Thanks for the information Claude. I'm enough confident to give it a try, so I think this week or the next one I'm going to purchase one, and when it finally arrives here and I test it I'm going to post the good news.
El 24 de abril de 2012 10:50, Claude Froidevaux <[email protected]>escribió: > Hi, > > I never used them, but a respectable seller in europe sell them for > typical CN use: > > http://www.kinco.cn/html/en/products/Servo&Stepper/Servo&Stepper_overview/ > > Again, I never use them, so, other advice would be welcome. > > > > Le 21.04.2012 03:20, Leonardo Marsaglia a écrit : > > Sorry, I meant the price is four times the chinese motor+driver. > > > > El 20 de abril de 2012 22:19, Leonardo Marsaglia< > > [email protected]> escribió: > > > >> Thank you guys for your answers. I think I'm going to try these servos, > >> with analog drivers to close the loop on LinuxCNC. > >> > >> James, here in my country, Argentina, there are suppliers that sell > >> yaskawa motors, but the price is four times the price for a chinese > driver, > >> and the connectors and cables are not included. I'm going to check out > on > >> ebay to see if there are some good priced yaskawa servo motors, but I > don't > >> think any other servo motor can be cheaper as the chinese. > >> > >> > >> > >> El 20 de abril de 2012 17:55, James Louis<[email protected] > >escribió: > >> > >> Leonardo, > >>> I have had good luck buying new and used Yaskawa servos from eBay. > >>> Jim > >>> > >>> ----- Original Message ----- > >>> From: Leonardo Marsaglia<[email protected]> > >>> To: Enhanced Machine Controller (EMC)<[email protected]> > >>> Sent: Fri Apr 20 15:08:32 2012 > >>> Subject: [Emc-users] OT: Chinese servo motor > >>> > >>> Hello everybody, > >>> > >>> This is not a pure LinuxCNC question, but it's a question about servo > >>> motors, and I'm going to control them using LinuxCNC, and given the > >>> knowledge and experience on this list I think you could clear some of > my > >>> doubts. > >>> > >>> I'm looking for cheap servo motors to control some positioning > movements > >>> on > >>> a grinder, since the steppers are way too limited in their torque. So I > >>> was > >>> looking for chinese servo motors, (since my steppers and drives are > from > >>> china and work very well), and I found > >>> this: > >>> > http://www.alibaba.com/product-gs/466312062/130ST_M07725_2kw_industrial_motor.html > >>> > >>> I was wondering if any of you have experience with these kind of > servos, > >>> and what do you think about it, because the prices are way too cheap. > USD > >>> 265 for a 2kw servo motor and USD 290 for the driver. So I would be > >>> thanked > >>> if you can tell me your thoughts about this, and of course I'll be more > >>> thanked if you have any recomendation. > >>> > >>> Best regards! > >>> > >>> -- > >>> *Leonardo Marsaglia*. > >>> > >>> > ------------------------------------------------------------------------------ > >>> For Developers, A Lot Can Happen In A Second. > >>> Boundary is the first to Know...and Tell You. > >>> Monitor Your Applications in Ultra-Fine Resolution. Try it FREE! > >>> http://p.sf.net/sfu/Boundary-d2dvs2 > >>> _______________________________________________ > >>> Emc-users mailing list > >>> [email protected] > >>> https://lists.sourceforge.net/lists/listinfo/emc-users > >>> > >>> This communication is for the use of the intended recipient only. It > may > >>> contain information that is privileged and confidential. If you are > not the > >>> intended recipient of this communication, the disclosure, copying, > >>> distribution or use hereof is prohibited. If you have received this > >>> communication in error, please advise me by return e-mail or by > telephone > >>> and then delete it immediately. > >>> > >>> > ------------------------------------------------------------------------------ > >>> For Developers, A Lot Can Happen In A Second. > >>> Boundary is the first to Know...and Tell You. > >>> Monitor Your Applications in Ultra-Fine Resolution. Try it FREE! > >>> http://p.sf.net/sfu/Boundary-d2dvs2 > >>> _______________________________________________ > >>> Emc-users mailing list > >>> [email protected] > >>> https://lists.sourceforge.net/lists/listinfo/emc-users > >>> > >> > >> > >> -- > >> *Leonardo Marsaglia*. > >> > >> > > > > > > ------------------------------------------------------------------------------ > Live Security Virtual Conference > Exclusive live event will cover all the ways today's security and > threat landscape has changed and how IT managers can respond. Discussions > will include endpoint security, mobile security and the latest in malware > threats. http://www.accelacomm.com/jaw/sfrnl04242012/114/50122263/ > _______________________________________________ > Emc-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-users > -- *Leonardo Marsaglia*. ------------------------------------------------------------------------------ Live Security Virtual Conference Exclusive live event will cover all the ways today's security and threat landscape has changed and how IT managers can respond. Discussions will include endpoint security, mobile security and the latest in malware threats. http://www.accelacomm.com/jaw/sfrnl04242012/114/50122263/ _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
