On Mon, 9 Nov 2026, John Dammeyer wrote:

> I had the equivalent for my BeagleBone Black which used the co-processor to 
> create the step/dir and ran a version of LinuxCNC called MachineKit.  The 
> only thing wrong with the board was that it used NO switches for limit etc.  
> Very dangerous.  I did actually run my mill with it for a short time.  
> However Xylotex appears to be gone as is MachineKit.
>
>> -----Original Message-----
>> From: Sam Sokolik [mailto:[email protected]]
>> Sent: November 9, 2026 11:19 AM
>> To: Enhanced Machine Controller (EMC)
>> Subject: Re: [Emc-users] raspberry pi and parallel port
>>
>> I would second mesa hardware...  But..
>>
>> I have one of these and it works 'ok'
>>
>> You are pretty limited in step output speed
>>
>> https://byte2bot.com/products/parallel-port-raspberry-pi-hat
>>
>> In his configs - the base thread is 150000ns - which without reset
>> functionality (I don't know if the gpio in the rpi allows for that) is
>> 3.3khz.
>>
>> But certainly usable for some things..
>>
>> sam
>>
>> On Mon, Nov 9, 2026 at 11:30�AM andy pugh <[email protected]>
>> wrote:
>>
>>> On Mon, 9 Nov 2026 at 01:08, fxkl47BF--- via Emc-users
>>> <[email protected]> wrote:
>>>>
>>>> i have a small cnc router that is driven by the parallel port of a pc
>>>> i see at "https://www.linuxcnc.org/docs/html/drivers/hal_pi_gpio.html";
>>> that i can use the gpio pins of a raspberry pi for this
>>>> is anyone doing this and can you share what you learned
>>>
>>> There should be enough pins to replace a parallel port, however you
>>> might have trouble with voltage levels.
>>> Does your equipment work properly with 3.3V signals? And are any
>>> inputs to the Pi at a safe voltage for the Pi? (switches and even
>>> Proximity sensors can switch-to-gnd so are not a problem there)
>>>
>>> I hesitate to recommend them, as PCW has a living to make, but there
>>> are some cheap clones of the "7i92" board on AliExpress. None of them
>>> bear any real similarity to a real 7i92, so I am unsure why they
>>> picked that designation.
>>> I recently bought one to see what they were like, and to be fair it's
>>> quite nice, with a DIN-rail mounting case and two ethernet sockets for
>>> smart-serial expansion boards.
>>> The only real drawback over a real Mesa board is that the
>>> documentation is terrible, support is likely to be nonexistent and for
>>> some reason it insists on two separate 24V supplies, yet all GPIO is
>>> 5V.
>>>
>>> The one that I got was this one:
>>> https://www.aliexpress.com/item/1005010164851154.html
>>> As is always the case with AliExpress, you have to look beyond the
>>> headline price and factor in shipping. And bear in mind that as
>>> someone else observed "it is like buying stuff from raccoons that have
>>> no idea what anything is for or what it should cost"
>>>
>>>
>>> --
>>> atp
>>> "A motorcycle is a bicycle with a pandemonium attachment and is
>>> designed for the especial use of mechanical geniuses, daredevils and
>>> lunatics."
>>> � George Fitch, Atlanta Constitution Newspaper, 1912


the board is a xylotex but it does have extra inputs that i use for limit 
switches
i bought the machine in 2011

it's all 5v so not going to work with raspberry pi
_______________________________________________
Emc-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/emc-users

Reply via email to