Hi,
i've recently discovered this url:
http://sourceforge.net/mailarchive/message.php?msg_id=1389791
in which is explaned what the problem is with the CH product pro pedals. Now
I've compiled the pedals in joydev.c and hid-core.c and can see the
hid-core.c: hid_init_reports usb_set_idle()=-911
in dmesg, but still the joystick isn't recognised with js_demo. I've copied
the entire dmesg output, since I can't really tell what is relevant and what
isn't.
First lsmod, I need to load every module you see here. it doesn't work if i
don't
[EMAIL PROTECTED] operat]# lsmod
Module Size Used by
ehci-hcd 25732 0 (unused)
joydev 6060 0
hid 22404 0 (unused)
input 5312 0 (autoclean) [joydev hid]
nvidia 3859036 6
rtnet 53768 0
rtai_rtdm 12900 0 [rtnet]
rtai_shm 7368 0
rtai_fifos 17672 0
rtai_sched_up 48241 0 [rtnet rtai_rtdm]
rtai 39616 2 [rtnet rtai_rtdm rtai_shm rtai_fifos
rtai_sched_up]
3c59x 29552 1
usb-uhci 26668 0 (unused)
usbcore 83616 1 [ehci-hcd hid usb-uhci]
you can see it still doesn't work.....what am i doing wrong? I'm already
trying everything for 2 weeks....
greetings
Luuk van Hal
[EMAIL PROTECTED] operat]# js_demo
Joystick test program.
~~~~~~~~~~~~~~~~~~~~~~
Joystick 0: "CH PRODUCTS CH THROTTLE QUADRANT"
Joystick 1: "CH PRODUCTS CH FLIGHT SIM YOKE USB "
Joystick 2 not detected
Joystick 3 not detected
Joystick 4 not detected
Joystick 5 not detected
Joystick 6 not detected
Joystick 7 not detected
+--------------------JS.0----------------------+--------------------JS.1----------------------+
| Btns Ax:0 Ax:1 Ax:2 Ax:3 Ax:4 Ax:5 | Btns Ax:0 Ax:1 Ax:2 Ax:3
Ax:4 Ax:5 Ax:6 |
+----------------------------------------------+----------------------------------------------+
| 0000 -1.0 -1.0 -1.0 -1.0 -1.0 -1.0 . . | 0000 -0.1 -0.2 +1.0 +1.0
+1.0 +0.0 +0.0 . |
[EMAIL PROTECTED] operat]# dmesg
A PERIODIC TIMER *****
***<> LINUX TICK AT 100 (HZ) <>***
***<> CALIBRATED CPU FREQUENCY 3192095000 (HZ) <>***
***<> CALIBRATED TIMER-INTERRUPT-TO-SCHEDULER LATENCY 2688 (ns) <>***
***<> CALIBRATED ONE SHOT SETUP TIME 2010 (ns) <>***
RTDM Version 0.5.0
*** RTnet 0.7.0 - built on Jul 28 2004 15:05:34 ***
RTnet: initialising real-time networking
RTnet: stack-mgr started
RTDM: registered protocol device 2:2
RTDM: registered protocol device 17:2
8139too-rt Fast Ethernet driver 0.9.24-rt0.2
PCI: Found IRQ 11 for device 01:00.0
PCI: Sharing IRQ 11 with 00:1d.0
PCI: Sharing IRQ 11 with 00:1d.3
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-7174 Tue Mar 22
06:44:39 PST 2005
meminit hack
PCI: Found IRQ 5 for device 02:03.0
PCI: Sharing IRQ 5 with 00:1d.1
spurious 8259A interrupt: IRQ7.
