On Tue, 21-Aug-2001 at 23:44:40 -0600, Warner Losh wrote:
> In message <[EMAIL PROTECTED]> Andre Albsmeier writes:
> : I still have the hangs on a warm reboot but this is a different
> : story...
>
> Eh? what kind of hangs and when?
Attached below is the dmesg... It hangs only when warm booting; after
a power toggle everything is OK...
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.4-RC #23: Wed Aug 22 07:21:34 CEST 2001
[EMAIL PROTECTED]:/src/obj-4/src/src-4/sys/schlappy
Calibrating clock(s) ... TSC clock: 366660160 Hz, i8254 clock: 1193146 Hz
Timecounter "i8254" frequency 1193146 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (366.66-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x66a Stepping = 10
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 134152192 (131008K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x00325000 - 0x07febfff, 130838528 bytes (31943 pages)
avail memory = 127590400 (124600K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00f6230
bios32: Entry = 0xfd790 (c00fd790) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0x225
pnpbios: Found PnP BIOS data at 0xc00f6260
pnpbios: Entry = f0000:a34e Rev = 1.0
pnpbios: Event flag at 4b4
Other BIOS signatures found:
ACPI: 000f61f0
Preloaded elf kernel "kernel" at 0xc02ff000.
Pentium Pro MTRR support enabled
pci_open(1): mode 1 addr port (0x0cf8) is 0x8000384c
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71908086)
Using $PIR table, 7 entries at 0xc00fdf50
apm0: <APM BIOS> on motherboard
apm: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
found-> vendor=0x8086, dev=0x7190, revid=0x03
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base f8000000, size 26
found-> vendor=0x8086, dev=0x7191, revid=0x03
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=1 secondarybus=1
found-> vendor=0x8086, dev=0x7110, revid=0x02
class=06-80-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x7111, revid=0x01
class=01-01-80, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 0000fcd0, size 4
found-> vendor=0x8086, dev=0x7112, revid=0x01
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=9
map[20]: type 1, range 32, base 0000fce0, size 5
found-> vendor=0x8086, dev=0x7113, revid=0x02
class=06-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[90]: type 1, range 32, base 00002180, size 4
found-> vendor=0x104c, dev=0xac1c, revid=0x01
class=06-07-00, hdrtype=0x02, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=10
found-> vendor=0x104c, dev=0xac1c, revid=0x01
class=06-07-00, hdrtype=0x02, mfdev=1
subordinatebus=0 secondarybus=0
intpin=b, irq=11
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
found-> vendor=0x10c8, dev=0x0005, revid=0x12
class=03-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base f6000000, size 24
map[14]: type 1, range 32, base fe400000, size 22
map[18]: type 1, range 32, base feb00000, size 20
found-> vendor=0x10c8, dev=0x8005, revid=0x12
class=04-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=b, irq=11
map[10]: type 1, range 32, base f7800000, size 22
map[14]: type 1, range 32, base fea00000, size 20
pci1: <PCI bus> on pcib1
pci1: <NeoMagic MagicMedia 256AV SVGA controller> (vendor=0x10c8, dev=0x0005) at 0.0
irq 10
chip1: <NeoMagic MagicMedia 256AX Audio controller> mem
0xfea00000-0xfeafffff,0xf7800000-0xf7bfffff irq 11 at device 0.1 on pci1
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xfcd0-0xfcdf at device 7.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xfcd0
ata0: mask=03 status0=50 status1=50
ata0: mask=03 ostat0=50 ostat2=50
ata0-slave: ATAPI probe a=14 b=eb
ata0-master: ATAPI probe a=00 b=00
ata0: mask=03 status0=50 status1=00
ata0-master: ATA probe a=01 b=a5
ata0: devices=09
