Jim Wilson wrote: > Should the Yasim 747 work now? Are there any files that need to be > checked into fgfsbase? I'm still getting the "Solution Failure" when > starting up the 747...and at some point I'd like to animate the 747 > model.
I don't think the most recent batch of updates has made it in yet. Attached is the current version I'm using. I can verify that it works for me. :) I've also attached my -set.xml file, which puts the cockpit in the correct place and doesn't reference a nonexistent panel. Andy -- Andrew J. Ross NextBus Information Systems Senior Software Engineer Emeryville, CA [EMAIL PROTECTED] http://www.nextbus.com "Men go crazy in conflagrations. They only get better one by one." - Sting (misquoted)
<airplane mass="400000"> <!-- Approach configuration --> <approach speed="136" aoa="7"> <control-setting axis="/controls/throttle[0]" value="0.2"/> <control-setting axis="/controls/throttle[1]" value="0.2"/> <control-setting axis="/controls/flaps" value="1.0"/> <control-setting axis="/controls/slats" value="1.0"/> <control-setting axis="/controls/gear-down" value="1"/> </approach> <!-- Cruise configuration --> <cruise speed="530" alt="41000"> <control-setting axis="/controls/throttle[0]" value="1.0"/> <control-setting axis="/controls/throttle[1]" value="1.0"/> <control-setting axis="/controls/flaps" value="0.0"/> <control-setting axis="/controls/gear-down" value="0"/> </cruise> <cockpit x="-5.42" y="1.81" z="15.06"/> <fuselage ax="0" ay="0" az="0" bx="-69.86" by="0.00" bz="2.41" width="6" taper="0.3" midpoint="0.2"/> <wing x="-26.50" y="3.01" z="-1.45" length="33.72" chord="13.25" sweep="33" taper=".27" dihedral="7" camber="0.1"> <stall aoa="15" width="2" peak="1.5"/> <flap0 start="0" end=".56" lift="1.8" drag="3"/> <flap1 start=".64" end=".88" lift="1.3" drag="1.5"/> <slat start="0" end="1" aoa="2" drag="1.1"/> <spoiler start="0.2" end="0.6" lift="0.3" drag="2.0"/> <control-input axis="/controls/flaps" control="FLAP0"/> <control-input axis="/controls/aileron" control="FLAP1" split="true"/> <control-input axis="/controls/aileron-trim" control="FLAP1" split="true"/> <control-input axis="/controls/slats" control="SLAT"/> <control-input axis="/controls/spoilers" control="SPOILER"/> <control-output control="FLAP0" prop="/surface-positions/flap-pos-norm"/> <control-output control="FLAP1" side="left" prop="/surface-positions/left-aileron-pos-norm"/> <control-output control="FLAP1" side="right" prop="/surface-positions/right-aileron-pos-norm"/> <control-speed control="FLAP0" transition-time="10"/> </wing> <hstab x="-62.63" y="1.81" z="1.81" chord="8.43" length="10.84" taper=".29" sweep="28" dihedral="7" effectiveness="2"> <stall aoa="15" width="2" peak="1.5"/> <flap0 start="0" end="1" lift="1.5" drag="2.0"/> <control-input axis="/controls/elevator" control="FLAP0"/> <control-input axis="/controls/elevator-trim" control="FLAP0"/> <control-output control="FLAP0" prop="/surface-positions/elevator-pos-norm"/> </hstab> <vstab x="-62.63" y="0.00" z="3.61" chord="12.04" length="12.04" taper="0.3" sweep="33"> <stall aoa="15" width="2" peak="1.5"/> <flap0 start="0" end="1" lift="1.2" drag="1.3"/> <control-input axis="/controls/rudder" control="FLAP0" invert="true"/> <control-input axis="/controls/rudder-trim" control="FLAP0" invert="true"/> <control-output control="FLAP0" prop="/surface-positions/rudder-pos-norm" min="1" max="-1"/> </vstab> <jet x="-34.93" y="16.26" z="-1.20" mass="8000" thrust="60000"> <control-input axis="/controls/throttle[0]" control="THROTTLE"/> </jet> <jet x="-26.50" y="12.65" z="-2.41" mass="8000" thrust="60000"> <control-input axis="/controls/throttle[0]" control="THROTTLE"/> </jet> <jet x="-26.50" y="-12.65" z="-2.41" mass="8000" thrust="60000"> <control-input axis="/controls/throttle[1]" control="THROTTLE"/> </jet> <jet x="-34.93" y="-16.26" z="-1.20" mass="8000" thrust="60000"> <control-input axis="/controls/throttle[1]" control="THROTTLE"/> </jet> <gear x="-5.42" y="0.00" z="-5.42" compression="2"> <!