It doesn't look like I can do that from within Netsight. Polling from within Netsight seems to be limited to just discovery making sure the switch is up but I don't see a way to look for specific OIDs as you have defined below. Am I missing something or are you doing this from outside of Netsight, e.g. Nagios?
Thanks John Kaftan IT Infrastructure Manager Utica College 315.792.3102 -----Original Message----- From: Strebler, Reinhard (SCC) [mailto:[email protected]] Sent: Thursday, February 02, 2012 3:12 AM To: John Kaftan Cc: [email protected] Subject: Re: [enterasys] Power Supply Trap Hi John, For monitoring status of power supplies and fan we use SNMP. I've included an example for OIDs and values fo a C5: Number and instances of power supplies SNMPv2-SMI::enterprises.52.4.3.1.2.1.1.1.101 = INTEGER: 101 SNMPv2-SMI::enterprises.52.4.3.1.2.1.1.1.102 = INTEGER: 102 State of power supplies [infoNotAvailable(1), notInstalled(2), installedAndOperating(3), installedAndNotOperating(4)] SNMPv2-SMI::enterprises.52.4.3.1.2.1.1.2.101 = INTEGER: 3 SNMPv2-SMI::enterprises.52.4.3.1.2.1.1.2.102 = INTEGER: 2 Redundancy status of power supplies [redundant(1), notRedundant(2), notSupported(3)] SNMPv2-SMI::enterprises.52.4.3.1.2.1.1.4.101 = INTEGER: 1 SNMPv2-SMI::enterprises.52.4.3.1.2.1.1.4.102 = INTEGER: 1 --> The information provided by these OID must be interpreted in dependancy on "State of power supplies" and are valid only if more than one power supply is installed (built in and external power supply). Number of fan modules SNMPv2-SMI::enterprises.52.4.3.1.3.1.1.1.101 = INTEGER: 101 SNMPv2-SMI::enterprises.52.4.3.1.3.1.1.1.102 = INTEGER: 102 SNMPv2-SMI::enterprises.52.4.3.1.3.1.1.1.103 = INTEGER: 103 SNMPv2-SMI::enterprises.52.4.3.1.3.1.1.1.104 = INTEGER: 104 State of fan modules [infoNotAvailable(1), notInstalled(2), installedAndOperating(3), installedAndNotOperating(4)] SNMPv2-SMI::enterprises.52.4.3.1.3.1.1.2.101 = INTEGER: 3 SNMPv2-SMI::enterprises.52.4.3.1.3.1.1.2.102 = INTEGER: 2 SNMPv2-SMI::enterprises.52.4.3.1.3.1.1.2.103 = INTEGER: 3 SNMPv2-SMI::enterprises.52.4.3.1.3.1.1.2.104 = INTEGER: 2 In case of fan failures syslog messages are been generated. I hope this helps Reinhard Karlsruher Institut für Technologie (KIT) Steinbuch Centre for Computing (SCC) Dipl.-Ing. Reinhard Strebler Abteilungsleiter Netze und Telekommunikation (NET) Kaiserstraße 12 76131 Karlsruhe Telefon: +49 721 608-42068/29046 Fax: +49 721 32550 E-Mail: [email protected] www.scc.kit.edu KIT - Universität des Landes Baden-Württemberg und nationales Forschungszentrum in der Helmholtz-Gemeinschaft Am 01.02.2012 21:55, schrieb John Kaftan: > Hello: > > We have recently converted to Enterasys from Cisco. I am getting my > monitoring and alerting setup and would like to know what you find > useful to alert on as well as how to do it. > > Currently I am looking for a way to know if a power supply fails. If > a switch has an RPS and the primary PS goes down I'd like to know about it. > Is there a way to make that happen? So far my C5 is not sending a > trap or a syslog message when I unplug the primary PS. > > Thanks > > > John Kaftan > IT Infrastructure Manager > Utica College > 315.792.3102 > > > --- > To unsubscribe from enterasys, send email to [email protected] with the > body: unsubscribe enterasys [email protected] --- To unsubscribe from enterasys, send email to [email protected] with the body: unsubscribe enterasys [email protected]
