Sometimes when booting after a non-graceful shutdown, the harddisk and cdrom 
drives cause the bootup to hang while probing for them.  Sometimes is finds 
the ad0, but then hangs when it gets to acd0, sometimes it hangs at ad0 too.  
I then have to boot to a pre-ATAng kernel to continue.

-- verbose dmesg --

Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.1-CURRENT #13: Tue Sep  2 00:13:41 EDT 2003
    [EMAIL PROTECTED]:/usr/obj/usr/src/sys/LITTLEGUY
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0416000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0416250.
Calibrating clock(s) ... i8254 clock: 1193167 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 842151665 Hz
CPU: Transmeta(tm) Crusoe(tm) Processor TM5800 (842.15-MHz 586-class CPU)
  Origin = "GenuineTMx86"  Id = 0x543
  Processor revision 1.4.1.0
  Code Morphing Software revision 4.3.0-9-197
  20020207 23:55 official release 4.3.0#7
  LongRun mode: 2  <867MHz 1300mV 100%>
real memory  = 251527168 (239 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009bfff, 634880 bytes (155 pages)
0x000000000043d000 - 0x000000000eb81fff, 242503680 bytes (59205 pages)
avail memory = 239779840 (228 MB)
bios32: Found BIOS32 Service Directory header at 0xc00f6f90
bios32: Entry = 0xfd770 (c00fd770)  Rev = 0  Len = 1
pcibios: PCI BIOS entry at 0xfd770+0x11e
pnpbios: Found PnP BIOS data at 0xc00f6fe0
pnpbios: Entry = f0000:9528  Rev = 1.0
Other BIOS signatures found:
mem: <memory & I/O>
null: <null device, zero device>
random: <entropy source>
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <FUJ    PAULING2> on motherboard
pci_open(1):    mode 1 addr port (0x0cf8) is 0x80003074
pci_open(1a):   mode1res=0x80000000 (0x80000000)
pci_cfgcheck:   device 0 [class=060000] [hdr=80] is there (id=03951279)
pcibios: BIOS version 2.10
Using $PIR table, 9 entries at 0xc00fdf30
PCI-Only Interrupts: none
Location  Bus Device Pin  Link  IRQs
embedded    0    2    A   0x59  3 4 5 7 10 11
embedded    0    4    A   0x08  3 4 5 7 9 10 14 15
embedded    0   12    A   0x01  3 4 5 7 9 10 14 15
embedded    0   16    A   0x02  3 4 5 7 9 10 14 15
embedded    0   18    A   0x05  3 4 5 7 9 10 14 15
embedded    0   18    B   0x06  3 4 5 7 9 10 14 15
embedded    0   19    A   0x03  3 4 5 7 9 10 14 15
embedded    0   20    A   0x04  3 4 5 7 9 10 14 15
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 6 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 7 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 7 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 6 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 18 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 16 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 12 func 0
acpi0: power button is handled as a fixed feature programming model.
ACPI timer looks BAD  min = 2, max = 941, width = 939
ACPI timer looks BAD  min = 2, max = 16, width = 14
ACPI timer looks BAD  min = 2, max = 7, width = 5
ACPI timer looks BAD  min = 2, max = 6, width = 4
ACPI timer looks BAD  min = 2, max = 5, width = 3
ACPI timer looks GOOD min = 2, max = 4, width = 2
ACPI timer looks BAD  min = 2, max = 5, width = 3
ACPI timer looks BAD  min = 2, max = 5, width = 3
ACPI timer looks GOOD min = 2, max = 4, width = 2
ACPI timer looks GOOD min = 2, max = 4, width = 2
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 0 func 0
acpi_timer0: <24-bit timer at 3.579545MHz> port 0xff08-0xff0b on acpi0
acpi_cpu0: <CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
---- initial configuration ------------------------
\\_SB_.PCI0.EIO_.LNKU irq  11: [  3  4  5  7  9 10 11] low,level,sharable 
0.2.0
\\_SB_.PCI0.EIO_.LNKH irq   9: [  3  4  5  7  9 10 11] low,level,sharable 
0.4.0
\\_SB_.PCI0.EIO_.LNKA irq   9: [  3  4  5  7  9 10 11] low,level,sharable 
0.12.0
\\_SB_.PCI0.EIO_.LNKC irq   9: [  3  4  5  7  9 10 11] low,level,sharable 
0.19.0
\\_SB_.PCI0.EIO_.LNKD irq   9: [  3  4  5  7  9 10 11] low,level,sharable 
0.20.0
\\_SB_.PCI0.EIO_.LNKB irq   9: [  3  4  5  7  9 10 11] low,level,sharable 
0.16.0
