Hi!
I've just installed 5.1-RELEASE (updated to -current) on a
Dual Opteron 1.4 with 6GB memory installed (MSI K8D Master-F).
Without 'options PAE' the system works fine (beside the 'missing' 2GB).
Enabling PAE in a custom kernel (device acpi, options SMP, options APIC_IO
and makeoptions NO_MODULES=yes) leads to a crash on boot before
printing the amount of memory (sorry no tip output). When disabling
acpi it displays the 6140MB but fails to pass
"Programming 4 pins in IOAPIC #2".
The PAE-GENERIC kernel loads and then immediately reboots before
printing one line.
Any hints?
Thanks, Hendrik
Here is the dmesg (onboard dual bge works but disabled)
and mptable output:
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.1-CURRENT #0: Wed Oct 1 21:11:28 EDT 2003
[EMAIL PROTECTED]:/usr/src/sys/i386/compile/READER
Preloaded elf kernel "/boot/kernel.4gb/kernel" at 0xc0782000.
Preloaded elf module "/boot/kernel.4gb/acpi.ko" at 0xc0782220.
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Opteron(tm) Processor 240 (1395.66-MHz 686-class CPU)
Origin = "AuthenticAMD" Id = 0xf51 Stepping = 1
Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CM
OV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
AMD Features=0xe0500000<<b20>,AMIE,<b29>,DSP,3DNow!>
real memory = 4227792896 (4031 MB)
avail memory = 4113760256 (3923 MB)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
Programming 4 pins in IOAPIC #1
Programming 4 pins in IOAPIC #2
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): apic id: 0, version: 0x00040010, at 0xfee00000
cpu1 (AP): apic id: 1, version: 0x00040010, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000
io1 (APIC): apic id: 3, version: 0x00030011, at 0xfebff000
io2 (APIC): apic id: 4, version: 0x00030011, at 0xfebfe000
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <A M I OEMRSDT > on motherboard
pcibios: BIOS version 2.10
Using $PIR table, 12 entries at 0xc00f27d0
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x5008-0x500b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_cpu1: <CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
IOAPIC #0 intpin 19 -> irq 2
pcib1: <ACPI PCI-PCI bridge> at device 6.0 on pci0
pci1: <ACPI PCI bus> on pcib1
IOAPIC #0 intpin 18 -> irq 9
IOAPIC #0 intpin 16 -> irq 10
pci1: <serial bus, USB> at device 0.0 (no driver attached)
pci1: <serial bus, USB> at device 0.1 (no driver attached)
pci1: <display, VGA> at device 6.0 (no driver attached)
atapci0: <Promise PDC20318 SATA150 controller> port 0xb400-0xb47f,0xb480-0xb48f,
0xbc00-0xbc3f mem 0xfe8a0000-0xfe8bffff,0xfe8fe000-0xfe8fefff irq 10 at device 8
.0 on pci1
atapci0: [MPSAFE]
ata2: at 0xfe8fe000 on atapci0
ata2: [MPSAFE]
ata3: at 0xfe8fe000 on atapci0
ata3: [MPSAFE]
ata4: at 0xfe8fe000 on atapci0
ata4: [MPSAFE]
ata5: at 0xfe8fe000 on atapci0
ata5: [MPSAFE]
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <AMD 8111 UDMA133 controller> port 0xffa0-0xffaf at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci1
ata0: [MPSAFE]
ata1: at 0x170 irq 15 on atapci1
ata1: [MPSAFE]
pci0: <serial bus, SMBus> at device 7.2 (no driver attached)
pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 10.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pci0: <base peripheral, interrupt controller> at device 10.1 (no driver attached
)
pcib3: <ACPI PCI-PCI bridge> at device 11.0 on pci0
pci3: <ACPI PCI bus> on pcib3
IOAPIC #2 intpin 0 -> irq 11
ti0: <Alteon AceNIC 1000baseSX Gigabit Ethernet> mem 0xfeafc000-0xfeafffff irq 1
1 at device 1.0 on pci3
ti0: Ethernet address: 00:60:cf:20:6b:99
pci0: <base peripheral, interrupt controller> at device 11.1 (no driver attached
)
acpi_button0: <Power Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0
x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
pmtimer0 on isa0
orm0: <Option ROMs> at iomem 0xc8000-0xcafff,0xc0000-0xc7fff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
Timecounters tick every 10.000 msec
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
acd0: CDROM <FX54++M> at ata0-master PIO4
GEOM: create disk ad4 dp=0xcb277470
ad4: 76319MB <ST380013AS> [155061/16/63] at ata2-master UDMA133
SMP: AP CPU #1 Launched!
Mounting root from ufs:/dev/ad4s1a
ti0: gigabit link up
===============================================================================
MPTable, version 2.0.15
-------------------------------------------------------------------------------
MP Floating Pointer Structure:
location: BIOS
physical address: 0x000ff780
signature: '_MP_'
length: 16 bytes
version: 1.1
checksum: 0x45
mode: Virtual Wire
-------------------------------------------------------------------------------
MP Config Table Header:
physical address: 0x000f9fb0
signature: 'PCMP'
base table length: 308
version: 1.1
checksum: 0x13
OEM ID: 'MSI '
Product ID: 'RHAPSODY '
OEM table pointer: 0x00000000
OEM table size: 0
entry count: 30
local APIC address: 0xfee00000
extended table length: 0
extended table checksum: 0
-------------------------------------------------------------------------------
MP Config Base Table Entries:
--
Processors: APIC ID Version State Family Model Step Flags
0 0x10 BSP, usable 15 5 1 0x78bfb
ff
1 0x10 AP, usable 15 5 1 0x78bfb
ff
--
Bus: Bus ID Type
0 PCI
1 PCI
2 PCI
3 PCI
4 ISA
--
I/O APICs: APIC ID Version State Address
2 0x11 usable 0xfec00000
3 0x11 usable 0xfebff000
4 0x11 usable 0xfebfe000
--
I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
ExtINT active-hi edge 4 0 2 0
INT active-hi edge 4 1 2 1
INT active-hi edge 4 0 2 2
INT active-hi edge 4 3 2 3
INT active-hi edge 4 4 2 4
INT active-hi edge 4 5 2 5
INT active-hi edge 4 6 2 6
INT active-hi edge 4 7 2 7
INT active-hi edge 4 8 2 8
INT active-hi edge 4 12 2 12
INT active-hi edge 4 13 2 13
INT active-hi edge 4 14 2 14
INT active-hi edge 4 15 2 15
INT active-lo level 0 7:D 2 19
INT active-lo level 1 0:D 2 19
INT active-lo level 1 8:A 2 16
INT active-lo level 1 6:A 2 18
INT active-lo level 3 1:A 4 0
--
Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
ExtINT active-hi edge 0 0:A 255 0
NMI active-hi edge 0 0:A 255 1
===============================================================================
--
Hendrik Scholz - <[EMAIL PROTECTED]> - http://raisdorf.net/
drag me, drop me - treat me like an object
_______________________________________________
[EMAIL PROTECTED] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