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[EMAIL PROTECTED]>
hid-core.c: USB HID support drivers
PCI: Found IRQ 9 for device 00:1d.7
PCI: Setting latency timer of device 00:1d.7 to 64
ehci_hcd 00:1d.7: Intel Corp. 82801EB USB2
ehci_hcd 00:1d.7: irq 9, pci mem e1e15000
usb.c: new USB bus registered, assigned bus number 5
ehci_hcd 00:1d.7: ehci_start hcs_params 0x104208 dbg=1 cc=4 pcc=2 ordered
!ppc ports=8
ehci_hcd 00:1d.7: ehci_start hcc_params 6871 thresh 7 uframes 1024 64 bit
addr
ehci_hcd 00:1d.7: capability 10001 at 68
ehci_hcd 00:1d.7: BIOS handoff succeeded
ehci_hcd 00:1d.7: reset command 080012 (park)=0 ithresh=8 Periodic
period=1024 Reset HALT
ehci_hcd 00:1d.7: enabled 64bit PCI DMA
PCI: cache line size of 128 is not supported by device 00:1d.7
ehci_hcd 00:1d.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
ehci_hcd 00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-19/2.4
hcd.c: 00:1d.7 root hub device address 1
hub.c: port 1, portstatus 100, change 1, 12 Mb/s
hub.c: port 1 connection change
hub.c: port 1, portstatus 100, change 1, 12 Mb/s
hub.c: port 2, portstatus 100, change 0, 12 Mb/s
usb.c: kmalloc IF cfd9af00, numif 1
usb.c: new device strings: Mfr=3, Product=2, SerialNumber=1
usb.c: USB device number 1 default language ID 0x0
Manufacturer: Linux 2.4.24-rthal5 ehci_hcd
Product: Intel Corp. 82801EB USB2
SerialNumber: 00:1d.7
hub.c: USB hub found
hub.c: 8 ports detected
hub.c: standalone hub
hub.c: ganged power switching
hub.c: individual port over-current protection
hub.c: Single TT
hub.c: TT requires at most 8 FS bit times
hub.c: Port indicators are not supported
hub.c: power on to power good time: 0ms
hub.c: hub controller current requirement: 0mA
hub.c: port removable status: RRRRRRRR
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
usb.c: hub driver claimed interface cfd9af00
usb.c: kusbd: /sbin/hotplug add 1
ehci_hcd 00:1d.7: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT
hub.c: port 1, portstatus 501, change 1, 480 Mb/s
hub.c: port 1 connection change
hub.c: port 1, portstatus 501, change 1, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 511, change 0, 480 Mb/s
hub.c: port 1 of hub 1 not reset yet, waiting 10ms
hub.c: port 1, portstatus 511, change 0, 480 Mb/s
hub.c: port 1 of hub 1 not reset yet, waiting 10ms
ehci_hcd 00:1d.7: port 1 high speed
ehci_hcd 00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
hub.c: port 1, portstatus 503, change 10, 480 Mb/s
hub.c: new USB device 00:1d.7-1, assigned address 2
usb.c: kmalloc IF cfd9adc0, numif 1
usb.c: new device strings: Mfr=0, Product=0, SerialNumber=0
hub.c: USB hub found
hub.c: 4 ports detected
hub.c: standalone hub
hub.c: individual port power switching
hub.c: individual port over-current protection
hub.c: TT per port
hub.c: TT requires at most 8 FS bit times
hub.c: Port indicators are supported
hub.c: power on to power good time: 100ms
hub.c: hub controller current requirement: 100mA
hub.c: port removable status: RRRR
hub.c: local power source is good
hub.c: no over-current condition exists
ehci-sched.c: scheduled qh c85b5100 usecs 7/0 period 256.0 starting 255.0
(gap 0)
hub.c: enabling power on all ports
usb.c: hub driver claimed interface cfd9adc0
usb.c: kusbd: /sbin/hotplug add 2
hub.c: port 2, portstatus 100, change 0, 12 Mb/s
hub.c: port 3, portstatus 100, change 0, 12 Mb/s
hub.c: port 4, portstatus 100, change 0, 12 Mb/s
hub.c: port 5, portstatus 100, change 0, 12 Mb/s
hub.c: port 6, portstatus 100, change 0, 12 Mb/s
hub.c: port 7, portstatus 100, change 0, 12 Mb/s
hub.c: port 8, portstatus 100, change 0, 12 Mb/s
hub.c: port 1, portstatus 100, change 0, 12 Mb/s
hub.c: port 2, portstatus 301, change 1, 1.5 Mb/s
hub.c: port 2 connection change
hub.c: port 2, portstatus 301, change 1, 1.5 Mb/s
hub.c: port 2, portstatus 301, change 0, 1.5 Mb/s
hub.c: port 2, portstatus 301, change 0, 1.5 Mb/s
