Thanks to the traces captured by Martin Roth, and confirmed by tests and analysis by Joshua Zarr, we can now use both target chips on the Dediprog SF100.
Signed-off-by: Stefan Tauner <[email protected]> --- dediprog.c | 51 +++++++++++++++++++++++++++++++++++++++------------ flashrom.8 | 12 ++++++++++++ 2 files changed, 51 insertions(+), 12 deletions(-) diff --git a/dediprog.c b/dediprog.c index ae86810..2cf8949 100644 --- a/dediprog.c +++ b/dediprog.c @@ -560,19 +560,21 @@ static int dediprog_command_b(void) } #endif -/* Command C is only sent after dediprog_check_devicestring, but not after every +/* Command Chip Select is only sent after dediprog_check_devicestring, but not after every * invocation of dediprog_check_devicestring. It is only sent after the first * dediprog_command_a(); dediprog_check_devicestring() sequence in each session. - * I'm tempted to call this one start_SPI_engine or finish_init. + * Bit #1 of the value changes the chip select: 0 is target 1, 1 is target 2 and parameter target can be 1 or 2 + * respectively. We don't know how to encode "3, Socket" and "0, reference card" yet. */ -static int dediprog_command_c(void) +static int dediprog_chip_select(int target) { int ret; - - ret = usb_control_msg(dediprog_handle, 0x42, 0x4, 0x0, 0x0, NULL, + uint16_t value = ((target - 1) & 1) << 1; + msg_pdbg("Selecting target chip %i\n", target); + ret = usb_control_msg(dediprog_handle, 0x42, 0x4, value, 0x0, NULL, 0x0, DEFAULT_TIMEOUT); if (ret != 0x0) { - msg_perr("Command C failed (%s)!\n", usb_strerror()); + msg_perr("Command Chip Select failed (%s)!\n", usb_strerror()); return 1; } return 0; @@ -722,7 +724,7 @@ static int parse_voltage(char *voltage) return millivolt; } -static int dediprog_setup(void) +static int dediprog_setup(long target) { /* URB 6. Command A. */ if (dediprog_command_a()) { @@ -737,8 +739,8 @@ static int dediprog_setup(void) if (dediprog_check_devicestring()) { return 1; } - /* URB 10. Command C. */ - if (dediprog_command_c()) { + /* URB 10. Command Chip Select */ + if (dediprog_chip_select(target)) { return 1; } return 0; @@ -785,10 +787,11 @@ static int dediprog_shutdown(void *data) int dediprog_init(void) { struct usb_device *dev; - char *voltage, *device, *spispeed; + char *voltage, *device, *spispeed, *target_str; int spispeed_idx = 2; int millivolt = 3500; long usedevice = 0; + long target = 1; int i, ret; msg_pspew("%s\n", __func__); @@ -841,6 +844,30 @@ int dediprog_init(void) } free(device); + target_str = extract_programmer_param("target"); + if (target_str) { + char *target_suffix; + errno = 0; + target = strtol(target_str, &target_suffix, 10); + if (errno != 0 || target_str == target_suffix) { + msg_perr("Error: Could not convert 'target'.\n"); + free(target_str); + return 1; + } + if (target < 1 || target > 2) { + msg_perr("Error: Value for 'target' is out of range.\n"); + free(target_str); + return 1; + } + if (strlen(target_suffix) > 0) { + msg_perr("Error: Garbage following 'target' value.\n"); + free(target_str); + return 1; + } + msg_pinfo("Using target %li.\n", target); + } + free(target_str); + /* Here comes the USB stuff. */ usb_init(); usb_find_busses(); @@ -877,13 +904,13 @@ int dediprog_init(void) dediprog_set_leds(PASS_ON|BUSY_ON|ERROR_ON); /* Perform basic setup. */ - if (dediprog_setup()) { + if (dediprog_setup(target)) { dediprog_set_leds(PASS_OFF|BUSY_OFF|ERROR_ON); return 1; } /* After setting voltage and speed, perform setup again. */ - if (dediprog_set_spi_voltage(0) || dediprog_set_spi_speed(spispeed_idx) || dediprog_setup()) { + if (dediprog_set_spi_voltage(0) || dediprog_set_spi_speed(spispeed_idx) || dediprog_setup(target)) { dediprog_set_leds(PASS_OFF|BUSY_OFF|ERROR_ON); return 1; } diff --git a/flashrom.8 b/flashrom.8 index e4e2b94..98f71d2 100644 --- a/flashrom.8 +++ b/flashrom.8 @@ -694,6 +694,18 @@ where can be .BR 375k ", " 750k ", " 1.5M ", " 2.18M ", " 3M ", " 8M ", " 12M " or " 24M (in Hz). The default is a frequency of 12 MHz. +.sp +An optional +.B target +parameter specifies which target chip should be used. Syntax is +.sp +.B " flashrom \-p dediprog:target=value" +.sp +where +.B value +can be +.BR 1 " or " 2 +to select target chip 1 or 2 repectively. The default is target chip 1. .SS .BR "rayer_spi " programmer The default I/O base address used for the parallel port is 0x378 and you can use -- Kind regards, Stefan Tauner _______________________________________________ flashrom mailing list [email protected] http://www.flashrom.org/mailman/listinfo/flashrom
