That is correct. For now, it is either/or on the microphone vs. VAC. I expect that will change though.
Eric Wachsmann FlexRadio Systems > -----Original Message----- > From: Steve Kallal [mailto:[EMAIL PROTECTED] > Sent: Wednesday, December 05, 2007 11:32 AM > To: 'Eric Wachsmann'; flexradio@flex-radio.biz > Subject: RE: [Flexradio] CTCSS tones with PowerSDR? > > Eric, > > Thanks! > > OK, I'll contact Bob and Frank off the reflector. Maybe Team Speak is a > good > resource too. > > I tried VAC with SSB and found that it disables the microphone input. VAC > is > a dead end, at least in its current implementation. > > I will wait before getting an SVN branch. It may be too difficult. I am > not > sure how accurately I can generate the tones. They are in tenths of Hz. I > do > know I can set the volume level easily. > > 73, > > Steve N6VL > > -----Original Message----- > From: Eric Wachsmann [mailto:[EMAIL PROTECTED] > Sent: Wednesday, December 05, 2007 9:11 AM > To: 'Steve Kallal'; flexradio@flex-radio.biz > Subject: RE: [Flexradio] CTCSS tones with PowerSDR? > > Steve, > > We would be more than happy to create a branch on SVN for you to play > with. > In order to get your work into the main branch though, I'd suggest working > with our DSP code gurus Bob McGwier, N4HY and Frank Brickle, AB2KT. They > can probably help clarify where in the DSP chain to put the tone > generation. > > > Eric Wachsmann > FlexRadio Systems > > > -----Original Message----- > > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] > > radio.biz] On Behalf Of Steve Kallal > > Sent: Wednesday, December 05, 2007 11:00 AM > > To: flexradio@flex-radio.biz > > Subject: [Flexradio] CTCSS tones with PowerSDR? > > > > The question of CTCSS has been posed on this reflector once before. > > Tim W4TME, came up with a CTCSS software solution at > > http://comtekk.us/tone-remote-console.htm, but offered no solution on > > how to integrate it with PowerSDR. I am willing to code a solution if > > I can get some guidance on integrating it into PowerSDR. I found some > > source code for generating code, a few months ago, in the .NET > > Framework. I was working on a code practice program and never finished > > it. I need to know how to integrate it into PowerSDR. Ken N9VV, had > > suggested VAC. That could be a solution, but I am not sure if VAC > > audio will mix with microphone audio. The 5000A mixer allows only one > > input. > > > > There are few 6 meter repeaters locally. Also 10 meter FM used to be > > pretty hot during sunspot peaks. I thought it would be neat to try > > repeaters with the 5000A. > > > > I realize a lot of fires are being put out right now. I have a partial > > solution for CTCSS. I need to know how to tie it into PowerSDR. > > > > 73, > > > > Steve N6VL > > > > -------------- next part -------------- An HTML attachment was > > scrubbed... > > URL: http://mail.flex-radio.biz/pipermail/flexradio_flex- > > radio.biz/attachments/20071205/fc7094d3/attachment.html > > _______________________________________________ > > FlexRadio mailing list > > FlexRadio@flex-radio.biz > > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz > > Archive Link: http://www.mail-archive.com/flexradio%40flex-radio.biz/ > > FlexRadio Knowledge Base: http://kb.flex-radio.com/ FlexRadio > > Homepage: http://www.flex-radio.com/ > _______________________________________________ FlexRadio mailing list FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archive Link: http://www.mail-archive.com/flexradio%40flex-radio.biz/ FlexRadio Knowledge Base: http://kb.flex-radio.com/ FlexRadio Homepage: http://www.flex-radio.com/