The jumpers aren't set right. If they aren't set right FreeBSD will
recognize the card at boot, but it won't be able to probe it at all.
At 01:59 PM 7/8/00 -0500, Robert Small wrote:
>Damon Hammis wrote:
>
> > The jumpers are set wrong on the card. I had the exact same problem with
> > an aha-1542 and aha-1540 card recently. The docs on the jumpers that you
> > can get on Adaptec's site are kind of cryptic, but the card will work once
> > you get the jumpers placed correctly.
> >
> > Currently I have mine running at irq 9, drq 5 and my jumpers are setup
> > like this:
> >
> > J5 pin 8 jumpered pin 9 the jumper is on one pin
> > J9 pins 2, 6, and 9 are jumpered.
> >
> > I have that configuration running on two systems now working great. Let
> > me know how it goes for ya.
> >
> > --Damon
> >
> > On Fri, 7 Jul 2000, Robert Small wrote:
> >
> > > I installed an Adaptec AHA-1542 controller in my system tonight, and
> > > hooked up a Sony SDT-5000 tape drive.
> > >
> > > When I try to boot into FreeBSD (5.0-20000511-CURRENT FreeBSD
> > > 5.0-20000511-CURRENT #4: Thu Jul 6 20:31:41 CDT 2000) I receive:
> > >
> > > Waiting 15 seconds for SCSI devices to settle down
> > > (approximately 30-45 seconds later)
> > > (Probe0:aha0:0:0:0) CCB 0xc782c508
> > > (Probe0:aha0:0:0:0) CCB 0xc782c508
> > > aha0: aha_cmd: Timeout waiting for adapter idle
> > > ahainitmboxes: Initialization command failed
> > > aha0 no longer in timeout
> > > (Probe6:aha0:0:6:0) CCB 0xc782c508
> > > (Probe6:aha0:0:6:0) CCB 0xc782c508
> > > aha0: aha_cmd: Timeout waiting for adapter idle
> > > ahainitmboxes: Initialization command failed
> > > aha0 no longer in timeout
> > >
> > > And it keeps repeating. I had to remove the card to boot into FreeBSD.
> > > The card recognizes the tape drive.
> > >
> > > Any ideas?
> > >
> > > Robert
> > >
> > >
> > > --------------------------------------------------------------------
> > > Does killing time damage eternity?
> > >
> > >
> > >
> > > To Unsubscribe: send mail to [EMAIL PROTECTED]
> > > with "unsubscribe freebsd-questions" in the body of the message
> > >
>
>Ok after further investigation, I can get the system to recognize the card,
>
>aha0 at port-0x130-0x133 irq 9 drq 5 on isa0
>aha0: AHA-1542CF FW Rev. F.0 (ID=45) SCSI Host Adapter, SCSI ID 7, 16 CCBs
>
>but when it does, I get all of these errors
>
> Waiting 15 seconds for SCSI devices to settle down
> (approximately 30-45 seconds later)
> (Probe0:aha0:0:0:0) CCB 0xc782c508
> (Probe0:aha0:0:0:0) CCB 0xc782c508
> aha0: aha_cmd: Timeout waiting for adapter idle
> ahainitmboxes: Initialization command failed
> aha0 no longer in timeout
> (Probe6:aha0:0:6:0) CCB 0xc782c508
> (Probe6:aha0:0:6:0) CCB 0xc782c508
> aha0: aha_cmd: Timeout waiting for adapter idle
> ahainitmboxes: Initialization command failed
> aha0 no longer in timeout
>
>and after 30-45 minutes the system will finally get finished probing and give
>
>me a login prompt.
>
>So it's not an IRQ problem, in fact, the only way I can make the system
>boot-up quickly is to make it share an IRQ. On boot-up, it recognizes and
>lists the tape drive, but when it comes to probing, it's no joy.
>
>Any ideas/suggestions/hints?
To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-current" in the body of the message
