Hi Folks, We've been trying to bring freebsd up on a hp dl980g7 for awhile. Due to usb issues, we finally installed onto a revo card and installed it into the 980. The system consistently puts out the following messages:
usbd_ctrl_transfer_setup: could not setup default USB transfer usb_alloc_device: set address 2 failed (USB_ERR_NOMEM, ignored) usbd_ctrl_transfer_setup: could not setup default USB transfer usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_NOMEM usbd_ctrl_transfer_setup: could not setup default USB transfer usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_NOMEM, ignored) usbd_ctrl_transfer_setup: could not setup default USB transfer usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_NOMEM usbd_ctrl_transfer_setup: could not setup default USB transfer usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_NOMEM, ignored) usbd_ctrl_transfer_setup: could not setup default USB transfer usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_NOMEM ugen0.2: <Unknown> at usbus0 (disconnected) uhub_reattach_port: could not allocate new device From dmesg: pci0: <base peripheral, interrupt controller> at device 20.0 (no driver attached) pcib12: <ACPI PCI-PCI bridge> at device 28.0 on pci0 pci3: <ACPI PCI bus> on pcib12 pcib13: <ACPI PCI-PCI bridge> at device 28.4 on pci0 pci2: <ACPI PCI bus> on pcib13 pci2: <base peripheral> at device 0.0 (no driver attached) pci2: <base peripheral> at device 0.2 (no driver attached) uhci0: <UHCI (generic) USB controller> port 0x3c00-0x3c1f irq 17 at device 0.4 on pci2 usbus0 on uhci0 uhci1: <Intel 82801JI (ICH10) USB controller USB-A> port 0x1000-0x101f irq 20 at device 29.0 on pci0 device_attach: uhci1 attach returned 12 uhci1: <Intel 82801JI (ICH10) USB controller USB-B> port 0x1020-0x103f irq 23 at device 29.1 on pci0 device_attach: uhci1 attach returned 12 uhci1: <Intel 82801JI (ICH10) USB controller USB-C> port 0x1040-0x105f irq 22 at device 29.2 on pci0 device_attach: uhci1 attach returned 12 uhci1: <Intel 82801JI (ICH10) USB controller USB-F> port 0x1060-0x107f irq 23 at device 29.3 on pci0 device_attach: uhci1 attach returned 12 ehci0: <Intel 82801JI (ICH10) USB 2.0 controller USB-A> mem 0xa0300000-0xa03003ff irq 20 at device 29.7 on pci0 device_attach: ehci0 attach returned 12 Current - 10.0-CURRENT FreeBSD 10.0-CURRENT #0 r235137M Nothing connected to usb on this systems works. Full dmesg is here: http://people.freebsd.org/~jwd/dl980g7/dmesg.boot.html Any help is appreciated. Thanks, John _______________________________________________ freebsd-current@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "freebsd-current-unsubscr...@freebsd.org"
