We can add a reverse function pretty easily. I'll see what I can do to fit that in there. The panning has no effect on TX. Just on RX.
Eric Wachsmann FlexRadio Systems > -----Original Message----- > From: Duane - N9DG [mailto:[EMAIL PROTECTED] > Sent: Thursday, September 21, 2006 10:47 AM > To: Eric Wachsmann; 'Jerald Jones'; [EMAIL PROTECTED]; [EMAIL PROTECTED] > radio.biz > Subject: RE: [Flexradio] 683 Sub RX Sliders > > > I don't doubt that it is correct in the software. It would > just be nice little enhnacement to have an option to make > left/right backwards in sofware vs. having to do it in HW. > > I still hope to put the Audiophile 192 to use in TX so > wouldn't swapping the cables trip up the I/Q sense when going > into TX. Or is the speaker/QSE (RX/TX) relay switching no > longer done? Disclaimer: struggling to remember the exact > physical connection paths for TX since I'm not near the radio > or schematics to figure it out. So I maybe totally wet on > this one...;). > > Duane > N9DG > > --- Eric Wachsmann <[EMAIL PROTECTED]> wrote: > > > There's at least one easy solution if you are using one of > > our recommended > > soundcards....just swap the output 1&2 cables at the > > soundcard. ;) I'll > > double check that the source has the correct orientation, > > but I do believe > > it is correct. > > > > > > Eric Wachsmann > > FlexRadio Systems > > > > > -----Original Message----- > > > From: [EMAIL PROTECTED] > > [mailto:[EMAIL PROTECTED] > > > radio.biz] On Behalf Of Jerald Jones > > > Sent: Thursday, September 21, 2006 9:38 AM > > > To: Duane - N9DG; [EMAIL PROTECTED]; > > flexradio@flex-radio.biz > > > Subject: Re: [Flexradio] 683 Sub RX Sliders > > > > > > My pan sliders for the SubRX are also reversed. Are most > > everyones > > > reversed > > > or is this just a few of us? > > > > > > Jerry WK0J > > > > > > ----- Original Message ----- > > > From: "Duane - N9DG" <[EMAIL PROTECTED]> > > > To: <[EMAIL PROTECTED]>; <flexradio@flex-radio.biz> > > > Sent: Thursday, September 21, 2006 8:40 AM > > > Subject: Re: [Flexradio] 683 Sub RX Sliders > > > > > > > > > > > > > > When I was playing 683 myself last night I was > > wondering the > > > > very same thing. The physical layout of my speakers is > > such > > > > that the "left" one is the only one that I can actually > > move > > > > to be on my right (cable limitations). > > > > > > > > Also while playing with 683 I was once again pondering > > how > > > > could settings such as volume and "RF Gain" be > > integrated > > > > directly into the panadapter window. Perhaps sliders > > > > superimposed over the filter bar for each receiver. > > Probably > > > > not something to pursue with the existing console but > > should > > > > definitely be thought about for the new console(s). > > > > > > > > Duane > > > > N9DG > > > > > > > > > > > > > > > > > > > > --- "[EMAIL PROTECTED]" <[EMAIL PROTECTED]> wrote: > > > > > > > >> This one may sound stupid ... any way to reverse the > > main & > > > >> sub pan > > > >> sliders? Seems my rack mount computer is far to the > > left of > > > >> the operator > > > >> station ... the close powered speaker is left and the > > slave > > > >> to the far > > > >> right ... so the sliders have a reverse effect! > > > >> > > > >> I guess I could implment the hardware solution and go > > cut > > > >> the stereo plug > > > >> off the speakers and reverse the wiring! > > > >> > > > >> VE3KH > > > > > > > __________________________________________________ > Do You Yahoo!? > Tired of spam? Yahoo! Mail has the best spam protection around > http://mail.yahoo.com _______________________________________________ FlexRadio mailing list FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archive Link: http://www.mail-archive.com/flexradio%40flex-radio.biz/ FlexRadio Homepage: http://www.flex-radio.com