-- nose --> <control-input axis="/controls/rudder" control="STEER" square="true"/> <control-input axis="/controls/gear-down" control="EXTEND"/> <control-output control="EXTEND" prop="/gear/gear[0]/position-norm"/> <control-speed control="EXTEND" transition-time="7"/> </gear> <gear x="-29.15" y="5.42" z="-5.42" compression="2"> <!-- fwd left main --> <control-input axis="/controls/brakes[0]" control="BRAKE"/> <control-input axis="/controls/gear-down" control="EXTEND"/> <control-output control="EXTEND" prop="/gear/gear[1]/position-norm"/> <control-speed control="EXTEND" transition-time="7"/> </gear> <gear x="-31.32" y="1.81" z="-5.42" compression="2"> <!-- rear left main --> <control-input axis="/controls/brakes[0]" control="BRAKE"/> <control-input axis="/controls/gear-down" control="EXTEND"/> <control-output control="EXTEND" prop="/gear/gear[2]/position-norm"/> <control-speed control="EXTEND" transition-time="7"/> </gear> <gear x="-31.32" y="-1.81" z="-5.42" compression="2"> <!-- rear right main --> <control-input axis="/controls/brakes[1]" control="BRAKE"/> <control-input axis="/controls/gear-down" control="EXTEND"/> <control-output control="EXTEND" prop="/gear/gear[3]/position-norm"/> <control-speed control="EXTEND" transition-time="7"/> </gear> <gear x="-29.15" y="-5.42" z="-5.42" compression="2"> <!-- fwd right main --> <control-input axis="/controls/brakes[1]" control="BRAKE"/> <control-input axis="/controls/gear-down" control="EXTEND"/> <control-output control="EXTEND" prop="/gear/gear[4]/position-norm"/> <control-speed control="EXTEND" transition-time="7"/> </gear> <tank x="-26.50" y="0" z="-1.45" jet="true" capacity="128000"/> <tank x="-30.10" y="8" z="-1.45" jet="true" capacity="128000"/> <tank x="-30.10" y="-8" z="-1.45" jet="true" capacity="128000"/> <ballast x="-6" y="0" z="2.4" mass="30000"/> <!-- hump --> <ballast x="-12" y="0" z="2.4" mass="40000"/> <!-- hump --> <ballast x="-18" y="0" z="2.4" mass="40000"/> <!-- hump --> <ballast x="-24" y="0" z="2.4" mass="30000"/> <!-- hump --> </airplane>
<?xml version="1.0"?> <PropertyList> <sim> <flight-model>yasim</flight-model> <aero>747</aero> <fuel-fraction>0.5</fuel-fraction> <sound> <audible>true</audible> <path>Aircraft/747/747-sound.xml</path> </sound> <panel> <path>Aircraft/c310/c310-mini-panel.xml</path> <visibility>false</visibility> </panel> <hud> <path>Huds/Custom/default.xml</path> <visibility>true</visibility> </hud> <model> <path>Aircraft/747/Models/boeing747-400-jw.ac</path> </model> <view> <internal archive="y">true</internal> <config> <!-- x/y/z == right/up/back --> <x-offset-m archive="y">-1.81</x-offset-m> <y-offset-m archive="y">15.06</y-offset-m> <z-offset-m archive="y">5.42</z-offset-m> </config> </view> </sim> <autopilot> <config> <min-climb-speed-kt type="float">200.0</min-climb-speed-kt> <best-climb-speed-kt type="float">240.0</best-climb-speed-kt> <target-climb-rate-fpm type="float">2000.0</target-climb-rate-fpm> <target-descent-rate-fpm type="float">1000.0</target-descent-rate-fpm> <elevator-adj-factor type="float">12000.0</elevator-adj-factor> <integral-contribution type="float">0.005</integral-contribution> <zero-pitch-throttle type="float">0.65</zero-pitch-throttle> <zero-pitch-trim-full-throttle type="float">0.025</zero-pitch-trim-full-throttle> </config> </autopilot> </PropertyList>