In searching UL 60950, don't look for production line tests, look for "Routine Testing". Even then, the only routine testing I found in my very limited search was for routine hipot testing.
Sam From: owner-emc-p...@majordomo.ieee.org [mailto:owner-emc-p...@majordomo.ieee.org]On Behalf Of Jayasinghe, Ryan Sent: Thursday, February 13, 2003 6:26 PM To: 'Rich Nute'; pmerguerian2...@yahoo.com Cc: emc-p...@majordomo.ieee.org Subject: RE: North American Production-Line Tests; ANSI or Other Hello Rich, Good question. I tried tracking this down myself as I had to show my people where the Hi Pot and Bonding tests were required. You can't get from UL1950 to the production line tests. I know it's called out on the Factory Audit Manuals... but where does the requirement come from? What I got a hold of was a UL procedure for their Follow up Services personnel. But I hope you can use this document to further track down the source of the requirement. Try doing a search in Google for "File E211188 Vol. 1" This is where I saw it. File E211188 Vol. 1 Issued: ( ) A P P E N D I X STANDARDIZED APPENDIX PAGES FOR: INFORMATION TECHNOLOGY EQUIPMENT INCLUDING ELECTRICAL BUSINESS EQUIPMENT (NWGQ, NWGQ7), POWER SUPPLIES FOR INFORMATION TECHNOLOGY EQUIPMENT INCLUDING ELECTRICAL BUSINESS EQUIPMENT (QQGQ, QQGQ7), TELEPHONE APPLIANCES AND EQUIPMENT (WYQQ, WYQQ7), POWER SUPPLIES FOR TELEPHONE APPLIANCES AND EQUIPMENT (QQJE, QQJE7) These appendix pages shall also be used for Components Recognized under the categories noted below when one or more descriptive Sections of the Follow-Up Service Procedure require that the manufacturer conduct the factory production-line tests described in Appendix D: (NWGQ2/QQGQ2/WYQQ2/QQJE2) (NWGQ8/QQGQ8/WYQQ8/QQJE8) Ryan Jazz Jayasinghe Canoga Perkins (www.canoga.com <http://www.canoga.com> ) Compliance Engineer 20600 Prairie Street Direct: (818) 678-3898 or x1198 Chatsworth, CA 91311-6008 Main:(818) 718-6300 e-mail: r...@canoga.com <mailto:r...@canoga.com> FAX:(818) 678-3798 From: Rich Nute [mailto:ri...@sdd.hp.com] Sent: Thursday, February 13, 2003 2:52 PM To: pmerguerian2...@yahoo.com Cc: emc-p...@majordomo.ieee.org Subject: Re: North American Production-Line Tests; ANSI or Other Hi Peter: > Anyone knows of ANSI or other North American production-line test > procedures/requirements for electrical/electronic equipment? Some UL > and CSA standards specify the procedures for roduction-line tests, but > what I am looking for is the source of these procedures/requirements. I don't believe any North American standard specifies production-line tests. For UL, production-line tests are specified in the front of each Volume of the UL Follow-Up Services (FUS) procedure. For CSA, I believe production-line tests are specified in the product report. Best regards, Rich This message is from the IEEE EMC Society Product Safety Technical Committee emc-pstc discussion list. Visit our web site at: http://www.ewh.ieee.org/soc/emcs/pstc/ To cancel your subscription, send mail to: majord...@ieee.org with the single line: unsubscribe emc-pstc For help, send mail to the list administrators: Ron Pickard: emc-p...@hypercom.com Dave Heald: davehe...@attbi.com For policy questions, send mail to: Richard Nute: ri...@ieee.org Jim Bacher: j.bac...@ieee.org Archive is being moved, we will announce when it is back on-line. All emc-pstc postings are archived and searchable on the web at: http://www.ieeecommunities.org/emc-pstc This message is from the IEEE EMC Society Product Safety Technical Committee emc-pstc discussion list. Visit our web site at: http://www.ewh.ieee.org/soc/emcs/pstc/ To cancel your subscription, send mail to: majord...@ieee.org with the single line: unsubscribe emc-pstc For help, send mail to the list administrators: Ron Pickard: emc-p...@hypercom.com Dave Heald: davehe...@attbi.com For policy questions, send mail to: Richard Nute: ri...@ieee.org Jim Bacher: j.bac...@ieee.org Archive is being moved, we will announce when it is back on-line. All emc-pstc postings are archived and searchable on the web at: http://www.ieeecommunities.org/emc-pstc This message is from the IEEE EMC Society Product Safety Technical Committee emc-pstc discussion list. Visit our web site at: http://www.ewh.ieee.org/soc/emcs/pstc/ To cancel your subscription, send mail to: majord...@ieee.org with the single line: unsubscribe emc-pstc For help, send mail to the list administrators: Ron Pickard: emc-p...@hypercom.com Dave Heald: davehe...@attbi.com For policy questions, send mail to: Richard Nute: ri...@ieee.org Jim Bacher: j.bac...@ieee.org Archive is being moved, we will announce when it is back on-line. All emc-pstc postings are archived and searchable on the web at: http://www.ieeecommunities.org/emc-pstc
