Well, I got rid of the old Voxware drivers and went with the pnp drivers
and still nothing. Here is the dmesg:
--
Copyright (c) 1992-1999 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 4.0-CURRENT #11: Fri Sep 3 11:06:20 EDT 1999
[EMAIL PROTECTED]:/usr/src/sys/compile/ARTHUR
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium/P55C (167.05-MHz 586-class CPU)
Origin = "GenuineIntel" Id = 0x543 Stepping = 3
Features=0x8001bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,MMX>
real memory = 67108864 (65536K bytes)
avail memory = 62185472 (60728K bytes)
Preloaded elf kernel "kernel" at 0xc02cd000.
Intel Pentium detected, installing workaround for F00F bug
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
isab0: <Intel 82371SB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
ide_pci0: <Intel PIIX3 Bus-master IDE controller> at device 7.1 on pci0
vga-pci0: <Matrox MGA 1024SG/1064SG/1164SG graphics accelerator> irq 10 at device 10.0
on pci0
xl0: <3Com 3c905B-TX Fast Etherlink XL> irq 11 at device 11.0 on pci0
xl0: Ethernet address: 00:10:4b:c5:24:df
miibus0: <MII bus> on xl0
xlphy0: <3Com internal media interface> on miibus0
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
wdc0 at port 0x1f0-0x1f7 irq 14 on isa0
wdc0: unit 0 (wd0): <WDC AC23200L>
wd0: 3098MB (6346368 sectors), 6296 cyls, 16 heads, 63 S/T, 512 B/S
wdc1 at port 0x170-0x177 irq 15 on isa0
wdc1: unit 0 (atapi): <E285XA/1.00>, removable, dma, iordis
wcd0: drive speed 1377KB/sec, 240KB cache
wcd0: supported read types: CD-DA
wcd0: Audio: play, 255 volume levels
wcd0: Mechanism: ejectable tray
wcd0: Medium: no/blank disc inside, unlocked
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
vga0: <Generic ISA VGA> at port 0x3b0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0 at port 0x378-0x37f irq 7 flags 0x40 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
ppi0: <generic parallel i/o> on ppbus 0
pcm0: <SoundBlaster 16 4.13> at port 0x220-0x22f irq 5 drq 5 flags 0x15 on isa0
unknown0: <Game> on isa0
unknown1: <Audio> at port 0x240-0x24f,0x300-0x301,0x388-0x38b irq 9 drq 1,7 on isa0
changing root device to wd0s1a
WARNING: / was not properly dismounted
---
and here is the kernel config file:
---
#
# ARTHUR -- Customized kernel for arthur (starwars.linuxberg.org)
#
# $Id: ARTHUR,v 1.182 1999/08/15 09:54:56 phk Exp $
machine i386
cpu I586_CPU
ident ARTHUR
maxusers 32
#makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
options MATH_EMULATE #Support for x87 emulation
options INET #InterNETworking
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep this!]
options MFS #Memory Filesystem
options MFS_ROOT #MFS usable as root device, "MFS" req'ed
options NFS #Network Filesystem
options NFS_ROOT #NFS usable as root device, "NFS" req'ed
options MSDOSFS #MSDOS Filesystem
options CD9660 #ISO 9660 Filesystem
options CD9660_ROOT #CD-ROM usable as root. "CD9660" req'ed
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!]
options SCSI_DELAY=15000 #Be pessimistic about Joe SCSI device
options UCONSOLE #Allow users to grab the console
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
options KTRACE #ktrace(1) syscall trace support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
# To make an SMP kernel, the next two are needed
#options SMP # Symmetric MultiProcessor Kernel
#options APIC_IO # Symmetric (APIC) I/O
# Optionally these may need tweaked, (defaults shown):
#options NCPU=2 # number of CPUs
#options NBUS=4 # number of busses
#options NAPIC=1 # number of IO APICs
#options NINTR=24 # number of INTs
controller isa0
controller pnp0 # PnP support for ISA
controller eisa0
controller pci0
# Floppy drives
controller fdc0 at isa? port IO_FD1 irq 6 drq 2
disk fd0 at fdc0 drive 0
disk fd1 at fdc0 drive 1
# IDE controller and disks
controller wdc0 at isa? port IO_WD1 irq 14
disk wd0 at wdc0 drive 0
disk wd1 at wdc0 drive 1
controller wdc1 at isa? port IO_WD2 irq 15
disk wd2 at wdc1 drive 0
disk wd3 at wdc1 drive 1
# ATAPI devices on wdc?
device wcd0 #IDE CD-ROM
device wfd0 #IDE Floppy (e.g. LS-120)
device wst0 #IDE Tape (e.g. Travan)
# SCSI Controllers
# A single entry for any of these controllers (ncr, ahb, ahc) is
# sufficient for any number of installed devices.
#controller ncr0 # NCR/Symbios Logic
#controller ahb0 # EISA AHA1742 family
#controller ahc0 # AHA2940 and onboard AIC7xxx devices
#controller isp0 # Qlogic family
#controller dpt0 # DPT Smartcache - See LINT for options!
