On Wednesday 20 January 2016 12:22:24 Gene Heskett wrote: Third update:
Nothing I can do will make it build the docs, in either .html or .pdf format, and no errors are being reported even if I run the Makefile in any of the three docs subdirs. The Makefiles are being updated when I rerun ./configure, but make can't find anything to do in any of the subdirs of doc. This I think, should be the first problem I solve as that may enable solving the rest of it. But there aren't any errors being reported by make. There is a "make clean" immediately above this paste: gene@GO704:~/linuxcnc/camview-emc.src/docs$ make Making all in reference make[1]: Entering directory `/home/gene/linuxcnc/camview-emc.src/docs/reference' Making all in libcamunits make[2]: Entering directory `/home/gene/linuxcnc/camview-emc.src/docs/reference/libcamunits' make[2]: Nothing to be done for `all'. make[2]: Leaving directory `/home/gene/linuxcnc/camview-emc.src/docs/reference/libcamunits' Making all in libcamunits-gtk make[2]: Entering directory `/home/gene/linuxcnc/camview-emc.src/docs/reference/libcamunits-gtk' make[2]: Nothing to be done for `all'. make[2]: Leaving directory `/home/gene/linuxcnc/camview-emc.src/docs/reference/libcamunits-gtk' make[2]: Entering directory `/home/gene/linuxcnc/camview-emc.src/docs/reference' make[2]: Nothing to be done for `all-am'. make[2]: Leaving directory `/home/gene/linuxcnc/camview-emc.src/docs/reference' make[1]: Leaving directory `/home/gene/linuxcnc/camview-emc.src/docs/reference' Making all in tutorial make[1]: Entering directory `/home/gene/linuxcnc/camview-emc.src/docs/tutorial' make[1]: Nothing to be done for `all'. make[1]: Leaving directory `/home/gene/linuxcnc/camview-emc.src/docs/tutorial' Making all in plugins make[1]: Entering directory `/home/gene/linuxcnc/camview-emc.src/docs/plugins' Making all in build make[2]: Entering directory `/home/gene/linuxcnc/camview-emc.src/docs/plugins/build' make[2]: Nothing to be done for `all'. make[2]: Leaving directory `/home/gene/linuxcnc/camview-emc.src/docs/plugins/build' make[2]: Entering directory `/home/gene/linuxcnc/camview-emc.src/docs/plugins' make[2]: Nothing to be done for `all-am'. make[2]: Leaving directory `/home/gene/linuxcnc/camview-emc.src/docs/plugins' make[1]: Leaving directory `/home/gene/linuxcnc/camview-emc.src/docs/plugins' make[1]: Entering directory `/home/gene/linuxcnc/camview-emc.src/docs' make[1]: Nothing to be done for `all-am'. make[1]: Leaving directory `/home/gene/linuxcnc/camview-emc.src/docs' Puzzled is an understatement. And I don't know enough about Makefile's to decode them. > On Wednesday 20 January 2016 10:34:40 Gene Heskett wrote: > > Second update: > > Now linuxcnc runs again, but shows a white screen and none of the > halui buttons, just the blank window. > > And on the screen that I launch it from a snapshot.png is attached. > Taken with this same camera :) > > The invalid option -C, if removed but the following filename remains, > gets me the same exact error from the next -g togle.ui option. And if > I remove that, the -H campins.hal, the -H is an error. Puzzling... > > Did I miss adding a build option? > > > On Wednesday 20 January 2016 09:44:27 Gene Heskett wrote: > > > > Update: ssh'd into the GO704 machine, I put a copy of the tarballs > > contents in ~/linuxcnc/src directory. Configure failed, no libv4l2 > > stuffs. Had synaptic install the -dev version. > > > > No clue if it will work, but > > ./configure --with-v4l2-plugin; make > > Worked, and so did a make install, which went to the default > > /usr/local. > > > > Time to go add those two lines to the .ini file & see how many > > complaints that generates for a "linuxcnc -l" launch. > > > > Having a heat wave, we started at about 3F, up to 10F now. Stay > > warm folks. > > > > > Greetings; fresh thread. > > > > > > I downloaded a tarball from psha.orh.ru, containing 0.2.0.7 > > > sources > > > > > > Unpacking it into a ~/src/camview-emc directory, > > > > > > "./configure --with-v4l2-plugin --with-v4l-plugin" > > > > > > appeared to work, but despite having v4l2.dev stuff installed, > > > make exits a minute or so later with this: > > > > > > libtool: compile: > > > gcc -DHAVE_CONFIG_H -I. -I../.. -I../.. -pthread > > > -I/usr/include/glib-2.0 -I/usr/lib/i386-linux-gnu/glib-2.0/include > > > -std=gnu99 -Wall -Wmissing-declarations -Wmissing-prototypes > > > -D_FILE_OFFSET_BITS=64 -D_LARGEFILE_SOURCE -g -O2 -MT > > > input_v4l2.lo -MD -MP -MF .deps/input_v4l2.Tpo -c input_v4l2.c > > > -fPIC -DPIC -o .libs/input_v4l2.o input_v4l2.c: In function > > > ‘add_control’: input_v4l2.c:385:14: error: ‘V4L2_CID_HCENTER’ > > > undeclared (first use in this function) input_v4l2.c:385:14: note: > > > each undeclared identifier is reported only once for each function > > > it appears in input_v4l2.c:386:14: error: ‘V4L2_CID_VCENTER’ > > > undeclared (first use in this function) make[3]: *** > > > [input_v4l2.lo] Error 1 > > > > > > I would assume this might identify the crosshairs, but I've no > > > clue what header file is still missing. Does this ring any bells, > > > Jon? Or anyone else that has opened this can of worms on a wheezy > > > based system? > > > > > > Cheers, Gene Heskett > > > > Cheers, Gene Heskett > > Cheers, Gene Heskett Cheers, Gene Heskett -- "There are four boxes to be used in defense of liberty: soap, ballot, jury, and ammo. Please use in that order." -Ed Howdershelt (Author) Genes Web page <http://geneslinuxbox.net:6309/gene> ------------------------------------------------------------------------------ Site24x7 APM Insight: Get Deep Visibility into Application Performance APM + Mobile APM + RUM: Monitor 3 App instances at just $35/Month Monitor end-to-end web transactions and take corrective actions now Troubleshoot faster and improve end-user experience. Signup Now! http://pubads.g.doubleclick.net/gampad/clk?id=267308311&iu=/4140 _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
