HaHa <running to the server room to "retroubleshoot" that one problem server>
-----Original Message-----
From: Martin Blackstone [mailto:[EMAIL PROTECTED]]
Sent: Tuesday, September 25, 2001 3:06 PM
To: Exchange Discussions
Subject: RE: Disaster Recovery Test -Failure to start the IS service
The server was unplugged
-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED]] On Behalf Of Stevens, Dave
Sent: Tuesday, September 25, 2001 1:00 PM
To: Exchange Discussions
Subject: RE: Disaster Recovery Test -Failure to start the IS service
what ended up being the problem?
-----Original Message-----
From: Sethi, Ali [mailto:[EMAIL PROTECTED]]
Sent: Tuesday, September 25, 2001 1:14 PM
To: Exchange Discussions
Subject: RE: Disaster Recovery Test -Failure to start the IS service
I was able to resolve this issue. Thanks for everyone that responded to
this problem.
Ali Sethi
Engineer
170 South Warner Road
Suite 110
Wayne, PA. 19087
610-971-9171 ext 306
610-971-9181 fax
www.kenexa.com
The information transmitted is intended only for the person or entity to
which it is addressed and may contain confidential and/or privileged
material. Any review, retransmission, dissemination, distribution,
forwarding, or other use of, or taking of any action in reliance upon,
this information by persons or entities other than the intended
recipient is prohibited without the express permission of the sender. If
you received this communication in error, please contact the sender and
delete the material from any computer.
-----Original Message-----
From: Martin Blackstone [mailto:[EMAIL PROTECTED]]
Sent: Monday, September 24, 2001 6:30 PM
To: Exchange Discussions
Subject: RE: Disaster Recovery Test -Failure to start the IS service
Have you read the MSExchange Disaster Recovery whitepaper yet?
-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED]] On Behalf Of Sethi, Ali
Sent: Monday, September 24, 2001 3:28 PM
To: Exchange Discussions
Subject: Disaster Recovery Test -Failure to start the IS service
Hello,
I decided to do a DR test today but unfortunately could not get the IS
service to start after the restore. Below are my steps in the exact
order: Current Exchange server running 5.5 with sp4 on a windows 2k
server
1.Setup a separate Lan and promoted a bdc that I took off from our
existing network to a pdc.
2.Ran setup of Exchange 5.0. Did not join existing domain. 3.Gave the
server the same name as the orginal exchange server, the same site and
organization names as the existing exchange server. (Understanding that
the site and organization names are case-sensitive) 4.Created a new
site. 5.Selected the same service account as the original exchange
server
6.Did a directory Import from the most current directory.csv file
7.Upgraded recovery server to Exchange 5.5 then SP 4. (same as original
server)
8.Ran MS Exchange performance optimizer
9.Deleted and re-added the computer name on the pdc to create a new sid.
(After readding computer I was forced to remove the recovery server from
the domain and then re-add it to the domain) 10.Installed MS Outlook on
recovery server. 11.Performed the restore using the last full backup
tape (Used Veritas Backup Exec ver 8.6). Restored only the Information
Store not the Directory since that was already imported in step 6.
(Note: I normally do a brick level backup so the tape consisted of the
Directory store, Info store, and part of the individual mailboxes. The
second tape contained the remainder of the mailboxes) The info store
was approximately 33gb. 12.Restored both Priv and Pub data by selecting
them on the Exchange tab in Veritas backup exec ver 8.6.
13. Once the restore was completed the Diretory, MTA, System Attendent
all started but the Info store would not start. Also I could not do an
isinteg -patch because it could not find the IS database.
14. I manually tried to start the IS service but received the error:
Windows could not start the MS IS service on the local computer and to
check the Event viewer for more info. The Event Viewer said: MS IS
service terminated with server specific error 4294966266.
15. Im going to check the knowledge base regarding this error but im
curious if any has ever come across this? Did I not do a step right?
Should I have not imported the Directory store in step 6? Im a little
stumped as to what I did wrong causing the IS not to start.
Anyone have any ideas???
Thanks,
_________________________________________________________________
List posting FAQ: http://www.swinc.com/resource/exch_faq.htm
Archives: http://www.swynk.com/sitesearch/search.asp
To unsubscribe: mailto:[EMAIL PROTECTED]
Exchange List admin: [EMAIL PROTECTED]
_________________________________________________________________
List posting FAQ: http://www.swinc.com/resource/exch_faq.htm
Archives: http://www.swynk.com/sitesearch/search.asp
To unsubscribe: mailto:[EMAIL PROTECTED]
Exchange List admin: [EMAIL PROTECTED]
_________________________________________________________________
List posting FAQ: http://www.swinc.com/resource/exch_faq.htm
Archives: http://www.swynk.com/sitesearch/search.asp
To unsubscribe: mailto:[EMAIL PROTECTED]
Exchange List admin: [EMAIL PROTECTED]
_________________________________________________________________
List posting FAQ: http://www.swinc.com/resource/exch_faq.htm
Archives: http://www.swynk.com/sitesearch/search.asp
To unsubscribe: mailto:[EMAIL PROTECTED]
Exchange List admin: [EMAIL PROTECTED]
_________________________________________________________________
List posting FAQ: http://www.swinc.com/resource/exch_faq.htm
Archives: http://www.swynk.com/sitesearch/search.asp
To unsubscribe: mailto:[EMAIL PROTECTED]
Exchange List admin: [EMAIL PROTECTED]
_________________________________________________________________
List posting FAQ: http://www.swinc.com/resource/exch_faq.htm
Archives: http://www.swynk.com/sitesearch/search.asp
To unsubscribe: mailto:[EMAIL PROTECTED]
Exchange List admin: [EMAIL PROTECTED]
