Aravind Sadagopan wrote:
>
> Hmmm..SIG11 problem..did you change any hardware or configuration ..
The only HW that changed between LM 6.1 and LM 7.1 is the CD driver.
I also installed LILO on the /partition instead of MBR because stupid
BIOS
will abort boot yelling "VIRUS!!".
I also did configure the sound card (same I never used under LM 6.1,
ensoniq 1371 or something like that..)
Finally, I turned on HD optimization this time
Does it means anything to you?
TIA,
Marco
> Marco Fioretti wrote:
>
> > Hello,
> >
> > I installed Linux Mandrake 7.1, and set it up to boot in runlevel 5.
> >
> > After 2/3 weeks almost without an itch, XDM has started crashing
> > 80 % of times, leaving the message copied below.
> >
> > Any idea? I haven't run gdb since I coudl not figure out the results
> >
> > myself, but if somebody is interest/willing to help, please tell me,
> >
> > and I'll run any test which is needed, and post the results.
> >
> > TIA,
> >
> > Marco Fioretti
> > ----------- xdm-errors.log
> > ----------------------------------------------
> >
> > XFree86 Version 3.3.6 / X Window System
> > (protocol Version 11, revision 0, vendor release 6300)
> > Release Date: January 8 2000
> > If the server is older than 6-12 months, or if your card is
> > newer
> > than the above date, look for a newer version before
> > reporting
> > problems. (see http://www.XFree86.Org/FAQ)
> > Operating System: Linux 2.2.14-1mdkmosix i686 [ELF]
> > Configured drivers:
> > SVGA: server for SVGA graphics adaptors (Patchlevel 0):
> > NV1, STG2000, RIVA 128, RIVA TNT, RIVA TNT2, RIVA ULTRA TNT2,
> > RIVA VANTA, RIVA ULTRA VANTA, RIVA INTEGRATED, GeForce 256,
> > GeForce DDR, Quadro, ET4000, ET4000W32, ET4000W32i,
> > ET4000W32i_rev_b,
> > ET4000W32i_rev_c, ET4000W32p, ET4000W32p_rev_a,
> > ET4000W32p_rev_b,
> > ET4000W32p_rev_c, ET4000W32p_rev_d, ET6000, ET6100, et3000,
> > pvga1,
> > wd90c00, wd90c10, wd90c30, wd90c24, wd90c31, wd90c33, gvga,
> > r128,
> > ati,
> > sis86c201, sis86c202, sis86c205, sis86c215, sis86c225,
> > sis5597,
> > sis5598, sis6326, sis530, sis620, sis300, sis630, sis540,
> > tvga8200lx,
> > tvga8800cs, tvga8900b, tvga8900c, tvga8900cl, tvga8900d,
> > tvga9000,
> > tvga9000i, tvga9100b, tvga9200cxr, tgui9400cxi, tgui9420,
> > tgui9420dgi,
> > tgui9430dgi, tgui9440agi, cyber9320, tgui9660, tgui9680,
> > tgui9682,
> > tgui9685, cyber9382, cyber9385, cyber9388, cyber9397,
> > cyber9520,
> > cyber9525, 3dimage975, 3dimage985, cyber9397dvd, blade3d,
> > cyberblade,
> > clgd5420, clgd5422, clgd5424, clgd5426, clgd5428, clgd5429,
> > clgd5430,
> > clgd5434, clgd5436, clgd5446, clgd5480, clgd5462, clgd5464,
> > clgd5465,
> > clgd6205, clgd6215, clgd6225, clgd6235, clgd7541, clgd7542,
> > clgd7543,
> > clgd7548, clgd7555, clgd7556, ncr77c22, ncr77c22e, cpq_avga,
> > mga2064w,
> > mga1064sg, mga2164w, mga2164w AGP, mgag200, mgag100, mgag400,
> > oti067,
> > oti077, oti087, oti037c, al2101, ali2228, ali2301, ali2302,
> > ali2308,
> > ali2401, cl6410, cl6412, cl6420, cl6440, video7, ark1000vl,
> > ark1000pv,
> > ark2000pv, ark2000mt, mx, realtek, s3_savage, s3_virge,
> > AP6422,
> > AT24,
> > AT3D, s3_svga, NM2070, NM2090, NM2093, NM2097, NM2160, NM2200,
> >
> > ct65520, ct65525, ct65530, ct65535, ct65540, ct65545, ct65546,
> >
> > ct65548, ct65550, ct65554, ct65555, ct68554, ct69000, ct64200,
> >
> > ct64300, mediagx, V1000, V2100, V2200, p9100, spc8110, i740,
> > i740_pci,
> > Voodoo Banshee, Voodoo3, i810, i810-dc100, i810e, smi, generic
> >
> > (using VT number 7)
> >
> > XF86Config: /etc/X11/XF86Config
> > (**) stands for supplied, (--) stands for probed/default values
> > (**) XKB: keycodes: "xfree86"
> > (**) XKB: types: "default"
> > (**) XKB: compat: "default"
> > (**) XKB: symbols: "us(pc105)"
> > (**) XKB: geometry: "pc"
> > (**) XKB: rules: "xfree86"
> > (**) XKB: model: "pc105"
> > (**) XKB: layout: "us"
> > (**) Mouse: type: PS/2, device: /dev/psaux, buttons: 3
> > (**) SVGA: Graphics device ID: "Matrox Millennium G200 4MB"
> > (**) SVGA: Monitor ID: "Generic|Multi-frequency that can do
> > 1280x1024 at
> > 60 Hz"
> > (--) SVGA: Mode "640x480" needs hsync freq of 32.10 kHz. Deleted.
