Hi all,
I have a problem with a server running a FreeBSD 3.2.
My Server has a L440GX+ Serber Board (intel), with network card 10/100,
SCSI AIC 7896 (80MB/s), 2 SCSI disk with 9GB (80MB/s), 2 pentium III
450Mhz (not overclocked). The NIC and SCSI are onboard.
I recompiled a kernel to SMP, and it worked. The server is ok, but when I
run a comand with disk access (whith vipw or mysql), the performance of
server goes down. My server stays very very very slow. If I use pine to
read my messages, it doesn't work. When the comand finishes, the server
stays "ok" again.
I recompiled the kernel with "maxusers 128", but it doesn't work.
My SCSI cable has a terminator and the scsi setup is ok (I think :) ).
The dmesg command output is in attchmnt.
I appreciate any help.
[]s,
Luiz Morte da Costa Junior
Analista de Redes E-mail: mo...@correionet.com.br
Telefone: +55 19 754-2532 Fax: +55 19 255-7576
CorreioNet - Correio Popular Campinas - SP - Brazil
Copyright (c) 1992-1999 FreeBSD Inc.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 3.2-RELEASE #1: Wed Aug 18 17:42:50 EST 1999
r...@caxton.correionet.com.br:/usr/src/sys/compile/DUAL
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III (686-class CPU)
Origin = "GenuineIntel" Id = 0x672 Stepping=2
Features=0x387fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,<b18>,MMX,<b24>,<b25>>
real memory = 536870912 (524288K bytes)
config> di zp0
config> di ze0
config> di lnc0
config> di le0
config> di ie0
config> di fe0
config> di ex0
config> di ep0
config> di ed0
config> di cs0
config> di scd0
config> di mcd0
config> q
avail memory = 519188480 (507020K bytes)
Programming 24 pins in IOAPIC #0
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 1, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000
Preloaded elf kernel "kernel" at 0xc0366000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc036609c.
Probing for devices on PCI bus 0:
chip0: <Intel 82443GX host to PCI bridge> rev 0x00 on pci0.0.0
chip1: <Intel 82443GX host to AGP bridge> rev 0x00 on pci0.1.0
ahc0: <Adaptec aic7896/97 Ultra2 SCSI adapter> rev 0x00 int a irq 19 on
pci0.12.0
ahc0: aic7896/97 Wide Channel A, SCSI Id=7, 16/255 SCBs
ahc1: <Adaptec aic7896/97 Ultra2 SCSI adapter> rev 0x00 int a irq 19 on
pci0.12.1
ahc1: aic7896/97 Wide Channel B, SCSI Id=7, 16/255 SCBs
fxp0: <Intel EtherExpress Pro 10/100B Ethernet> rev 0x08 int a irq 21 on
pci0.14.0
fxp0: Ethernet address 00:a0:c9:fc:17:55
chip2: <Intel 82371AB PCI to ISA bridge> rev 0x02 on pci0.18.0
ide_pci0: <Intel PIIX4 Bus-master IDE controller> rev 0x01 on pci0.18.1
chip3: <Intel 82371AB Power management controller> rev 0x02 on pci0.18.3
vga0: <Cirrus Logic model 00bc VGA-compatible display device> rev 0x23 on
pci0.20.0
Probing for devices on PCI bus 1:
chip4: <PCI to PCI bridge (vendor=1011 device=0023)> rev 0x06 on pci1.15.0
Probing for devices on PCI bus 2:
Probing for PnP devices:
Probing for devices on the ISA bus:
sc0 on isa
sc0: VGA color <16 virtual consoles, flags=0x0>
atkbdc0 at 0x60-0x6f on motherboard
atkbd0 irq 1 on isa
psm0 not found
sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa
sio0: type 16550A
sio1 at 0x2f8-0x2ff irq 3 on isa
sio1: type 16550A
fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
fdc0: FIFO enabled, 8 bytes threshold
fd0: 1.44MB 3.5in
wdc0 not found at 0x1f0
wdc1 at 0x170-0x177 irq 15 on isa
wdc1: unit 0 (atapi): <CREATIVECD4831E/1.00>, removable, accel, dma, iordis
acd0: drive speed 2755 - 5511KB/sec, 240KB cache
acd0: supported read types: CD-R, CD-RW, CD-DA
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray
acd0: Medium: no/blank disc inside, unlocked
wt0 not found at 0x300
matcdc0 not found at 0x230
ppc0 at 0x378 irq 7 flags 0x40 on isa
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
lpt0: <generic printer> on ppbus 0
lpt0: Interrupt-driven port
ppi0: <generic parallel i/o> on ppbus 0
plip0: <PLIP network interface> on ppbus 0
lpt0: <generic printer> on ppbus 0
lpt0: Interrupt-driven port
adv0 not found at 0x330
bt_isa_probe: Probe failled for card at 0x330
bt_isa_probe: Probe failled for card at 0x334
bt_isa_probe: Probe failled for card at 0x230
bt_isa_probe: Probe failled for card at 0x234
bt_isa_probe: Probe failled for card at 0x130
bt_isa_probe: Probe failled for card at 0x134
bt0 not found at 0x134
aha0 not found at 0x134
vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa
npx0 on motherboard
npx0: INT 16 interface
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via pin 2
Waiting 15 seconds for SCSI devices to settle
SMP: AP CPU #1 Launched!
sa0 at ahc1 bus 0 target 4 lun 0
sa0: <HP C1537A L706> Removable Sequential Access SCSI-2 device
sa0: 10.000MB/s transfers (10.000MHz, offset 32)
da0 at ahc0 bus 0 target 0 lun 0
da0: <SEAGATE ST39140LW 1483> Fixed Direct Access SCSI-2 device
da0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da0: 8683MB (17783240 512 byte sectors: 255H 63S/T 1106C)
da1 at ahc0 bus 0 target 1 lun 0
da1: <SEAGATE ST39140LW 1483> Fixed Direct Access SCSI-2 device
da1: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da1: 8683MB (17783240 512 byte sectors: 255H 63S/T 1106C)
changing root device to da0s1a
(da1:ahc0:0:1:0): READ(06). CDB: 8 1 8b 46 a 0
(da1:ahc0:0:1:0): RECOVERED ERROR asc:5d,32
(da1:ahc0:0:1:0): Reserved ASC/ASCQ pair
pid 36798 (pine), uid 4472: exited on signal 6 (core dumped)
