Yes, thank you for the correction. That is correct and A1 in the FAQ section 3.23 would concur. If using the routing tab. http://www.swinc.com/resource/exch_faq_sec3.htm
However, try if the two address formats are not homogenous namespaces. For example: [EMAIL PROTECTED] [EMAIL PROTECTED] [EMAIL PROTECTED] To go back and answer Simon's original question, Exchange2000 uses SMTP to route email. The full SMTP address is typically required. William -----Original Message----- From: Rickenbacher Beat [mailto:[EMAIL PROTECTED]] Sent: Thursday, April 11, 2002 11:57 PM To: '[EMAIL PROTECTED]' Subject: AW: Multiple Domains in Exchange 2000 In Ex55 there it is not necessary to apply the secondary-proxy-address with that second domain. If the MX Record points to your Ex55-Box then you'll get the mail addressed to the secondary address in your email box. I just did a test (again to verify my ancient knowledge...) :-) Ricki -----Ursprüngliche Nachricht----- Von: William Lefkovics [mailto:[EMAIL PROTECTED]] Gesendet: Donnerstag, 11. April 2002 19:45 An: MS-Exchange Admin Issues Betreff: RE: Multiple Domains in Exchange 2000 Users still would need the secondary-proxy-address with that second domain in order to receive email. In Exchange2000, the process is similar. You can use Recipient Policies to control this. http://support.microsoft.com/search/preview.aspx?scid=kb;en-us;Q319201 William Lefkovics, MCSE, A+ -----Original Message----- From: Simon Butler [mailto:[EMAIL PROTECTED]] Sent: Thursday, April 11, 2002 10:39 AM To: MS-Exchange Admin Issues Subject: RE: Multiple Domains in Exchange 2000 That was easy. In Exchange admin, Connections, IMS, on the routing tab I enabled "Reroute incoming SMTP mail...". Then by pressing "Add" I entered the domain, and chose the option "Should be rerouted to this domain" and entered the primary domain that I use for all email. I had about thirty domains on one server all routing this way. This works for inbound only. I found it very useful as we kept acquiring domains and I was able to ensure to management that the domains would work for inbound. If a certain user needed to send email with a different domain from the primary (different project or division) I could change it manually. If I could do this for Exchange 2000 without having to enter individual addresses to each user for each domain then I would be very happy. Hope this helps, Simon. -----Original Message----- From: Dimitri Limanovski [mailto:[EMAIL PROTECTED]] Posted At: 11 April 2002 17:48 Posted To: Exchange List Conversation: Multiple Domains in Exchange 2000 Subject: RE: Multiple Domains in Exchange 2000 Just curios: how did you achieve this in 5.5 without adding additional SMTP address? -----Original Message----- From: Simon Butler [mailto:[EMAIL PROTECTED]] Sent: Thursday, April 11, 2002 12:37 PM To: MS-Exchange Admin Issues Subject: Multiple Domains in Exchange 2000 Hello, In Exchange 5.5 I could have one domain mapped to another, so <username>@domaina.com would automatically go to <username>@domainb.com, without having to add the second domain to everyone's SMTP email address. Very useful when the company wanted all of their domains to work for inbound email and also meant I didn't have to modify every account each time a new one was bought. However despite lots of research I can't seem to find that feature on Exchange 2000. Am I missing something obvious? Thanks, Simon Butler. -- Simon Butler, SysAdmin Radiant Real-Time, Bracknell, UK [EMAIL PROTECTED] Tel: +44 (0)1344 742802 List Charter and FAQ at: http://www.sunbelt-software.com/exchange_list_charter.htm List Charter and FAQ at: http://www.sunbelt-software.com/exchange_list_charter.htm List Charter and FAQ at: http://www.sunbelt-software.com/exchange_list_charter.htm List Charter and FAQ at: http://www.sunbelt-software.com/exchange_list_charter.htm List Charter and FAQ at: http://www.sunbelt-software.com/exchange_list_charter.htm