\\_SB_.PCI0.EIO_.LNKE irq   0: [  3  4  5  7  9 10 11] low,level,sharable 
0.18.0
\\_SB_.PCI0.EIO_.LNKF irq   0: [  3  4  5  7  9 10 11] low,level,sharable 
0.18.1
---- before setting priority for links ------------
\\_SB_.PCI0.EIO_.LNKE:
        interrupts:          3     4     5     7     9    10    11
        penalty:          1220  1220   220  1220   720   220   320
        references:     1
        priority:       0
\\_SB_.PCI0.EIO_.LNKF:
        interrupts:          3     4     5     7     9    10    11
        penalty:          1220  1220   220  1220   720   220   320
        references:     1
        priority:       0
---- before fixup boot-disabled links -------------
\\_SB_.PCI0.EIO_.LNKE:
        interrupts:          3     4     5     7     9    10    11
        penalty:          1220  1220   220  1220   720   220   320
        references:     1
        priority:       734
\\_SB_.PCI0.EIO_.LNKF:
        interrupts:          3     4     5     7     9    10    11
        penalty:          1220  1220   220  1220   720   220   320
        references:     1
        priority:       734
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\\_SB_.PCI0.EIO_.LNKU irq  11: [  3  4  5  7  9 10 11] low,level,sharable 
0.2.0
\\_SB_.PCI0.EIO_.LNKH irq   9: [  3  4  5  7  9 10 11] low,level,sharable 
0.4.0
\\_SB_.PCI0.EIO_.LNKA irq   9: [  3  4  5  7  9 10 11] low,level,sharable 
0.12.0
\\_SB_.PCI0.EIO_.LNKC irq   9: [  3  4  5  7  9 10 11] low,level,sharable 
0.19.0
\\_SB_.PCI0.EIO_.LNKD irq   9: [  3  4  5  7  9 10 11] low,level,sharable 
0.20.0
\\_SB_.PCI0.EIO_.LNKB irq   9: [  3  4  5  7  9 10 11] low,level,sharable 
0.16.0
\\_SB_.PCI0.EIO_.LNKE irq  10: [  3  4  5  7  9 10 11] low,level,sharable 
0.18.0
\\_SB_.PCI0.EIO_.LNKF irq   5: [  3  4  5  7  9 10 11] low,level,sharable 
0.18.1
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
        map[10]: type 1, range 32, base fc000000, size 20, enabled
found-> vendor=0x1279, dev=0x0395, revid=0x02
        bus=0, slot=0, func=0
        class=06-00-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0006, statreg=0x2200, cachelnsz=0 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1279, dev=0x0396, revid=0x00
        bus=0, slot=0, func=1
        class=05-00-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1279, dev=0x0397, revid=0x00
        bus=0, slot=0, func=2
        class=05-00-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        map[10]: type 1, range 32, base fc100000, size 12, enabled
pcib0: matched entry for 0.2.INTA (source \\_SB_.PCI0.EIO_.LNKU)
pcib0: slot 2 INTA is routed to irq 11
found-> vendor=0x10b9, dev=0x5237, revid=0x03
        bus=0, slot=2, func=0
        class=0c-03-10, hdrtype=0x00, mfdev=0
        cmdreg=0x0017, statreg=0x0290, cachelnsz=8 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns)
        intpin=a, irq=11
        powerspec 2  supports D0 D3  current D0
        map[10]: type 4, range 32, base 00001000, size  8, port disabled
        map[14]: type 1, range 32, base fc101000, size 12, memory disabled
pcib0: matched entry for 0.4.INTA (source \\_SB_.PCI0.EIO_.LNKH)
pcib0: slot 4 INTA is routed to irq 9
found-> vendor=0x10b9, dev=0x5451, revid=0x01
        bus=0, slot=4, func=0
        class=04-01-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0000, statreg=0x0290, cachelnsz=0 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x02 (500 ns), maxlat=0x18 (6000 ns)
        intpin=a, irq=9
        powerspec 2  supports D0 D1 D2 D3  current D0
found-> vendor=0x10b9, dev=0x7101, revid=0x00
        bus=0, slot=6, func=0
        class=06-80-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0000, statreg=0x0200, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10b9, dev=0x1533, revid=0x00
        bus=0, slot=7, func=0
        class=06-01-00, hdrtype=0x00, mfdev=0
        cmdreg=0x000f, statreg=0x0210, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        powerspec 1  supports D0 D3  current D0
pcib0: matched entry for 0.12.INTA (source \\_SB_.PCI0.EIO_.LNKA)
pcib0: slot 12 INTA is routed to irq 9
found-> vendor=0x104c, dev=0xac50, revid=0x01
