shlibdeps: warning: symbol _Z13SELECT_POCKETii used by debian/linuxcnc-uspace/usr/lib/librs274.so.0 found in none of the libraries dpkg-shlibdeps: warning: symbol _Z23GET_EXTERNAL_POSITION_Yv used by debian/linuxcnc-uspace/usr/lib/librs274.so.0 found in none of the libraries dpkg-shlibdeps: warning: symbol _Z28WAIT_SPINDLE_ORIENT_COMPLETEid used by debian/linuxcnc-uspace/usr/lib/librs274.so.0 found in none of the libraries dpkg-shlibdeps: warning: symbol _parameter_file_name used by debian/linuxcnc-uspace/usr/lib/librs274.so.0 found in none of the libraries dpkg-shlibdeps: warning: symbol _Z24GET_EXTERNAL_QUEUE_EMPTYv used by debian/linuxcnc-uspace/usr/lib/librs274.so.0 found in none of the libraries dpkg-shlibdeps: warning: 135 other similar warnings have been skipped (use -v to see them all) dpkg-shlibdeps: warning: can't extract name and version from library name 'libtk8.6.so' dpkg-shlibdeps: warning: symbol _Z11PROGRAM_ENDv used by debian/linuxcnc-uspace/usr/lib/libcanterp.so.0 found in none of the libraries But the packages (debs) are built. drwxr-xr-x 2 pi pi 4096 Jun 18 15:25 kernels-rt -rw-r--r-- 1 pi pi 19779 Jun 24 13:16 linuxcnc_2.9.0~pre0_armhf.buildinfo -rw-r--r-- 1 pi pi 2916 Jun 24 13:16 linuxcnc_2.9.0~pre0_armhf.changes drwxr-xr-x 18 pi pi 4096 Jun 24 13:10 linuxcnc-dev -rw-r--r-- 1 pi pi 13138258 Jun 24 13:15 linuxcnc-doc-en_2.9.0~pre0_all.deb -rw-r--r-- 1 pi pi 11636962 Jun 24 13:15 linuxcnc-doc-es_2.9.0~pre0_all.deb -rw-r--r-- 1 pi pi 6157132 Jun 24 13:15 linuxcnc-doc-fr_2.9.0~pre0_all.deb drwxr-xr-x 18 pi pi 4096 Jun 18 10:14 linuxcnc-jessie-dev -rw-r--r-- 1 pi pi 6589218 Jun 24 13:15 linuxcnc-uspace_2.9.0~pre0_armhf.deb -rw-r--r-- 1 pi pi 9211096 Jun 24 13:15 linuxcnc-uspace-dbgsym_2.9.0~pre0_armhf.deb -rw-r--r-- 1 pi pi 741024 Jun 24 13:15 linuxcnc-uspace-dev_2.9.0~pre0_armhf.deb Thanks Andy. Installed, but had to install some more stuff with an sudo apt --fix-broken install, and: latency-test --base-thread shows a max servo jitter of 29 u-secs, which will run a 7i90 running that lathe just fine. Now to get amanda-common and amanda-client installed and enabled then restore my linuxcnc configs and nc_files directories from jessie. And that should put me back in business! (as if there was any business but my hobby stuffs) Setting up amanda to do everything can be involved however. Cheers, Gene Heskett -- "There are four boxes to be used in defense of liberty: soap, ballot, jury, and ammo. Please use in that order." -Ed Howdershelt (Author) If we desire respect for the law, we must first make the law respectable. - Louis D. Brandeis Genes Web page <http://geneslinuxbox.net:6309/gene> _______________________________________________ Emc-developers mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-developers
