hi Gene what do you see when open machine >hal meter> signal how many items there? what is items number 8?
On Sat, Jul 12, 2014 at 12:35 PM, a k <[email protected]> wrote: > hi > i think that problem in my download > i will make another CD > when i download from > New Installation > > 1. Download the ISO > <http://www.linuxcnc.org/iso/ubuntu-10.04-linuxcnc3-i386.iso> > > will it be automatically---- 2.5.4 ? or 2.5 etc? > > thank you > > > On Fri, Jul 11, 2014 at 2:26 PM, Gene Heskett <[email protected]> wrote: > >> On Friday 11 July 2014 16:26:37 a k did opine >> And Gene did reply: >> > Hi >> > in hal_meter a lot thing, i need to know which one to check. >> > >> > i did >> > hal-meter>signals>home switch> False >> > >> > only x axis home switch change it to True. >> >> I suspect you are not showing an exact copy, that switch, if you have them >> wired separately, should have a label home switch x or y or z. >> >> It is very important that you copy us exactly what you see on screen, >> including the menu paths. >> >> > ////////////////////////////////// >> > in >> > hal_meter>Parameter>hm2_5i20.io_ error >> was the space between io_ and error there? >> >> Now, I am in the middle of making a 5i25 move my small lathe so I am at >> the limit of what I can do here. >> >> But I note that when linuxcnc is shut down, every tally led on my C1G BOB >> goes to full brightness. If the spindle worked, it would be turning the >> motor wide open, somewhere in the 15,000 revs range at the motor shaft. >> My steppers are moving, but very slowly, max 99mm a minute, and with VERY >> leisurely accelerate/decelerate. This was "first light" so to speak. The >> step pulses are so narrow I have to put me in the dark to see a very faint >> glow from the tally leds. And both stepgens are running the motors >> reverse of the correct direction. But I have not turned on my Hitachi >> 100mhz dual trace scope to see whats going on yet. Some of these fixes >> will be fairly simple I believe. >> >> But its about 90F in the shop, I'm 79 and quite well done in this heat so >> for me it can wait. >> >> > i can not read that but it error >> > ////////////////////////////// >> > i think that this down load CD is bad and i can not "fix" it. >> > i need get good down load where all witch work like it was with emc2 >> > --2.2.4. >> > ///////////////// >> > ---- I'm running the latest 2.5.4---- i think my is 2.5 >> >> Did you use synaptic to install it, using this line (just add it to the >> bottom of the list) in your /etc/sources.list: >> >> deb http://buildbot.linuxcnc.org lucid v2.5_branch-rt >> >> If its not in that list, you will not get automatic updates. >> >> Both update-manager and synaptic share this list. You have to >> sudo gedit /etc/apt/sources.list to add that line, and then >> sudo update-manager to update to the last build >> or >> sudo synaptic to un-install/re-install >> >> > On Fri, Jul 11, 2014 at 6:47 AM, Stuart Stevenson <[email protected]> >> wrote: >> > > Aram, >> > > >> > > The description "working good and then not working" is not very >> > > >> > > informative. You need to describe what happens as clear and complete >> > > as you possibly can. >> > > >> > > Do NOT leave out any details. >> > > >> > > Tell us every button push and what happens after every button push. >> > > Tell us everything you see and do. It is almost impossible to send >> > > too much information when you request help. >> > > >> > > Then when someone answers you and/or asks you a question you MUST >> > > answer their questions and respond to their suggestions and >> > > thoughts. >> > > >> > > Don't leave out ANY details as this problem is caused by a minor >> > > detail that is probably something you have done (or maybe not done). >> > > >> > > When someone responds to your request for help you need to then >> > > become a helper to the person responding to your request. >> > > >> > > Pay close attention to what they say or suggest. Do what they want >> > > you to do and then respond with answers that only relate to the >> > > questions or suggestions they sent. >> > > >> > > thanks >> > > Stuart >> > > >> > > --------------------------------------------------------------------- >> > > --------- Open source business process management suite built on Java >> > > and Eclipse Turn processes into business applications with Bonita >> > > BPM Community Edition Quickly connect people, data, and systems into >> > > organized workflows Winner of BOSSIE, CODIE, OW2 and Gartner awards >> > > http://p.sf.net/sfu/Bonitasoft >> > > _______________________________________________ >> > > Emc-users mailing list >> > > [email protected] >> > > https://lists.sourceforge.net/lists/listinfo/emc-users >> > >> > ----------------------------------------------------------------------- >> > ------- _______________________________________________ >> > Emc-users mailing list >> > [email protected] >> > https://lists.sourceforge.net/lists/listinfo/emc-users >> >> >> Cheers, Gene Heskett >> -- >> "There are four boxes to be used in defense of liberty: >> soap, ballot, jury, and ammo. Please use in that order." >> -Ed Howdershelt (Author) >> Genes Web page <http://geneslinuxbox.net:6309/gene> >> US V Castleman, SCOTUS, Mar 2014 is grounds for Impeaching SCOTUS >> >> >> ------------------------------------------------------------------------------ >> _______________________________________________ >> Emc-users mailing list >> [email protected] >> https://lists.sourceforge.net/lists/listinfo/emc-users >> > > ------------------------------------------------------------------------------ _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
