Hi Todd,
Thanks for your response.. it looks right to my eyes aswell, I was
wondering if there was an easy way to debug this kind of thing...
IE: is there a command to authenticate as a specific user and from am
IP address like -bh
Any improvements to the below would be appreciated,
acl_check_rcpt:
accept hosts = :
deny domains = +local_domains
local_parts = ^[.] : ^...@%!/|]
deny domains = !+local_domains
local_parts = ^[./|] : ^...@%!] : ^.*/\\.\\./
accept local_parts = postmaster
domains = +local_domains
# accept authenticated = *
# add_header = X-AuthenticatedID: $authenticated_id
# add_header = X-OriginalFromAdr: $sender_address
deny message = Reverse DNS lookup failed for host
$sender_host_address.
log_message = Reverse DNS lookup failed
domains = !+noreverse
hosts = !+relay_from_hosts
hosts = !+host_accept_relay
!authenticated = *
!verify = reverse_host_lookup
# require verify = sender
accept domains = +local_domains
endpass
verify = recipient
accept domains = +relay_to_domains
endpass
verify = recipient
deny message = $sender_host_address is not allowed to send
mail from $sender_address_domain
log_message = SPF check failed
hosts = !+relay_from_hosts
spf = fail
accept authenticated = *
add_header = X-AuthenticatedID: $authenticated_id
add_header = X-OriginalFromAdr: $sender_address
# deny message = relay not permitted
deny message = Access denied - $sender_host_address listed
by $dnslist_domain\n$dnslist_text
!authenticated = *
hosts = !+relay_from_hosts
dnslists = dnsbl.sorbs.net
deny log_message = match sbl-xbl.spamhaus.org
hosts = !+relay_from_hosts
!authenticated = *
dnslists = sbl-xbl.spamhaus.org
deny log_message = Access denied - $sender_host_address listed
by $dnslist_domain\n$dnslist_text
!authenticated = *
hosts = !+relay_from_hosts
dnslists = bl.spamcop.net
deny log_message = Access denied - $sender_host_address listed
by $dnslist_domain\n$dnslist_text
!authenticated = *
hosts = !+relay_from_hosts
dnslists = bl.spamcop.net
accept hosts = +relay_from_hosts
accept hosts = +host_accept_relay
accept authenticated = *
add_header = X-AuthenticatedID: $authenticated_id
add_header = X-OriginalFromAdr: $sender_address
deny message = relay not permitted
Kind Regards,
Jonathan Gilpin
Fluent Ltd
www.fluent.ltd.uk
On 21 Aug 2009, at 01:37, Todd Lyons wrote:
> On Wed, Aug 19, 2009 at 5:59 AM, Jonathan Gilpin<jonat...@fluent.ltd.uk
> > wrote:
>> Hi,
>>
>> I have the following in my configure file to block mail on a certain
>> blacklist. However, I want to allow the IP if the user is
>> authenticated.
>> However, it doesnt seem to be working...
>>
>> Is the syntax incorrect? should it be authenticated = !* ?
>>
>> deny message = Access denied - $sender_host_address listed
>> by $dnslist_domain\n$dnslist_text
>> !authenticated = *
>> hosts = !+relay_from_hosts
>> dnslists = dnsbl.sorbs.net
>
> It looks fine. I would say that you need to post the rest of your
> ACL's. With no further information, I would say that you are getting
> blocked somewhere else. Also, I'll state the obvious and make sure
> that you restart exim after you make changes to the exim.conf.
>
> --
> Regards... Todd
--
## List details at http://lists.exim.org/mailman/listinfo/exim-users
## Exim details at http://www.exim.org/
## Please use the Wiki with this list - http://wiki.exim.org/