> > (--) SVGA: Mode "640x480" needs hsync freq of 38.60 kHz. Deleted.
> > (--) SVGA: Mode "640x480" needs hsync freq of 37.50 kHz. Deleted.
> > (--) SVGA: Mode "800x600" needs hsync freq of 35.16 kHz. Deleted.
> > (--) SVGA: Mode "800x600" needs hsync freq of 37.88 kHz. Deleted.
> > (--) SVGA: Mode "800x600" needs hsync freq of 46.88 kHz. Deleted.
> > (--) SVGA: Mode "800x600" needs hsync freq of 53.67 kHz. Deleted.
> > (--) SVGA: Mode "1024x768" needs hsync freq of 48.36 kHz. Deleted.
> > (--) SVGA: Mode "1024x768" needs hsync freq of 56.48 kHz. Deleted.
> > (--) SVGA: Mode "1024x768" needs hsync freq of 60.02 kHz. Deleted.
> > (--) SVGA: Mode "1280x1024" needs hsync freq of 79.98 kHz. Deleted.
> > (--) SVGA: Mode "640x400" needs hsync freq of 31.47 kHz. Deleted.
> > (--) SVGA: Mode "640x480" needs hsync freq of 31.47 kHz. Deleted.
> > (--) SVGA: Mode "800x600" needs hsync freq of 35.16 kHz. Deleted.
> > (--) SVGA: Mode "1024x768" needs hsync freq of 35.52 kHz. Deleted.
> > (--) SVGA: Mode "640x400" needs hsync freq of 37.86 kHz. Deleted.
> > (--) SVGA: Mode "640x480" needs hsync freq of 36.46 kHz. Deleted.
> > (--) SVGA: Mode "640x480" needs hsync freq of 37.50 kHz. Deleted.
> > (--) SVGA: Mode "800x600" needs hsync freq of 37.88 kHz. Deleted.
> > (--) SVGA: Mode "640x480" needs hsync freq of 43.27 kHz. Deleted.
> > (--) SVGA: Mode "1152x864" needs hsync freq of 43.92 kHz. Deleted.
> > (--) SVGA: Mode "800x600" needs hsync freq of 48.08 kHz. Deleted.
> > (--) SVGA: Mode "1024x768" needs hsync freq of 48.36 kHz. Deleted.
> > (--) SVGA: Mode "640x480" needs hsync freq of 53.01 kHz. Deleted.
> > (--) SVGA: Mode "1152x864" needs hsync freq of 53.51 kHz. Deleted.
> > (--) SVGA: Mode "800x600" needs hsync freq of 55.84 kHz. Deleted.
> > (--) SVGA: Mode "1024x768" needs hsync freq of 56.48 kHz. Deleted.
> > (--) SVGA: Mode "1280x1024" needs hsync freq of 51.02 kHz. Deleted.
> > (--) SVGA: Mode "800x600" needs vert refresh rate of 100.03 Hz.
> > Deleted.
> > (--) SVGA: Mode "1280x1024" needs vert refresh rate of 60.96 Hz.
> > Deleted.
> > (--) SVGA: Mode "1024x768" needs vert refresh rate of 85.45 Hz.
> > Deleted.
