Meh, no matter..
Exported a Clean DB, copied my TX Profiles into it from the "broken" DB and all
is good now.
The section that seemed to causing the issue in the "broken" one was:
<BandStack>
<BandName>60M</BandName>
<Mode>USB</Mode>
<Filter>F6</Filter>
<Freq>5.349954</Freq>
</BandStack>
And in the Clean it was this....
<BandStack>
<BandName>60M</BandName>
<Mode>USB</Mode>
<Filter>F6</Filter>
<Freq>5.3715</Freq>
</BandStack>
I copied that section to my broken DB and it fixed the issue. But I decided
to create a new one -
just in case.
This whole thread is probably of no use to anyone - as it was something I
probably did. But did
not want to leave it hanging.
--
Richard A Clafton | the brITish guy | W5\G7EIX
RIROC - Hosting - Development - Technology
http://www.riroc.com | [email protected]
"Jack of all trades, master of none, though often better than the master of
one."
-----Original Message-----
From: [email protected]
[mailto:[email protected]] On Behalf Of
Richard Clafton
Sent: Wednesday, September 05, 2012 4:09 PM
To: 'Ernest Garcia'; [email protected]; 'Flexedge'
Subject: Re: [Flexradio] [FlexEdge] PowerSDR 2.4.4 - 60m Band Channels wrong?
Most strange. I just backed up the DB, did a factory reset and started up
again....and the
Channels work fine. If I import the exported DB, they mess up again.
Compared the Factory Reset
DB and my exported DB for BANDTEXT and they are the same...
Strange....
--
Richard A Clafton | the brITish guy | W5\G7EIX RIROC - Hosting - Development -
Technology
http://www.riroc.com | [email protected] "Jack of all trades, master of none,
though often better
than the master of one."
-----Original Message-----
From: Ernest Garcia [mailto:[email protected]]
Sent: Wednesday, September 05, 2012 3:59 PM
To: [email protected]; [email protected]; Flexedge
Subject: [SPAM?] RE: [FlexEdge] PowerSDR 2.4.4 - 60m Band Channels wrong?
Guess you on this boat by yourself.
I checked my setup and they all fall in the 60 meter band.
Ernest -W4EG
> From: [email protected]
> To: [email protected]; [email protected]
> Date: Wed, 5 Sep 2012 15:42:36 -0500
> Subject: [FlexEdge] PowerSDR 2.4.4 - 60m Band Channels wrong?
>
> Noticed something strange. If I click on the 60m BAND button to cycle
> through the channels, it starts on:
>
> 5.349.954 (GEN COV)
> 5.346.50 (CH2)
> 5.357.00 (CH3)
>
> And then back to 5.349.954
>
> Is this just me? This is a clean install.
>
> US radio in the US
>
> --
> Richard A Clafton | the brITish guy | W5\G7EIX RIROC - Hosting -
> Development - Technology http://www.riroc.com | [email protected]
> "Jack of all trades, master of none, though often better than the master of
> one."
>
>
>
>
>
> _______________________________________________
> Flexedge mailing list
> [email protected]
> http://mail.flex-radio.biz/mailman/listinfo/flexedge_flex-radio.biz
> This is the FlexRadio Systems e-mail Reflector called FlexEdge. It is
> used for posting topics
related to SDR software innovation and other technical SDR topics.
_______________________________________________
FlexRadio Systems Mailing List
[email protected]
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/
_______________________________________________
Flexedge mailing list
[email protected]
http://mail.flex-radio.biz/mailman/listinfo/flexedge_flex-radio.biz
This is the FlexRadio Systems e-mail Reflector called FlexEdge. It is used for
posting topics related to SDR software innovation and other technical SDR
topics.