hub.c: port 2, portstatus 301, change 0, 1.5 Mb/s
hub.c: port 2, portstatus 301, change 0, 1.5 Mb/s
hub.c: port 2, portstatus 303, change 10, 1.5 Mb/s
hub.c: new USB device 00:1d.7-1.2, assigned address 3
usb.c: kmalloc IF c1927340, numif 1
usb.c: skipped 1 class/vendor specific interface descriptors
usb.c: new device strings: Mfr=1, Product=2, SerialNumber=0
usb.c: USB device number 3 default language ID 0x409
Manufacturer: CH PRODUCTS
Product: CH THROTTLE QUADRANT
ehci-q.c: clear tt 00:1d.7-1 p2 buffer, a3 ep0
hid-core.c: hid_init_reports usb_set_idle()=-32
input: USB HID v1.00 Joystick [CH PRODUCTS CH THROTTLE QUADRANT] on usb5:3.0
usb.c: hid driver claimed interface c1927340
usb.c: kusbd: /sbin/hotplug add 3
hub.c: port 3, portstatus 301, change 1, 1.5 Mb/s
hub.c: port 3 connection change
hub.c: port 3, portstatus 301, change 1, 1.5 Mb/s
hub.c: port 3, portstatus 301, change 0, 1.5 Mb/s
hub.c: port 3, portstatus 301, change 0, 1.5 Mb/s
hub.c: port 3, portstatus 301, change 0, 1.5 Mb/s
hub.c: port 3, portstatus 301, change 0, 1.5 Mb/s
hub.c: port 3, portstatus 303, change 10, 1.5 Mb/s
hub.c: new USB device 00:1d.7-1.3, assigned address 4
usb.c: kmalloc IF c1927300, numif 1
usb.c: skipped 1 class/vendor specific interface descriptors
usb.c: new device strings: Mfr=1, Product=2, SerialNumber=0
usb.c: USB device number 4 default language ID 0x409
Manufacturer: CH PRODUCTS
Product: CH PRO PEDALS USB
hid-core.c: hid_init_reports usb_set_idle()=-911
input: USB HID v1.00 Joystick [CH PRODUCTS CH PRO PEDALS USB ] on usb5:4.0
usb.c: hid driver claimed interface c1927300
usb.c: kusbd: /sbin/hotplug add 4
hub.c: port 4, portstatus 301, change 1, 1.5 Mb/s
hub.c: port 4 connection change
hub.c: port 4, portstatus 301, change 1, 1.5 Mb/s
hub.c: port 4, portstatus 301, change 0, 1.5 Mb/s
hub.c: port 4, portstatus 301, change 0, 1.5 Mb/s
ehci-sched.c: scheduled qh c85b5280 usecs 8/15 period 8.0 starting 6.0 (gap
1)
hub.c: port 4, portstatus 301, change 0, 1.5 Mb/s
hub.c: port 4, portstatus 301, change 0, 1.5 Mb/s
hub.c: port 4, portstatus 303, change 10, 1.5 Mb/s
hub.c: new USB device 00:1d.7-1.4, assigned address 5
usb.c: kmalloc IF c1927640, numif 1
usb.c: skipped 1 class/vendor specific interface descriptors
usb.c: new device strings: Mfr=1, Product=2, SerialNumber=0
usb.c: USB device number 5 default language ID 0x409
Manufacturer: CH PRODUCTS
Product: CH FLIGHT SIM YOKE USB
hid-core.c: hid_init_reports usb_set_idle()=-911
input: USB HID v1.00 Joystick [CH PRODUCTS CH FLIGHT SIM YOKE USB ] on
usb5:5.0
usb.c: hid driver claimed interface c1927640
usb.c: kusbd: /sbin/hotplug add 5
hub.c: port 1, portstatus 100, change 0, 12 Mb/s
hub.c: port 2, portstatus 303, change 0, 1.5 Mb/s
hub.c: port 3, portstatus 303, change 0, 1.5 Mb/s
hub.c: port 4, portstatus 303, change 0, 1.5 Mb/s
ehci-sched.c: descheduled qh c85b5280, period = 8 frame = 1030 count = 2,
urbs = 1
ehci-sched.c: reused previous qh c85b5280 schedule
ehci-sched.c: scheduled qh c85b5280 usecs 8/15 period 8.0 starting 6.0 (gap
1)
ehci-sched.c: scheduled qh c85b5380 usecs 8/15 period 8.0 starting 5.0 (gap
1)
ehci-sched.c: descheduled qh c85b5280, period = 8 frame = 1030 count = 2,
urbs = 2
ehci-sched.c: descheduled qh c85b5380, period = 8 frame = 1029 count = 2,
urbs = 1
ehci-sched.c: reused previous qh c85b5280 schedule
ehci-sched.c: scheduled qh c85b5280 usecs 8/15 period 8.0 starting 6.0 (gap
1)
ehci-sched.c: reused previous qh c85b5380 schedule
ehci-sched.c: scheduled qh c85b5380 usecs 8/15 period 8.0 starting 5.0 (gap
1)
ehci-sched.c: descheduled qh c85b5280, period = 8 frame = 1030 count = 2,
urbs = 2
ehci-sched.c: descheduled qh c85b5380, period = 8 frame = 1029 count = 2,
urbs = 1
_______________________________________________
Flightgear-devel mailing list
Flightgear-devel@flightgear.org
http://mail.flightgear.org/mailman/listinfo/flightgear-devel
2f585eeea02e2c79d7b1d8c4963bae2d