> > (--) SVGA: Mode "1152x864" needs vert refresh rate of 78.06 Hz.
> > Deleted.
> > (--) SVGA: Mode "1280x1024" needs hsync freq of 74.59 kHz. Deleted.
> > (--) SVGA: Mode "1600x1200" needs hsync freq of 75.00 kHz. Deleted.
> > (--) SVGA: Mode "1152x864" needs hsync freq of 76.01 kHz. Deleted.
> > (--) SVGA: Mode "1280x1024" needs hsync freq of 78.86 kHz. Deleted.
> > (--) SVGA: Mode "1024x768" needs hsync freq of 80.21 kHz. Deleted.
> > (--) SVGA: Mode "1280x1024" needs hsync freq of 81.13 kHz. Deleted.
> > (--) SVGA: Mode "1600x1200" needs hsync freq of 87.50 kHz. Deleted.
> > (--) SVGA: Mode "1152x864" needs hsync freq of 89.62 kHz. Deleted.
> > (--) SVGA: Mode "1280x1024" needs hsync freq of 91.15 kHz. Deleted.
> > (--) SVGA: Mode "1600x1200" needs hsync freq of 93.75 kHz. Deleted.
> > (--) SVGA: Mode "1600x1200" needs hsync freq of 105.77 kHz. Deleted.
> >
> > (--) SVGA: Mode "1280x1024" needs hsync freq of 107.16 kHz. Deleted.
> >
> > (--) SVGA: Mode "1800X1440" needs hsync freq of 96.15 kHz. Deleted.
> > (--) SVGA: Mode "1800X1440" needs hsync freq of 104.52 kHz. Deleted.
> >
> > (--) SVGA: Mode "512x384" needs hsync freq of 31.50 kHz. Deleted.
> > (--) SVGA: Mode "512x384" needs hsync freq of 34.38 kHz. Deleted.
> > (--) SVGA: Mode "320x200" needs hsync freq of 31.47 kHz. Deleted.
> > (--) SVGA: Mode "320x240" needs hsync freq of 31.47 kHz. Deleted.
> > (--) SVGA: Mode "320x240" needs hsync freq of 39.38 kHz. Deleted.
> > (--) SVGA: Mode "400x300" needs hsync freq of 35.16 kHz. Deleted.
> > (--) SVGA: Mode "400x300" needs hsync freq of 37.88 kHz. Deleted.
> > (--) SVGA: Mode "400x300" needs hsync freq of 48.08 kHz. Deleted.
> > (--) SVGA: Mode "480x300" needs hsync freq of 35.16 kHz. Deleted.
> > (--) SVGA: Mode "480x300" needs hsync freq of 37.80 kHz. Deleted.
> > (--) SVGA: Mode "480x300" needs hsync freq of 39.56 kHz. Deleted.
> > (--) SVGA: Mode "480x300" needs hsync freq of 48.00 kHz. Deleted.
> > (**) FontPath set to "unix/:-1"
> > (--) SVGA: PCI: Matrox MGA G200 AGP rev 1, Memory @ 0xe8000000,
> > 0xe4000000
> > (--) SVGA: Linear framebuffer at 0xE8000000
> > (--) SVGA: MMIO registers at 0xE4000000
> > (--) SVGA: Video BIOS info block at 0x000c7540
> > (--) SVGA: Found and verified enhanced Video BIOS info block
> > (--) SVGA: detected an SGRAM card
> > (--) SVGA: chipset: mgag200
> > (**) SVGA: videoram: 8192k
> > (**) SVGA: Option "dac_8_bit"
> > (**) SVGA: Option "sync_on_green"
> > (**) SVGA: Option "power_saver"
> > (**) SVGA: Using 32 bpp, Depth 24, Color weight: 888
> > (--) SVGA: Maximum allowed dot-clock: 250.000 MHz
> > (--) SVGA: There is no mode definition named "1280x1024"
> > (--) SVGA: Removing mode "1280x1024" from list of valid modes.
> > (--) SVGA: There is no mode definition named "1152x864"
> > (--) SVGA: Removing mode "1152x864" from list of valid modes.
> > (**) SVGA: Mode "1152x900": mode clock = 104.348
> > (**) SVGA: Mode "1152x900a": mode clock = 104.348
> > (**) SVGA: Mode "1152x900b": mode clock = 104.348
> > (**) SVGA: Mode "1152x900c": mode clock = 94.500
> > (**) SVGA: Mode "1152x900d": mode clock = 104.348
> > (--) SVGA: There is no mode definition named "1024x768"
> > (--) SVGA: Removing mode "1024x768" from list of valid modes.
