On 30 Sep 13, at 17:47, LubomĂr ÄŚabla wrote: > Attempt to compile IDE: > > OS Windows XP 32 CZ > FPC GO32V2 2.6.2 is installed in z:\pp > PATH contains Z:\pp\bin\go32v2 > > 1. 29.09.2013 download source package > ftp://ftp.freepascal.org/pub/fpc/snapshot/fixes/source/fpc.zip > > 2. unpacked to z:\fpc > > 3. command for compilation: > > Z:\fpc>make rtl_all packages_all ide_all "OPT=-gl -O-" "NOGDB=1" > > x130930.log . . > fprepos.pp(22,3) Fatal: Can't find unit fpmkunit used by fprepos > > even the unit fpmkunit has been compiled (at least I think so) into > Z:\fpc\packages\fpmkunit\units\go32v2 where are these files: . .
Yes, sorry - a dependency has been missing in our makefile (triggered only for some targets; unfortunately, GO32v2 being one of them). The issue is fixed in svn, but I'm not sure if it will still get in tonight's source zip file generation. Tomas > > On Thu, Sep 19, 2013 at 11:07 AM, Tomas Hajny <xhaj...@hajny.biz> wrote: > > > On Wed, September 18, 2013 20:49, LubomĂr ÄŚabla wrote: > > > I am running pure DOS 7 from Windows 98 US, no drivers, no TSR programs. > > > Just COMMAND.COM, no AUTOEXEC.BAT and CONFIG.SYS. > > > > > > Run > > > > > > CWSDPMI -p -x > > > > > > DPMI stays in memory, start FP.EXE - again SIGSEGV. > > . > > . > > > > OK, thanks. > > > > > > > Can you tell me where can I download source for IDE from FPC 2.6.2 > > > and how to compile it? > > > > > > I will try it when I have a free weekend. > > > > See links on http://www.freepascal.org/develop.var - you can e.g. try > > downloading fpc.zip source package for fixes from FTP. Unpack it somewhere > > and run: > > > > make rtl_all packages_all ide_all "OPT=-gl -O-" "NOGDB=1" > > > > That should compile IDE without the debugging support, but that should be > > sufficient for start. If the problem cannot be replicated that way, the > > next step would be downloading the pre-compiled libgdb > > (ftp://ftp.freepascal.org/pub/fpc/contrib/libgdb/v6.1.1/go32v2-v601.zip), > > creating directory "libgdb" next to "rtl", "ide" and "packages", unpacking > > content of the downloaded file there and then compiling again using: > > > > make clean rtl_all packages_all ide_all "OPT=-gl -O-" > > > > If that still works, you could remove the "-O-" bit to see if the > > optimizations make any difference. > > > > Tomas > > > > > > > > > > > > On Wed, Sep 18, 2013 at 8:52 AM, Tomas Hajny <xhaj...@hajny.biz> wrote: > > > > > >> On Tue, September 17, 2013 20:57, LubomĂr ÄŚabla wrote: > > >> > FPC 2.6.2 for DOS/Go32V2 > > >> > > > >> > There is the fatal IDE unstability in FPC 2.6.2 under pure DOS. > > >> > > > >> > IDE almost always starts only first time (after installation or > > >> reboot). > > >> > I start the IDE, compile and run the program (e.g. Hello.pas) and > > >> close > > >> > IDE. But when I want to start IDE again it crashes with SIGSEGV > > >> message. > > >> > > > >> > Exiting due to signal SIGSEGV > > >> > FPC General Protection Fault at eip=006EDE95 > > >> > eax=65672D6C ebx=0000002A ecx=00000088 edx=00000000 esi=008E91F8 > > >> > edi=0083B504 > > >> > ebp=008C0CA0 esp=008C0C90 program=C:\PP\BIN\GO32V2\FP.EXE > > >> > cs: sel=00A7 base=00400000 limit=008EFFFF > > >> > ds: sel=00AF base=00400000 limit=008EFFFF > > >> > es: sel=00AF base=00400000 limit=008EFFFF > > >> > fs: sel=00C7 base=00000000 limit=0010FFFF > > >> > gs: sel=00C7 base=00000000 limit=0010FFFF > > >> > ss: sel=00AF base=00400000 limit=008EFFFF > > >> > > > >> > Call frame traceback EIPs: > > >> > $006EDE95 > > >> > $005BD905 > > >> > $005BCD84 > > >> > $005BC83D > > >> > $005BC7F8 > > >> > $00308AF8 > > >> > $0030B9F4 > > >> > $0002DB50 > > >> > $0002DC5A > > >> > $00002040 > > >> > > > >> > To be able to start IDE again in DOS I have to reboot the computer. > > >> > I think IDE set something in memory and warm restart does not erase > > >> the > > >> > memory contents. > > >> > > > >> > Compilation from command prompt with FPC.EXE works everywhere. > > >> > But IDE is good for debugging and help. > > >> > > > >> > Can someone please help me or advise what I'm doing wrong. > > >> > > > >> > The main problem is running IDE in pure DOS. > > >> > > >> Which DOS version is it? Is there any DPMI provider running before > > >> starting the IDE (some DOS versions include DPMI host themselves)? > > >> > > >> If there is no other DPMI host (running) and thus CWSDPMI.EXE is used, > > >> I'd > > >> recommend starting with a check whether there is just one (the latest) > > >> CWSDPMI.EXE and just for test purposes try loading it into memory as TSR > > >> with options "-p -x" (see cwsdpmi.txt included in directory doc\fpc) to > > >> see if it makes any difference. > > >> > > >> Obviously, the next step would be compiling the IDE with debug > > >> information > > >> (including -gl) to see where exactly it fails. > > >> > > >> Tomas _______________________________________________ fpc-pascal maillist - fpc-pascal@lists.freepascal.org http://lists.freepascal.org/mailman/listinfo/fpc-pascal