        bus=0, slot=12, func=0
        class=06-07-00, hdrtype=0x02, mfdev=0
        cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0xc0 (48000 ns), maxlat=0x03 (750 ns)
        intpin=a, irq=9
        powerspec 1  supports D0 D1 D2 D3  current D0
        map[20]: type 4, range 32, base 00001400, size  4, enabled
found-> vendor=0x10b9, dev=0x5229, revid=0xc3
        bus=0, slot=15, func=0
        class=01-01-fa, hdrtype=0x00, mfdev=0
        cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
        lattimer=0x20 (960 ns), mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns)
        intpin=a, irq=255
        powerspec 2  supports D0 D3  current D0
        map[10]: type 4, range 32, base 00008000, size  8, enabled
        map[14]: type 1, range 32, base fc102000, size  8, enabled
pcib0: matched entry for 0.16.INTA (source \\_SB_.PCI0.EIO_.LNKB)
pcib0: slot 16 INTA is routed to irq 9
found-> vendor=0x10ec, dev=0x8139, revid=0x10
        bus=0, slot=16, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0003, statreg=0x0290, cachelnsz=0 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x20 (8000 ns), maxlat=0x40 (16000 ns)
        intpin=a, irq=9
        powerspec 2  supports D0 D1 D2 D3  current D0
        map[10]: type 1, range 32, base fc102800, size 11, memory disabled
        map[14]: type 1, range 32, base fc104000, size 14, enabled
pcib0: matched entry for 0.19.INTA (source \\_SB_.PCI0.EIO_.LNKC)
pcib0: slot 19 INTA is routed to irq 9
found-> vendor=0x104c, dev=0x8026, revid=0x00
        bus=0, slot=19, func=0
        class=0c-00-10, hdrtype=0x00, mfdev=0
        cmdreg=0x0010, statreg=0x0210, cachelnsz=8 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns)
        intpin=a, irq=9
        powerspec 2  supports D0 D1 D2 D3  current D0
        map[10]: type 1, range 32, base fd000000, size 24, enabled
        map[14]: type 4, range 32, base 00001800, size  8, enabled
        map[18]: type 1, range 32, base fc103000, size 12, enabled
pcib0: matched entry for 0.20.INTA (source \\_SB_.PCI0.EIO_.LNKD)
pcib0: slot 20 INTA is routed to irq 9
found-> vendor=0x1002, dev=0x4c52, revid=0x64
        bus=0, slot=20, func=0
        class=03-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0087, statreg=0x0290, cachelnsz=8 (dwords)
        lattimer=0x42 (1980 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=9
        powerspec 1  supports D0 D1 D2 D3  current D0
pci0: <memory, RAM> at device 0.1 (no driver attached)
pci0: <memory, RAM> at device 0.2 (no driver attached)
pci0: <serial bus, USB> at device 2.0 (no driver attached)
pci0: <multimedia, audio> at device 4.0 (no driver attached)
pci0: <bridge, PCI-unknown> at device 6.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
pci0: <bridge, PCI-CardBus> at device 12.0 (no driver attached)
atapci0: <AcerLabs Aladdin UDMA66 controller> port 0x1400-0x140f at device 
15.0 on pci0
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0-master: stat=0xd0 err=0xd0 lsb=0xd0 msb=0xd0
ata0-slave: stat=0xd0 err=0xd0 lsb=0xd0 msb=0xd0
ata0-master: stat=0xd0 err=0xd0 lsb=0xd0 msb=0xd0
ata0-slave: stat=0xd0 err=0xd0 lsb=0xd0 msb=0xd0
ata0-master: stat=0xd0 err=0xd0 lsb=0xd0 msb=0xd0
ata0-slave: stat=0xd0 err=0xd0 lsb=0xd0 msb=0xd0
ata0-master: stat=0xd0 err=0xd0 lsb=0xd0 msb=0xd0
ata0-slave: stat=0xd0 err=0xd0 lsb=0xd0 msb=0xd0
ata0-master: stat=0xd0 err=0xd0 lsb=0xd0 msb=0xd0
ata0-slave: stat=0xd0 err=0xd0 lsb=0xd0 msb=0xd0
ata0-master: stat=0xd0 err=0xd0 lsb=0xd0 msb=0xd0
ata0-slave: stat=0xd0 err=0xd0 lsb=0xd0 msb=0xd0
ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0-slave: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 mask=03 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: reset tp3 devices=0x1<ATA_MASTER>
ata0: at 0x1f0 irq 14 on atapci0
ata1: reset tp1 mask=03 ostat0=50 ostat1=00
ata1-master: stat=0xd0 err=0x00 lsb=0x12 msb=0x00
ata1-slave: stat=0xd0 err=0x04 lsb=0xff msb=0xff
ata1-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 mask=03 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER>
