Best article ever read on this list, hehe...
Don't feed the trolls ! ;-)
cu
another J
> -----Original Message-----
> From: "J" [mailto:[EMAIL PROTECTED]]
> Sent: Wednesday, July 11, 2001 9:39 AM
> To: [EMAIL PROTECTED]
> Subject: RE: Hacking FW-1 programs
>
>
> Well, for the determined of spirit, I offer the following advice:
>
> A firewall is a difficult thing to "get through." First off,
> most good ones
> are made of heat-molded concrete with a ludicrously high
> grain-count, so
> just the outer layer is going to be hard to get through. See,
> the challenge
> is to generate enough heat in one concentrated region so the
> fine-grain of
> the concrete shell begin to melt together into an oily
> sludge. This is a
> sign things are going well. Additionally, the sludge will
> help keep the
> drill-bits cool.
>
> Now, at this point, many seasoned professionals will recommend
> diamond-tipped drill bits. I however, being a beliver in
> modern technology,
> prefer the tungsten-carbide bits. While you do replace more
> of them during
> an operation, I find they wear predictably and provide a
> better conduit-area
> for your needs.
>
> Next, you'll have to contend with a re-enforced
> aluminium-carbon sink-plate.
> The reason for this layer is to distribute the heat from the
> outer walls of
> the firewall to something else; in most cases, foundation beams in the
> building, sending the heat into the surrounding foundation. The
> compressed-aluminium will get your tungsten bits very, very
> hot. I'd also
> recommend wearing ear protection at this point. Be aware that
> dogs will
> start barking for miles around when you hit this layer.
>
> Once through the heat-sink, you're faced with one of two typical
> possibilities: ceramic interior or polycarbonate-platter
> walls. If you find
> ceramic, you're in luck, because the ceramic will withstand
> the pressure of
> the explosives you'll be using later. The platters, however,
> are another
> ball game. All I'll say is: bring a DustBuster!
>
> Providing you've come up 7's on the ceramic, you should go
> ahead and stuff
> as much plastic-explosive as you can in the hole you've
> drilled (which was
> 3" diameter, right?). Most experts, and I concur with them
> this time, prefer
> to use Primacord as the detonation device. I've heard of a
> few nice tricks
> with wrapping the Prima around the firewall to help "cut" the
> outer concrete
> shell and shatter the wall itself.
>
> Step 10: Blow up firewall.
>
> If you followed the above steps, you should now have, after the dust
> settles, a pathway through the firewall into the inner-room
> that you should
> be able to walk or crouch through. Grab your spool of CAT5
> cable, and tow a
> lead behind you as you walk through your new hole in the
> firewall. Once
> inside, crimp the end of the cable you're holding with a standard RJ45
> connector. Take note of the order the colored-wires are in:
> you'll need to
> make the other end the same way. Plug into edge router or switch.
>
> Walk back to spool. Count out about twenty feet of cable, and
> cut. Crimp
> another RJ45 connector on this end, taking care to align the little
> colored-wires in the same order as the first end, and plug into your
> computer.
>
> I guarantee the firewall will not interrupt any traffic on your line.
>
> Hope this helps,
>
>
> J
>
>
>
> Cheers!
>
> -----Original Message-----
> From: [EMAIL PROTECTED]
> [mailto:[EMAIL PROTECTED]]On Behalf Of MNR. E DE BEER
> Sent: Tuesday, July 10, 2001 8:00 PM
> To: [EMAIL PROTECTED]
> Subject: Hacking FW-1 programs
>
>
> Are there any Hack software that I can use to get access to a
> Firewall-1 without using Inetkey (username and password)?
> Where can I find this softwhere?
> _______________________________________________
> Firewalls mailing list
> [EMAIL PROTECTED]
> http://lists.gnac.net/mailman/listinfo/firewalls
>
> -----Original Message-----
> From: [EMAIL PROTECTED]
> [mailto:[EMAIL PROTECTED]]On Behalf Of MNR. E DE BEER
> Sent: Tuesday, July 10, 2001 8:00 PM
> To: [EMAIL PROTECTED]
> Subject: Hacking FW-1 programs
>
>
> Are there any Hack software that I can use to get access to a
> Firewall-1 without using Inetkey (username and password)?
> Where can I find this softwhere?
> _______________________________________________
> Firewalls mailing list
> [EMAIL PROTECTED]
> http://lists.gnac.net/mailman/listinfo/firewalls
>
> _______________________________________________
> Firewalls mailing list
> [EMAIL PROTECTED]
> http://lists.gnac.net/mailman/listinfo/firewalls
>
_______________________________________________
Firewalls mailing list
[EMAIL PROTECTED]
http://lists.gnac.net/mailman/listinfo/firewalls