> > (--) SVGA: There is no mode definition named "800x600"
> > (--) SVGA: Removing mode "800x600" from list of valid modes.
> > (--) SVGA: There is no mode definition named "640x480"
> > (--) SVGA: Removing mode "640x480" from list of valid modes.
> > (--) SVGA: Virtual resolution set to 1152x900
> > (--) SVGA: SpeedUp code selection modified because virtualX != 1024
> > (--) SVGA: Using hardware cursor
> > (**) SVGA: sync on green
> > (--) SVGA: PLL reference freq: 27.050 MHz
> > (--) SVGA: Read OPTION 0x4007cd21
> > (--) SVGA: Using XAA (XFree86 Acceleration Architecture)
> > (--) SVGA: XAA: Solid filled rectangles
> > (--) SVGA: XAA: Screen-to-screen copy
> > (--) SVGA: XAA: 8x8 color expand pattern fill
> > (--) SVGA: XAA: CPU to screen color expansion (TE/NonTE imagetext,
> > TE/NonTE polytext)
> > (--) SVGA: XAA: Using 9 128x128 areas for pixmap caching
> > (--) SVGA: XAA: Caching tiles and stipples
> > (--) SVGA: XAA: General lines and segments
> > (--) SVGA: XAA: Dashed lines and segments
> > Caught signal 11.
> >
> > Server aborting...
> >
> > eip: 001fa244 eflags: 00013206
> > eax: 60290c84 ebx: 00292800 ecx: 00290c78 edx: 00000000
> > esi: 083677a8 edi: 00000000 ebp: bffff0ec esp: bffff0c4
> > Stack: ffffffff 083677a8 bffff11c 082aab5b 08367828 00000000
> > bffff51c
> > 082a54a7
> > 00000000 00fffb28 bffff51c 082a553c 083677a8 00000000
> > 0000007f
> > bffffad0
> > bffffad0 bffffb28 bffff590 0834dab0 bffff590 bffffb28
> > 7273752f
> > 3131582f
> > 6c2f3652 582f6269 782f3131 632f626b 69706d6f 2f64656c
> > 76726573
> > 302d7265
> > Call Trace: 082aab5b 082a54a7 082a553c 0828e9a5 081c1cc8 08291a87
> > 0828f19d
> > 08187a64 08187d14 08187d38 081878e9 08187d80 08196d0e
> > 0817683d
> > 08176804
> > 081ab09f 081aaf68 082cda14 0807db10 0807db31 081aad10
> > 082cda14
> > 0807db10
> > Code: 3b 30 74 0f c7 06 00 00 00 00 83 c4 f4 56 e8 75 e6 fc ff 89
> >
> > Please forward information about this crash to [EMAIL PROTECTED]
> > including the _full_ output of the X server.
> >
> > To analyse the crash dump, please type
> >
> > gdb /etc/X11/X //core
> > where
> >
> > and include this output in your report. Thanks!
> >
> > X connection to :0.0 broken (explicit kill or server shutdown).
> > _X11TransSocketUNIXConnect: Can't connect: errno = 111
> > _X11TransSocketUNIXConnect: Can't connect: errno = 111
> > _X11TransSocketUNIXConnect: Can't connect: errno = 111
> > _X11TransSocketUNIXConnect: Can't connect: errno = 111
> > _X11TransSocketUNIXConnect: Can't connect: errno = 111
> > _X11TransSocketUNIXConnect: Can't connect: errno = 111
> > _X11TransSocketUNIXConnect: Can't connect: errno = 111
> > _X11TransSocketUNIXConnect: Can't connect: errno = 111
> > _X11TransSocketUNIXConnect: Can't connect: errno = 111
> > switching back to runlevel 3
> >
> >
> > ------------------------------------------------------------------------
> >
> > Keep in touch with http://mandrakeforum.com:
> > Subscribe the "[EMAIL PROTECTED]" mailing list.
>
> --
> Living on Earth is expensive, but it does include a free trip
> round the sun
>
>
>
> ---------------------------------------------------------------
> Keep in touch with http://mandrakeforum.com:
> Subscribe the "[EMAIL PROTECTED]" mailing list.
Keep in touch with http://mandrakeforum.com:
Subscribe the "[EMAIL PROTECTED]" mailing list.
