On Tuesday 16 February 2016 10:03:27 John Thornton wrote: > A multi-label will handle the label changes, not sure what your asking > for the hal pins to do that you can't do in hal with logic components. > > JT
That is not the problem, at least so far. I take it that you have not seen what camview-emc could once do? All of that is working right now except for calibration of the camera's offset from the spindle centerline. The scripts all get run when I click on the gui's added buttons. They don't do much without valid data, but they do run. In the meantime, I have found an editor (xmlcopyeditor) written specifically to edit xml files, so I have made a teeny bit of headway in that at least I can see where I have a tag miss-match now. But I've been getting the camera mounted today, and I am about bushed. The mount is solid, but when I put a bolt & washer on the base to serve as an always assembles correctly stopper, I put in dead center in the edge of the base, forgetting there was a trench for camera cable exit there in the camera carrier so it slides right on by the washer. Not a biggie as I can do the same on the camera carrier tomorrow except use 2 3mmx5 bolts so they catch the ears of the dovetail, locating it a fixed distance from the spindle centerline. But the 3mm x 5mm long bolts are a trip to HomeDepot in Bridgeport. I'm fresh out + I need some x10's & x12's to shrink the envelope of the carrier anyway. The x18's I had to use stick out like a sore thumb. :( So I spent the last hour jacking on camera holding screws, more 3mm cap screws, getting the parallax out of the up/down motion while keeping the image something resembling vertical. Thanks John. > On 2/15/2016 8:59 PM, Gene Heskett wrote: > > Howdy all; > > > > Looking at the gui additions for the camera stuff, is it possible to > > have a bidirectional button by associating the button click with a > > halpin that is an output, but use a 2nd halpin as an input to > > control both the text in the button and its color with this 2nd > > halpin? > > > > I am assuming that under all this it is Tkinter doing the actual gfx > > bit twidling. Is that where I should be looking for helpful hints? > > What is discussed in the manual starting on page 386 does not seem > > to indicate the possiblity of using two hal "wires" to control one > > button. If a second halpin could be defined, and an on_text string > > and an off_text string defined just as in on_color and off_color, > > that would be the bee's knees. > > > > Thanks. > > > > Cheers, Gene Heskett > > ---------------------------------------------------------------------- >-------- Site24x7 APM Insight: Get Deep Visibility into Application > Performance APM + Mobile APM + RUM: Monitor 3 App instances at just > $35/Month Monitor end-to-end web transactions and take corrective > actions now Troubleshoot faster and improve end-user experience. > Signup Now! > http://pubads.g.doubleclick.net/gampad/clk?id=272487151&iu=/4140 > _______________________________________________ > Emc-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-users Cheers, Gene Heskett -- "There are four boxes to be used in defense of liberty: soap, ballot, jury, and ammo. Please use in that order." -Ed Howdershelt (Author) Genes Web page <http://geneslinuxbox.net:6309/gene> ------------------------------------------------------------------------------ Site24x7 APM Insight: Get Deep Visibility into Application Performance APM + Mobile APM + RUM: Monitor 3 App instances at just $35/Month Monitor end-to-end web transactions and take corrective actions now Troubleshoot faster and improve end-user experience. Signup Now! http://pubads.g.doubleclick.net/gampad/clk?id=272487151&iu=/4140 _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
