This is why posting a screen shot or 3MF is needed. The 0.3 could be anything. When I make something I keep the .STL, the .gcode and the .3mf files together in one place "forever" so that if I want to re-make the part I just load the 3mf file and all the settings are restored.
I am thinking of a system where I write a serial number on the part so I can find its 3MF file later. My point is that the 3mf keeps your work and remembers what you did for you. Now to find a white ink Sharpie. On the positive side, I just discovered that I can get a near-perfect surface finish on PLA using a lathe. I used a brazed-on carbide boring bar to clean the inside of a PLA pulley. I took a 0.005 cut at very low rpm (to avoid melting the plastic) and got a smooth inside that is a light press fit to the 24mm steel hub. I think I will try red (permanent) Locktight and see how it holds up. On Sat, Jun 6, 2020 at 11:14 AM Gene Heskett <[email protected]> wrote: > On Saturday 06 June 2020 14:01:52 Chris Albertson wrote: > > > DO I read this as using 0.3mm line width? If the nozzle has a 0.4mm > > hole you must set the line width to 0.4. > > I don't recall setting that, it was an autoselected choice that I think > came with the super quality setting. If I make it bigger, how much > bigger? > > > Cura will run the extruders at a rate that pumps plastic to make a > > linewitdth x layerthickness x speed. So if you say 0.3 line, then it > > will pump out 3/4 as much plastic as required and move over 0.3 to > > print the next line and will mess up what it just printed. > > > > The 3mm wall and also explains your very long print times. I'm > > making usable 40T pulleys in one hour 10 minutes > > > > I would print with all default settings but do enable support > > "everywhere" as it will only be used if needed. At least until you > > get a good looking 5mm test cube. > > > > On Sat, Jun 6, 2020 at 10:34 AM Gene Heskett <[email protected]> > wrote: > > > On Saturday 06 June 2020 13:01:32 andy pugh wrote: > > > > On Sat, 6 Jun 2020 at 17:56, Gene Heskett <[email protected]> > > > > wrote: > > > > > > > > Here ya go Andrew. A bit fuzzier on the far side, > > > > > > > > > > > > Do you have any wall at all? That looks to be _all_ infill. > > > > > > To me too. > > > > > > > In "Quality" what is your > > > > > > "Wall line width" =0.3 > > > > > > > and then in "Shell" what is your > > > > > > "Wall thickness" =3.0mm > > > > > > > and > > > > > > "Wall line count" =10.0 > > > > > > Thanks Andy > > > > > > Cheers, Gene Heskett > > > -- > > > "There are four boxes to be used in defense of liberty: > > > soap, ballot, jury, and ammo. Please use in that order." > > > -Ed Howdershelt (Author) > > > If we desire respect for the law, we must first make the law > > > respectable. - Louis D. Brandeis > > > Genes Web page <http://geneslinuxbox.net:6309/gene> > > > > > > > > > _______________________________________________ > > > Emc-users mailing list > > > [email protected] > > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > Cheers, Gene Heskett > -- > "There are four boxes to be used in defense of liberty: > soap, ballot, jury, and ammo. Please use in that order." > -Ed Howdershelt (Author) > If we desire respect for the law, we must first make the law respectable. > - Louis D. Brandeis > Genes Web page <http://geneslinuxbox.net:6309/gene> > > > _______________________________________________ > Emc-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-users > -- Chris Albertson Redondo Beach, California _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