ata1: reset tp3 devices=0x4<ATAPI_MASTER>
ata1: at 0x170 irq 15 on atapci0
rl0: <RealTek 8139 10/100BaseTX, rev. C> port 0x8000-0x80ff mem 
0xfc102000-0xfc1020ff irq 9 at device 16.0 on pci0
rl0: Ethernet address: 00:e0:00:ae:45:08
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: bpf attached
pci0: <serial bus, FireWire> at device 19.0 (no driver attached)
pci0: <display, VGA> at device 20.0 (no driver attached)
acpi_button0: <Power Button> on acpi0
acpi_acad0: <AC adapter> on acpi0
acpi_cmbat0: <Control method Battery> on acpi0
acpi_cmbat1: <Control method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
psmcpnp0 irq 12 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x54ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0047
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
acpi_ec0: <embedded controller: GPE 0> port 0x66,0x62 on acpi0
unknown: not probed (disabled)
unknown: not probed (disabled)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xd0000-0xd0fff,0xc0000-0xcffff on isa0
pmtimer0 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0 failed to probe at port 0x3f0 irq 6 drq 2 on isa0
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
ppc0 failed to probe at irq 7 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0 failed to probe at port 0x3f8 irq 4 flags 0x10 on isa0
sio1 failed to probe at port 0x2f8 irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
vga0: vga: WARNING: video mode switching is not fully supported on this 
adapter
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 e7 7e 4f 4f 82 55 03 
b4 1f 00 4f 0d 0e 00 00 07 80 92 88 8f 28 1f 8f
b5 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 e7 7e 4f 4f 82 55 03 
b4 1f 00 4f 0d 0e 00 00 07 80 92 88 8f 28 1f 8f
b5 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 842151665 Hz quality 800
Timecounters tick every 10.000 msec
lo0: bpf attached
acpi_cpu0: set speed to 100.0%
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
acpi_acad0: acline initialization start
acpi_acad0: On Line
acpi_acad0: acline initialization done, tried 1 times
acpi_cmbat0: battery initialization start
acpi_cmbat0: battery initialization done, tried 1 times
acpi_cmbat1: battery initialization start
ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ad0: setting UDMA66 on AcerLabs Aladdin chip
GEOM: create disk ad0 dp=0xc24bae70
ad0: <TOSHIBA MK2018GAP/M1.42 A> ATA-5 disk at ata0-master
ad0: 19077MB (39070080 sectors), 38760 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA66
GEOM: new disk ad0
ata1-master: pio=0x0c wdma=0x22 udma=0x42 cable=80pin
acd0: setting UDMA33 on AcerLabs Aladdin chip
acd0: <TOSHIBA DVD-ROM SD-R2212/1F15> CDRW drive at ata1 as master
acd0: read 4134KB/s (4134KB/s) write 2755KB/s (2755KB/s), 2048KB buffer, 
UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
acd0: Writes: CDR, CDRW, test write, burnproof
acd0: Audio: play, 16 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
[0] f:00 typ:7 s(CHS):0/1/1 e(CHS):1023/2/63 s:63 l:10490382
[1] f:80 typ:165 s(CHS):1023/255/63 e(CHS):1023/9/63 s:10490445 l:20964825
[2] f:00 typ:12 s(CHS):1023/255/63 e(CHS):1023/0/63 s:31455270 l:7598745
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad0s1, start 32256 length 5371075584 end 5371107839
GEOM: Configure ad0s2, start 5371107840 length 10733990400 end 16105098239
GEOM: Configure ad0s3, start 16105098240 length 3890557440 end 19995655679
GEOM: Configure ad0s2a, start 0 length 268435456 end 268435455
GEOM: Configure ad0s2b, start 268435456 length 481656832 end 750092287
GEOM: Configure ad0s2c, start 0 length 10733990400 end 10733990399
GEOM: Configure ad0s2d, start 750092288 length 268435456 end 1018527743
GEOM: Configure ad0s2e, start 1018527744 length 268435456 end 1286963199
GEOM: Configure ad0s2f, start 1286963200 length 9447027200 end 10733990399
Mounting root from ufs:/dev/ad0s2a
start_init: trying /sbin/init
Linux ELF exec handler installed
acpi_cmbat1: battery initialization failed, giving up

--
Anish Mistry

Attachment: pgp00000.pgp
Description: signature

Reply via email to