We didn't physically remove the module yet (it's 150KM away) so i hoped there was a different way of doing it.
The boot procedure on the LP is pretty non-explanatory : tel...@r#lp boot system mp pri 2 tel...@r#rconsole 2 Remote connection to LP slot 2 established Press CTRL-X or type 'exit' to disconnect it NetIron XMR/MLX Boot Monitor Version 3.5.00e Enter 'b' to stop at boot monitor sent IPC_MSGTYPE_REBOOT to slot 16 (my_slot = 1, ipc_post_rx32_mode = 0) received IPC_MSGTYPE_REBOOT_ACK from fid d020 REV B LP get_module_type: board_class = cf 207 20 ipc_send_card_boot: module_type = 20 REV B LP get_module_type: board_class = cf 207 20 PPCR type = 2, xtm_arg = 1, xpp_arg = 0, pbif_arg = 0, xgmac_arg = 0, hv_cam_type = ff, hv_value = 0 sent IPC_MSGTYPE_LP_CARD_BOOT to slot 32 Received IPC_MSGTYPE_MP_CARD_BOOT_INFO g_bp_board_class_val = 0x86, g_rx16_backplane_type = 255 BOOT INFO: boot interactively REV B LP get_module_type: board_class = cf 207 20 REV B LP get_module_type: board_class = cf 207 20 PPCR type = 2, xtm_arg = 1, xpp_arg = 0, pbif_arg = 0, xbridge_arg = 0, xgmac_arg = 0, hv_cam_type = ff, hv_value = 0 sent IPC_MSGTYPE_LP_CARD_SW_LOADED (failed) to slot 32 So i think we have to physically eject the module :( Regards, Remco On 11/09/2010 05:41 PM, Jared Valentine wrote: > Sounds like you need to: > > 1.) physically remove module > 2.) remove slot configuration using "no module xxx" > 3.) pre-stage the config with the new module "module xxx" > 3.) physically replace module > 4.) deal with the software issue > > -Jared > > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of Remco Bressers > Sent: Tuesday, November 09, 2010 9:16 AM > To: [email protected] > Subject: Re: [f-nsp] Not able to use XMR 10 gig linecard > > Unfortunately that won't work because of the same reason : > > tel...@ams-er8-sara(config)#no module 2 ni-xmr-20-port-1g > Error: Please remove module from slot 2 first > > Also, powering off the card won't do. > > :( > > Regards, > > Remco > > > On 11/09/2010 05:12 PM, Michiel Muhlenbaumer wrote: >> First run 'no module blabla' and then power-off/on the lc. >> >> Met vriendelijke groet, >> Best regards, >> >> Michiel Muhlenbaumer >> Atrato IP Networks >> >> (sent from mobile device) >> >> On 9 nov. 2010, at 16:58, Remco Bressers <[email protected]> wrote: >> >>> Hi, >>> >>> The other day, i inserted a brand new NI-XMR-10Gx4 in an XMR-4, but it >>> won't work correctly. >>> If i do a "show module", i see the following output on the slot : >>> >>> S2: NI-XMR-10Gx4 4-port 10GbE Module CARD_STATE_INTERACTIVE 20 >>> 0012.f2f5.d128 >>> (S2: Configured as NI-XMR-1Gx20-SFP 20-port 1GbE/100FX Module) >>> >>> What is the correct procedure to configure S2 as ni-xmr-10gx4 ? >>> >>> I tried : >>> >>> tel...@r(config)#module 2 ni-xmr-4-port-10g >>> Error: Please remove module from slot 2 first >>> tel...@r(config)# >>> >>> Is this the only (and correct) way? >>> >>> -- >>> Kind regards, >>> Signet bv >>> >>> Remco Bressers >>> _______________________________________________ >>> foundry-nsp mailing list >>> [email protected] >>> http://puck.nether.net/mailman/listinfo/foundry-nsp > > -- Met vriendelijke groet, Signet bv Remco Bressers T 040 - 707 4 907 F 040 - 707 4 909 E [email protected] altijd online? www.signet.nl _______________________________________________ foundry-nsp mailing list [email protected] http://puck.nether.net/mailman/listinfo/foundry-nsp
