net X-neg-limit axis.0.home-sw-in <= hm2_[HOSTMOT2](BOARD).0.gpio.048.in_not
i think it is wrong line for limit switch something need to be instead axis.0.home-sw-in do not know what ///////////////////////////////////////////////////////////////////////////////// On Sun, Jul 13, 2014 at 2:59 PM, a k <pccncmach...@gmail.com> wrote: > > and for limit it will be > > net X-neg-limit axis.0.home-sw-in <= hm2_[HOSTMOT2](BOARD).0.gpio.03 > 8.in_not > > is it only one line per one limit switch? > > > On Sun, Jul 13, 2014 at 2:36 PM, Peter C. Wallace <p...@mesanet.com> wrote: > >> On Sun, 13 Jul 2014, a k wrote: >> >> Date: Sun, 13 Jul 2014 13:47:04 -0700 >>> >>> From: a k <pccncmach...@gmail.com> >>> Reply-To: "Enhanced Machine Controller (EMC)" >>> <emc-users@lists.sourceforge.net> >>> To: "Enhanced Machine Controller (EMC)" <emc-users@lists.sourceforge.net >>> > >>> Subject: Re: [Emc-users] Homing? >>> >>> so, limit switches and home switches were not there to begin with. >>> >> ////////////////////////////////////////// >> is this what need to add for limit switches >> ### >> ### Sample separate limit switches on the X axis (axis 0) >> ### >> net X-neg-limit parport.0.pin-11-in => axis.0.neg-lim-sw-in >> net X-pos-limit parport.0.pin-12-in => axis.0.pos-lim-sw-in >> >> ///////////////////////////////////////////// >> and for home >> >> ### A sample home switch on the X axis (axis 0). make a signal, >> ### link the incoming parport pin to the signal, then link the signal >> ### to LinuxCNCÿÿs axis 0 home switch input pin >> >> ### >> net Xhome parport.0.pin-10-in => axis.0.home-sw-in >> ### >> >> >> >> Approximately right but you are not using a parallel port >> so the pin names of the hardware side will be different something more >> like: >> >> net Xhome axis.0.home-sw-in <= hm2_[HOSTMOT2](BOARD).0.gpio.048.in_not >> >> >> Note that the gpio number (the 048) depends on which 5I20 connector the >> 7I37 is connected to and which 7I37 input the limit switch connects to. >> >> (the 048 is just an example) >> >> >> On Sun, Jul 13, 2014 at 12:47 PM, John Kasunich <jmkasun...@fastmail.fm> >> wrote: >> >> >>> >>> On Sun, Jul 13, 2014, at 01:58 PM, a k wrote: >>> > hi >>> > ----The example hal file hs no limit switch >>> > support built in so you will have to add the limit switch connections >>> in >>> the >>> > hal file in order for them to become functional >>> > ---- >>> > i want add--limit and home switches. >>> > How i can do that? - add switches >>> > question --why switches are not in hal is for integrator. what is >>> reason >>> to >>> > not put them in as a default? >>> > >>> >>> Because some integrators will want switches and some will not. >>> It is a SAMPLE configuration. It can never be perfect for everyone. >>> You are the integrator, you are expected to look at the samples and >>> learn enough to modify them to suit your own needs. >>> >>> >>> -- >>> John Kasunich >>> jmkasun...@fastmail.fm >>> >>> >>> ------------------------------------------------------------ >>> ------------------ >>> _______________________________________________ >>> Emc-users mailing list >>> Emc-users@lists.sourceforge.net >>> https://lists.sourceforge.net/lists/listinfo/emc-users >>> >>> ------------------------------------------------------------ >> ------------------ >> _______________________________________________ >> Emc-users mailing list >> Emc-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/emc-users >> >> Peter Wallace >> Mesa Electronics >> >> (\__/) >> (='.'=) This is Bunny. Copy and paste bunny into your >> (")_(") signature to help him gain world domination. >> >> >> ------------------------------------------------------------------------------ >> >> _______________________________________________ >> Emc-users mailing list >> Emc-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/emc-users >> >> > ------------------------------------------------------------------------------ _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
