I take it that you got the 7I80 running then. ------ Original Message ------ From: "Rick" <[email protected]> To: "Marius Liebenberg" <[email protected]>; "Enhanced Machine Controller (EMC)" <[email protected]> Sent: 2015-04-06 19:48:31 Subject: Re: [Emc-users] PNCConf setup
>I think I am going to try to start with just the base INI and the main >stuff normally towards the top of the HAL file, temporarily deleting >all pin associated verbage, start-up linux, then look at the pin names >in the "hal show" to see what I am dealing with. > > > >On 4/6/2015 1:44 PM, Marius Liebenberg wrote: >> That is about right Rick. >> >>------ Original Message ------ >>From: "Rick" <[email protected]> >>To: "Enhanced Machine Controller (EMC)" >><[email protected]> >>Sent: 2015-04-06 18:58:51 >>Subject: Re: [Emc-users] PNCConf setup >> >>> I do have a few, 3 to be exact, running almost a carbon copy build >>>(5i23-7i49-7i44-7i71-7i70-7i73), of what I am building now, >>>(7i80-7i49-7i52-7i71-7i70-7i73). >>> >>>Would a line that looked like this before, >>> >>> net spindle-low-range-sol => >>>hm2_5i23.0.7i71.0.3.output-00 >>> >>>Look like this with the 7i80? >>> >>> net spindle-low-range-sol => >>>hm2_7i80.0.7i71.0.3.output-00 >>> >>> >>> >>> >>>On 4/6/2015 12:05 PM, Peter C. Wallace wrote: >>>> On Mon, 6 Apr 2015, Rick wrote: >>>> >>>>> Date: Mon, 06 Apr 2015 11:57:21 -0400 >>>>> From: Rick <[email protected]> >>>>> Reply-To: "Enhanced Machine Controller (EMC)" >>>>> <[email protected]> >>>>> To: Emc Users <[email protected]> >>>>> Subject: [Emc-users] PNCConf setup >>>>> >>>>> Hello Guys, >>>>> >>>>> What would be the closest configuration to try to build with from >>>>>the >>>>> PNCConf utility, I am using the 7i80HD-16 card. I know that the >>>>>card >>>>>is >>>>> not an option yet in the utility, and just want to try to get my >>>>>files >>>>> roughed out with that, instead of trying to hand write my HAL >>>>>file >>>>>from >>>>> scratch. >>>>> >>>>> >>>>> -- >>>>> >>>>> Thanks >>>>> >>>>> >>>>> Rick Lair >>>>> Superior Roll & Turning LLC >>>>> 399 East Center Street >>>>> Petersburg MI, 49270 >>>>> PH: 734-279-1831 >>>>> FAX: 734-279-1166 >>>>> www.superiorroll.com >>>>> >>>> ISTR that you have a 5i23 config with a resolver, that should be a >>>>close >>>> starting point >>>> >>>> >>>>> >>>>>------------------------------------------------------------------------------ >>>>> BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT >>>>> Develop your own process in accordance with the BPMN 2 standard >>>>> Learn Process modeling best practices with Bonita BPM through >>>>>live >>>>>exercises >>>>> http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- >>>>>event?utm_ >>>>> >>>>>source=Sourceforge_BPM_Camp_5_6_15&utm_medium=email&utm_campaign=VA_SF >>>>> _______________________________________________ >>>>> Emc-users mailing list >>>>> [email protected] >>>>> https://lists.sourceforge.net/lists/listinfo/emc-users >>>>> >>>> Peter Wallace >>>> Mesa Electronics >>>> >>>> (\__/) >>>> (='.'=) This is Bunny. Copy and paste bunny into your >>>> (")_(") signature to help him gain world domination. >>>> >>>> >>>> >>>>------------------------------------------------------------------------------ >>>> BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT >>>> Develop your own process in accordance with the BPMN 2 standard >>>> Learn Process modeling best practices with Bonita BPM through live >>>>exercises >>>> http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- >>>>event?utm_ >>>> >>>>source=Sourceforge_BPM_Camp_5_6_15&utm_medium=email&utm_campaign=VA_SF >>>> _______________________________________________ >>>> Emc-users mailing list >>>> [email protected] >>>> https://lists.sourceforge.net/lists/listinfo/emc-users >>>-- >>> >>>Thanks >>> >>> >>>Rick Lair >>>Superior Roll & Turning LLC >>>399 East Center Street >>>Petersburg MI, 49270 >>>PH: 734-279-1831 >>>FAX: 734-279-1166 >>>www.superiorroll.com >>> >>> >>>------------------------------------------------------------------------------ >>>BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT >>>Develop your own process in accordance with the BPMN 2 standard >>>Learn Process modeling best practices with Bonita BPM through live >>>exercises >>>http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- >>>event?utm_ >>>source=Sourceforge_BPM_Camp_5_6_15&utm_medium=email&utm_campaign=VA_SF >>>_______________________________________________ >>>Emc-users mailing list >>>[email protected] >>>https://lists.sourceforge.net/lists/listinfo/emc-users >> >>------------------------------------------------------------------------------ >>BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT >>Develop your own process in accordance with the BPMN 2 standard >>Learn Process modeling best practices with Bonita BPM through live >>exercises >>http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- >>event?utm_ >>source=Sourceforge_BPM_Camp_5_6_15&utm_medium=email&utm_campaign=VA_SF >>_______________________________________________ >>Emc-users mailing list >>[email protected] >>https://lists.sourceforge.net/lists/listinfo/emc-users > >-- >Thanks > > >Rick Lair >Superior Roll & Turning LLC >399 East Center Street >Petersburg MI, 49270 >PH: 734-279-1831 >FAX: 734-279-1166 >www.superiorroll.com > ------------------------------------------------------------------------------ BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15&utm_medium=email&utm_campaign=VA_SF _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
