Yep, Ken that's the one. Dick ----- Original Message ----- From: "Ken Strauss" <[email protected]> To: "'Enhanced Machine Controller (EMC)'" <[email protected]> Sent: Tuesday, August 30, 2016 1:15 PM Subject: Re: [Emc-users] Silly Q about glues
> Is that what you meant? > http://makezine.com/2016/03/25/dont-glue-anything-without-handy-reference-ch > art/ > > >> -----Original Message----- >> From: R.L. Wurdack [mailto:[email protected]] >> Sent: Tuesday, August 30, 2016 2:05 PM >> To: Enhanced Machine Controller (EMC) >> Subject: Re: [Emc-users] Silly Q about glues >> >> Sorry, Gene. My mags are down at the ranch and I'm picking apples up here > at >> the farm. I'll look up the reference as soon as I have a chance. >> >> Richard. >> >> >> ----- Original Message ----- >> From: "Gene Heskett" <[email protected]> >> To: <[email protected]> >> Sent: Thursday, August 25, 2016 10:00 AM >> Subject: Re: [Emc-users] Silly Q about glues >> >> >> > On Thursday 25 August 2016 12:35:40 R.L. Wurdack wrote: >> > >> >> ""Make"" magazine a while back had a nice table of glues vs >> >> applications that I found useful. >> >> >> >> Dick >> >> >> > I just spent half an hour clicking "more" without finding it. >> > >> > Thank you for trying. >> >> >> >> ----- Original Message ----- >> >> From: "Gene Heskett" <[email protected]> >> >> To: <[email protected]> >> >> Sent: Thursday, August 25, 2016 9:25 AM >> >> Subject: [Emc-users] Silly Q about glues >> >> >> >> > Greetings; >> >> > >> >> > Trying to carve the toolpost support for the little monster, on the >> >> > little monster. I had it lopsided in the chuck, roughly centered on >> >> > the QC's bolt hole. But that meant the chuck jaws were turned around >> >> > and I couldn't get to the bottom 9/16 of an inch because of flying >> >> > jaws . I needed the cutaway down to perhaps 3mm of the carriage >> >> > sled, so I wrote some gcode to cut the hollowed out curve. I was >> >> > going to see if I could put it on the faceplate, but its a full 7" >> >> > in diameter and hits the motor & electronics box on the back of the >> >> > lathe. >> >> > >> >> > So that was out. I put the 5" 4 jaw back on, w/o the jaws, putting a >> >> > live center in the tailstock, I ran it out far enough to get some >> >> > saddle movement room but left it pushing about 100lbs worth and ran >> >> > a line of fresh superglue all the way around it.. >> >> > >> >> > Setting up the start-stop and done settings in my gcode, I had a >> >> > good pressure on it, and had cleaned the face of the chuck with >> >> > acetone, so superglue should have stuck it for a non-slip grip. >> >> > Peeled it loose on the third touch of the tool. 3 times now, with >> >> > longer setting times each time. >> >> > >> >> > If I can find it, I've some double stick tape, or does someone else >> >> > have an even better idea? >> >> > >> >> > Thanks. >> >> > >> >> > Cheers, Gene Heskett >> >> > -- >> >> > "There are four boxes to be used in defense of liberty: >> >> > soap, ballot, jury, and ammo. Please use in that order." >> >> > -Ed Howdershelt (Author) >> >> > Genes Web page <http://geneslinuxbox.net:6309/gene> >> >> > >> >> > -------------------------------------------------------------------- >> >> >---------- _______________________________________________ >> >> > Emc-users mailing list >> >> > [email protected] >> >> > https://lists.sourceforge.net/lists/listinfo/emc-users >> >> >> >> ---------------------------------------------------------------------- >> >>-------- _______________________________________________ >> >> Emc-users mailing list >> >> [email protected] >> >> https://lists.sourceforge.net/lists/listinfo/emc-users >> > >> > >> > Cheers, Gene Heskett >> > -- >> > "There are four boxes to be used in defense of liberty: >> > soap, ballot, jury, and ammo. Please use in that order." >> > -Ed Howdershelt (Author) >> > Genes Web page <http://geneslinuxbox.net:6309/gene> >> > >> > > ---------------------------------------------------------------------------- > -- >> > _______________________________________________ >> > Emc-users mailing list >> > [email protected] >> > https://lists.sourceforge.net/lists/listinfo/emc-users >> > >> > >> >> >> >> > ---------------------------------------------------------------------------- > -- >> _______________________________________________ >> Emc-users mailing list >> [email protected] >> https://lists.sourceforge.net/lists/listinfo/emc-users > > > > ------------------------------------------------------------------------------ > _______________________________________________ > Emc-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-users > > ------------------------------------------------------------------------------ _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
