Fyi, I can get to linuxcnc.org/docs Ray On Oct 13, 2015 5:35 PM, "Sebastian Kuzminsky" <[email protected]> wrote:
> Something's gone wrong with the website and our hosting provider > (Dreamcast) has disabled our site. Our IT specialists have been called > home from vacation and injected with caffeine for a heroic, > around-the-clock debugging effort. > > Stay tuned for more as this breaking story develops. > > > On 10/13/2015 05:55 PM, Dave Cole wrote: > > > > I just got this: > > > > > > Forbidden > > > > You don't have permission to access / on this server. > > > > Additionally, a 403 Forbidden error was encountered while trying to use > > an ErrorDocument to handle the request. > > > > > > > > On 10/13/2015 7:49 PM, jrmitchellj . wrote: > >> I am getting "forbiden" message when I try to connect to it. > >> It worked fine earlier today. > >> > >> Ray > >> On Aug 26, 2015 12:50 AM, "Marius Liebenberg" <[email protected]> > >> wrote: > >> > >>> I changed the input spindle frequency to 200Hz and fixed the scaling. > >>> The input frequency is given and not calculated as it wastes > unnecessary > >>> time. It works very well now. I will use a fast opto coupler to drive > >>> the power source and hopefully I have a solution. > >>> > >>> #define MainPeriod 50 // measurement frame duration, milliseconds > >>> #define pulseInput 2 // input pin for pulseIn > >>> #define pulseOutput 4 > >>> > >>> long previousMillis = 0; > >>> unsigned long duration = 0; // receive pulse width > >>> unsigned long outDuration = 0; > >>> long pulsecount = 0; > >>> long dc = 0; > >>> > >>> float Freq = 0.2e3; > >>> float T = 1 / Freq; > >>> void setup() > >>> { > >>> pinMode(pulseInput, INPUT); > >>> Serial.begin(19200); > >>> pinMode(ledPin, OUTPUT); > >>> analogWriteFrequency(4, 40000); //set the pwm frequency = 25usec > >>> analogWriteResolution(10); // use the highest resolution > >>> } > >>> > >>> void loop() > >>> { > >>> unsigned long currentMillis = millis(); > >>> if (currentMillis - previousMillis >= MainPeriod) > >>> { > >>> previousMillis = currentMillis; > >>> dc = (duration / 5e-3)/1000; > >>> dc = dc / 100; > >>> outDuration = (dc * 1024)/100; > >>> analogWrite(pulseOutput, outDuration); > >>> > >>> // write current time and F values to the serial port > >>> // not implimented for production but handy to see the frequencies > >>> > >>> //Serial.print(currentMillis); > >>> //Serial.print(" "); // separator! > >>> > >>> /*Serial.print(dc); > >>> Serial.print(" "); > >>> Serial.print(pulsecount); > >>> Serial.print(" "); > >>> Serial.print(duration); > >>> Serial.print(" "); > >>> Serial.println(outDuration);*/ > >>> > >>> duration = 0; > >>> pulsecount = 0; > >>> > >>> } > >>> // instead of single measurement per cycle - accumulate and average > >>> duration += pulseIn(pulseInput, HIGH, MainPeriod * 900); > >>> pulsecount++; > >>> > >>> } > >>> > >>> > >>> > >>>> On 25.08.15 14:27, Marius Liebenberg wrote: > >>>>> Erik > >>>>> I am getting to old to be a purist any more. I always use the > >>>>> platform > >>>>> or chip with the best or most intuitive dev environment. > >>>>> Short piece of code using a Teensy 3.0. I use the Visual Micro > >>>>> debugger > >>>>> in Microsoft Visual Studio 2015 all running on the latest Arduino > >>>>> environment. > >>>> <Chuckle>. Marius, I've feared I'm too old to learn the newfangled > >>>> Arduino environment, so I'm thrilled to see how you've leveraged it. > >>>> The speed of getting it going is very impressive. I should take a > >>>> closer > >>>> look at the environment - I think I've seen somewhere that it can be > >>>> used with the gnu toolchain. > >>>> > >>>> Erik > >>>> > >>>> > ------------------------------------------------------------------------------ > >>>> _______________________________________________ > >>>> Emc-users mailing list > >>>> [email protected] > >>>> https://lists.sourceforge.net/lists/listinfo/emc-users > >>> > ------------------------------------------------------------------------------ > >>> _______________________________________________ > >>> Emc-users mailing list > >>> [email protected] > >>> https://lists.sourceforge.net/lists/listinfo/emc-users > >>> > >> > ------------------------------------------------------------------------------ > >> _______________________________________________ > >> Emc-users mailing list > >> [email protected] > >> https://lists.sourceforge.net/lists/listinfo/emc-users > > > > > > --- > > This email has been checked for viruses by Avast antivirus software. > > https://www.avast.com/antivirus > > > ------------------------------------------------------------------------------ > > _______________________________________________ > > Emc-users mailing list > > [email protected] > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > -- > Sebastian Kuzminsky > > > ------------------------------------------------------------------------------ > _______________________________________________ > Emc-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-users > ------------------------------------------------------------------------------ _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
