Dear Stefan, Thanks for your help. I've attached the information you requested. In particular, here are the relevant sections of the dmesg output:
pcib5: <ACPI PCI-PCI bridge> at device 11.0 on pci8
pcib5: secondary bus 10
pcib5: subordinate bus 10
pcib5: I/O decode 0xf000-0xfff
pcib5: memory decode 0xde100000-0xde1fffff
pcib5: prefetched decode 0xfff00000-0xfffff
pci10: <ACPI PCI bus> on pcib5
pci10: physical bus=10
found-> vendor=0x14e4, dev=0x1648, revid=0x10
bus=10, slot=9, func=0
class=02-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0116, statreg=0x02b0, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
MSI supports 8 messages, 64 bit
map[10]: type 1, range 64, base de100000, size 16, enabled
pcib5: memory: end (de1fffff) < start (49dbdf2de100000)
pcib5: (null) requested unsupported memory range 0x0-0x0 (decoding
0xde100000-0xde1fffff, 0xfff00000-0xfffff)
pcib5: matched entry for 10.9.INTA
pcib5: slot 9 INTA hardwired to IRQ 28
found-> vendor=0x14e4, dev=0x1648, revid=0x10
bus=10, slot=9, func=1
class=02-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0116, statreg=0x02b0, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns)
intpin=b, irq=11
powerspec 2 supports D0 D3 current D0
MSI supports 8 messages, 64 bit
map[10]: type 1, range 64, base de110000, size 16, enabled
pcib5: memory: end (de1fffff) < start (dbfa72fdde110000)
pcib5: (null) requested unsupported memory range 0x0-0x0 (decoding
0xde100000-0xde1fffff, 0xfff00000-0xfffff)
pcib5: matched entry for 10.9.INTB
pcib5: slot 9 INTB hardwired to IRQ 29
bge0: <Broadcom BCM5704 B0, ASIC rev. 0x2100> mem
0x49dbdf2de100000-0x49dbdf2de10ffff irq 28 at device 9.0 on pci10
pcib5: memory: end (de1fffff) < start (49dbdf2de100000)
pcib5: bge0 requested unsupported memory range 0x0-0x0 (decoding
0xde100000-0xde1fffff, 0xfff00000-0xfffff)
bge0: couldn't map memory
device_attach: bge0 attach returned 6
bge1: <Broadcom BCM5704 B0, ASIC rev. 0x2100> mem
0xdbfa72fdde110000-0xdbfa72fdde11ffff irq 29 at device 9.1 on pci10
pcib5: memory: end (de1fffff) < start (dbfa72fdde110000)
pcib5: bge1 requested unsupported memory range 0x0-0x0 (decoding
0xde100000-0xde1fffff, 0xfff00000-0xfffff)
bge1: couldn't map memory
device_attach: bge1 attach returned 6
pci8: <base peripheral, interrupt controller> at device 11.1 (no
driver attached)
Any help you could provide would be greatly appreciated!
Thanks again,
James
On 7/16/07, Stefan Esser <[EMAIL PROTECTED]> wrote:
James Shank schrieb: > Greetings, > > I've run into a problem with the onboard Broadcom 5704 NetXtreme nics > on a Tyan S2891 Thunder K8SRE motherboard. > > Here is the relevant dmesg output to show the error: > > pcib5: <ACPI PCI-PCI bridge> at device 11.0 on pci8 > pci10: <ACPI PCI bus> on pcib5 > pcib5: memory: end (de1fffff) < start (48739b2de100000) > pcib5: memory: end (de1fffff) < start (dbca73fdde110000) > bge0: <Broadcom BCM5704 B0, ASIC rev. 0x2100> mem > 0x48739b2de100000-0x48739b2de10ffff irq 28 at device 9.0 on pci10 > pcib5: memory: end (de1fffff) < start (48739b2de100000) Hi James, the information that you provided is not sufficient to diagnose this problem. You should post a *verbose* boot message log (via the boot loader menu or the loader command "boot -v"). Please do also provide a dump of the config registers of the PCI bridge for which the error condition is reported: # pciconf -r pci8:11:0 0:0x3f // device 11.0 on pci8 Not sure that I'll have time to look into this right today, but others on the list will want the same information so you may want to post it there ... This looks like a problem with the PCI bridge code, not the device init code, actually. But just in case it is not, you could also provide a register dump of the Ethernet chip: # pciconf -r pci10:9:0 0:0x3f Regards, STefan
dmesg.boot-v.out
Description: Binary data
pciconf-r.out
Description: Binary data
_______________________________________________ [email protected] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-hackers To unsubscribe, send any mail to "[EMAIL PROTECTED]"
