If you’re in LA try Andree Martin: https://www.amcamera.com/about/
You might also see if Whitehouse AV will tackle it. Which crystal motor do you have? There were many for the NPR — KRYMO, BEALA, Perfectone, Aaton, and several conversions of DC motors like Hafflex. Some will be easier to repair than others, but the boards are probably pretty easy to work on compared to modern electronics. Jeff Kreines Kinetta j...@kinetta.com kinetta.com Sent from iPhone. > On Feb 19, 2020, at 1:10 PM, 16mm Directory <i...@16mmdirectory.org> wrote: > > > > >> On Wed, Feb 19, 2020 at 7:57 AM mariah garnett <mariah.garn...@gmail.com> >> wrote: >> Thanks Scott, >> It has a crystal sync motor. Does this mean I could just take it to an >> analog camera store or repair shop in LA? That’s where I’m based and would >> rather not have to ship it anywhere... > > > > Mariah, > > I definitely agree with Scott, the motor can be easily detached and serviced, > though a full CLA or overhaul is likely in order. I service > my camera on regular intervals, and never let it sit for too long without > running the motor, just to keep the mechanism lubricated. > > If you're in LA, I suggest trying Richard Bennett at Cinema Engineering > (http://www.cinemaengineering.com/). He can do some Eclair NPR > service, and likely has a source for parts. Also, when George retired and > Optical-Electro House shut down, Bob Allen, who used to work > at OEH with George (and has years of experience with Eclair) was continuing > to do service. It's been a few years since I had this conversation > with George, but here is the last contact I have for Bob Allen...323-732-0607 > or 310-918-9017. > > Last I checked with Alan Gordon and Birns & Sawyer, they no longer had folks > around who could perform this work. Otherwise, you have > options in the midwest. Mansung (SMS Chicago) was still doing some work in > retirement, and Visual Products does service and has a cache > of NPR parts. Paul Scaglione is/was the main VP tech with Eclair knowledge. > > Lastly, for motor service, try Andrew at AZ spectrum (NY). He serviced my NPR > Alcan motor a few years back, still works great. That says a > lot since nobody liked working on the Alcan motors, not even George at OEH. > > Like Scott mentioned, if it's another NPR motor > (http://www.tfgtransfer.com/motors.htm), besides the Alcan, these are easy > for most techs to > work on. > > Alain > > > > > > > >> >> > On Feb 19, 2020, at 6:59 AM, Scott Dorsey <klu...@panix.com> wrote: >> > >> > Which motor does it have? I am presuming the motor is the issue? There >> > are probably more different motors available for the NPR than any other >> > camera made. If it's one of the crystal sync motors, the electronics on >> > them aren't hard to work on and most of what goes bad are electrolytic >> > capacitors. If it's a wild DC motor, before doing anything open up the >> > brush compartments and make sure the brushes are in good condition. Always >> > keep spare brushes on hand. >> > --scott >> > _______________________________________________ >> > FrameWorks mailing list >> > FrameWorks@jonasmekasfilms.com >> > https://mailman-mail5.webfaction.com/listinfo/frameworks >> _______________________________________________ >> FrameWorks mailing list >> FrameWorks@jonasmekasfilms.com >> https://mailman-mail5.webfaction.com/listinfo/frameworks > > > -- > > 16mm Directory / 40 Frames > Portland, Oregon USA > > www.16mmdirectory.org > www.40frames.org > > _______________________________________________ > FrameWorks mailing list > FrameWorks@jonasmekasfilms.com > https://mailman-mail5.webfaction.com/listinfo/frameworks
_______________________________________________ FrameWorks mailing list FrameWorks@jonasmekasfilms.com https://mailman-mail5.webfaction.com/listinfo/frameworks
