There are not any controls. What you see displayed is signal strength not audio gain.
Turn down the AGC-T gain and turn up the AF gain to minimize the signal strength and to still be able to hear the signal -Tim -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of [EMAIL PROTECTED] Sent: Sunday, September 07, 2008 4:35 AM To: Dennis Petrich; Flex-Radio E-Mail Reflector Subject: Re: [Flexradio] PowerSDR 1.14.0 question Oeps Dennis, I read pana.. and expected panafal, asume it was late.... I see no vertical controls for the scopemode Some for the wishlist? 73 peter groeten Peter website http://www.homepages.hetnet.nl/~petervn/ <https://netmail.hetnet.nl/exchweb/bin/redir.asp?URL=https://netmail.hetnet.nl/exchweb/bin/redir.asp?URL=http://www.homepages.hetnet.nl/~petervn/> petervn-at-hetnet-nl pa0pvn-at-hetnet-nl pa0pvn-at-amsat-org only large files: pa0pvn-at-gmail-com There are 10 kind of people, those who can count to 1010 on their fingers, and those who count to 1111111111. ________________________________ Van: Dennis Petrich [mailto:[EMAIL PROTECTED] Verzonden: zo 7-9-2008 2:37 Aan: [EMAIL PROTECTED] Onderwerp: Re: [Flexradio] PowerSDR 1.14.0 question I don't undertand Peter. That is for the waterfall? My problem is the vertical gain of the SCOPE. But, I tried varing the low and high levels for the waterfall and they had no effect. Thanks anyway, or , do I still not understand? Ciao, Dennis ________________________________ Van: [EMAIL PROTECTED] Verzonden: za 6-9-2008 21:46 Aan: Dennis Petrich; Flex-Radio E-Mail Reflector Onderwerp: RE: [Flexradio] PowerSDR 1.14.0 question Setup -> Display -> - Spectrum Grid - Waterfall Set Low and High levels Hope that helps 73 peter pa0pvn groeten Peter website http://www.homepages.hetnet.nl/~petervn/ <https://netmail.hetnet.nl/exchweb/bin/redir.asp?URL=http://www.homepages.hetnet.nl/~petervn/> petervn-at-hetnet-nl pa0pvn-at-hetnet-nl pa0pvn-at-amsat-org only large files: pa0pvn-at-gmail-com There are 10 kind of people, those who can count to 1010 on their fingers, and those who count to 1111111111. ________________________________ Van: [EMAIL PROTECTED] namens Dennis Petrich Verzonden: za 6-9-2008 19:35 Aan: Flex-Radio E-Mail Reflector Onderwerp: [Flexradio] PowerSDR 1.14.0 question Hello guys, I just love the new scope and "Panascope" feature!!! The display looks just like a monitor scope.... My question is, how can I turn the scope vertical gain down without effecting the receivers gain??? The vertical gain is so much it goes off the screen or in Panascope mode it covers up the panadapter display. The AGC-T control will lower the scope gain but it cuts the receiver gain too much. So what am I missing?? Thanks in advance for any help. Dennis, k0eoo _______________________________________________ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/ _______________________________________________ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/ _______________________________________________ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/