#controller adv0 at isa? port ? irq ?
#controller adw0
#controller bt0 at isa? port ? irq ?
#controller aha0 at isa? port ? irq ?
# SCSI peripherals
# Only one of each of these is needed, they are dynamically allocated.
#controller scbus0 # SCSI bus (required)
#device da0 # Direct Access (disks)
#device sa0 # Sequential Access (tape etc)
#device cd0 # CD
#device pass0 # Passthrough device (direct SCSI access)
# Proprietary or custom CD-ROM Interfaces
#device wt0 at isa? port 0x300 irq 5 drq 1
#device mcd0 at isa? port 0x300 irq 10
#device matcd0 at isa? port 0x230
#device scd0 at isa? port 0x230
# atkbdc0 controls both the keyboard and the PS/2 mouse
controller atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1
device psm0 at atkbdc? irq 12
device vga0 at isa? port ? conflicts
# splash screen/screen saver
pseudo-device splash
# syscons is the default console driver, resembling an SCO console
device sc0 at isa?
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device vt0 at isa?
#options XSERVER # support for X server
#options FAT_CURSOR # start with block cursor
# If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines
#options PCVT_SCANSET=2 # IBM keyboards are non-std
# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13
# Power management support (see LINT for more options)
device apm0 at nexus? disable flags 0x31 # Advanced Power Management
# PCCARD (PCMCIA) support
#controller card0
#device pcic0 at card?
#device pcic1 at card?
# Serial (COM) ports
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
#device sio2 at isa? disable port IO_COM3 irq 5
#device sio3 at isa? disable port IO_COM4 irq 9
# Parallel port
device ppc0 at isa? port? flags 0x40 irq 7
controller ppbus0 # Parallel port bus (required)
#device lpt0 # Printer
#device plip0 # TCP/IP over parallel
device ppi0 # Parallel port interface device
#controller vpo0 # Requires scbus and da0
controller miibus0
# PCI Ethernet NICs.
#device al0 # ADMtek AL981 (``Comet'')
#device ax0 # ASIX AX88140A
#device de0 # DEC/Intel DC21x4x (``Tulip'')
#device fxp0 # Intel EtherExpress PRO/100B (82557,82558)
#device mx0 # Macronix 98713/98715/98725 (``PMAC'')
#device pn0 # Lite-On 82c168/82c169 (``PNIC'')
#device rl0 # RealTek 8129/8139
#device sf0 # Adaptec AIC-6915 (``Starfire'')
#device tl0 # Texas Instruments ThunderLAN
#device tx0 # SMC 9432TX (83c170 ``EPIC'')
#device vr0 # VIA Rhine, Rhine II
#device vx0 # 3Com 3c590, 3c595 (``Vortex'')
#device wb0 # Winbond W89C840F
device xl0 # 3Com 3c90x (``Boomerang'', ``Cyclone'')
# ISA Ethernet NICs.
# The probe order of these is presently determined by i386/isa/isa_compat.c.
#device ed0 at isa? port 0x280 irq 10 iomem 0xd8000
#device ie0 at isa? port 0x300 irq 10 iomem 0xd0000
#device ep0 at isa? port 0x300 irq 10
#device ex0 at isa? port? irq?
#device fe0 at isa? port 0x300 irq ?
#device le0 at isa? port 0x300 irq 5 iomem 0xd0000
#device lnc0 at isa? port 0x280 irq 10 drq 0
#device cs0 at isa? port 0x300 irq ?
# requires PCCARD (PCMCIA) support to be activated
#device xe0 at isa? port? irq ?
# PCCARD NIC drivers.
# ze and zp take over the pcic and cannot coexist with generic pccard
# support, nor the ed and ep drivers they replace.
#device ze0 at isa? port 0x300 irq 10 iomem 0xd8000
#device zp0 at isa? port 0x300 irq 10 iomem 0xd8000
# Pseudo devices - the number indicates how many units to allocated.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
pseudo-device sl 1 # Kernel SLIP
pseudo-device ppp 1 # Kernel PPP
pseudo-device tun # Packet tunnel, for ppp(1)
pseudo-device pty # Pseudo-ttys (telnet etc)
pseudo-device gzip # Exec gzipped a.out's
# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
pseudo-device bpf #Berkeley packet filter
# USB support
#controller uhci0 # UHCI PCI->USB interface
#controller ohci0 # OHCI PCI->USB interface
#controller usb0 # USB Bus (required)
#device ugen0 # Generic
#device uhid0 # "Human Interface Devices"
#device ukbd0 # Keyboard
#device ulpt0 # Printer
#controller umass0 # Disks/Mass storage - Requires scbus and da0
#device ums0 # Mouse
# Sound driver
device pcm0
---
I am stumped.
Arthur H. Johnson II
http://www.linuxberg.com
Linuxberg Manager
[EMAIL PROTECTED]
To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-current" in the body of the message