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xfcd8
ata1: mask=00 status0=ff status1=ff
ata1: probe allocation failed
pci0: <Intel 82371AB/EB (PIIX4) USB controller> (vendor=0x8086, dev=0x7112) at 7.2 irq
9
chip2: <Intel 82371AB Power management controller> port 0x2180-0x218f at device 7.3 on
pci0
pcic0: <TI PCI-1225 PCI-CardBus Bridge> irq 10 at device 10.0 on pci0
pcic0: PCI Memory allocated: 0x44000000
pcic0: TI12XX PCI Config Reg: [ring enable][speaker enable][pwr save][CSC serial isa
irq]
pccard0: <PC Card bus (classic)> on pcic0
pcic1: <TI PCI-1225 PCI-CardBus Bridge> irq 11 at device 10.1 on pci0
pcic1: PCI Memory allocated: 0x44001000
pcic1: TI12XX PCI Config Reg: [ring enable][speaker enable][pwr save][CSC serial isa
irq]
pccard1: <PC Card bus (classic)> on pcic1
ata-: ata0 exists, using next available unit number
ata-: ata1 exists, using next available unit number
pcic-: pcic0 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROM> at iomem 0xc0000-0xcbfff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0045
atkbd: keyboard ID 0x41ab (2)
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
psm0: current command byte:0045
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0-00, 3 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
vga0: <Generic ISA VGA> at port 0x3b0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7006d
fb0: port:0x3b0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> on isa0
sc0: VGA <9 virtual consoles, flags=0x200>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
ata2 failed to probe at port 0x1f0 irq 14 on isa0
ata3: iobase=0x0170 altiobase=0x0376 bmaddr=0x0000
ata3: mask=00 status0=ff status1=ff
ata3: probe allocation failed
ata3 failed to probe at port 0x170-0x177,0x376 irq 15 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: irq maps: 0xc41 0xc51 0xc41 0xc41
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0xc41 0xc49 0xc41 0xc41
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
mss_detect - chip revision 0x0a
mss_detect() - Detected OPL3-SAx (YMF719)
pcm0: <OPL3-SAx (YMF719)> at port 0x530-0x537,0x370-0x371,0xf8c-0xf94,0xe0e irq 5 drq
1 flags 0xc113 on isa0
Yamaha: ver 0x21 DMA config 0x8f
pcm: setmap c000, 1000; 0xc75f3000 -> c000
pcm: setmap d000, 1000; 0xc75f4000 -> d000
pcic2 failed to probe at port 0x3e0-0x3e1 on isa0
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
PC873xx probe at 0x398 got unknown ID 0xb2
ppc0: SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
isa_probe_children: probing PnP devices
pcic0: Event mask 0xf stat 0x30000419
###############################################
### Now it hangs until poweroff/poweron ###
###############################################
pcic1: Event mask 0xf stat 0x30000459
BIOS Geometries:
0:03feef3f 0..1022=1023 cylinders, 0..239=240 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: lo0 attached
ata0-master: DMA limited to UDMA33, non-ATA66 compliant cable
ata0-master: success setting UDMA2 on Intel chip
Creating DISK ad0
ad0: <IBM-DJSA-230/JS6OAC3A> ATA-5 disk at ata0-master
ad0: 28615MB (58605120 sectors), 58140 cyls, 16 heads, 63 S/T, 512 B/S
ad0: 16 secs/int, 1 depth queue, UDMA33
ad0: piomode=4 dmamode=2 udmamode=4 cblid=0
ad0: 28615MB <IBM-DJSA-230> [58140/16/63] at ata0-master UDMA33
ata0-slave: piomode=4 dmamode=2 udmamode=-1 dmaflag=1
ata0-slave: success setting PIO4 on generic chip
acd0: <MATSHITADVD-ROM SR-8171/079G> DVD-ROM drive at ata0 as slave
acd0: read 3437KB/s (3437KB/s), 512KB buffer, PIO4
acd0: Reads: CD-R, CD-RW, CD-DA stream, DVD-ROM, packet
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray
acd0: Medium: no/blank disc inside, unlocked
Mounting root from ufs:/dev/ad0s2a
pccard: card inserted, slot 0
pccard: card inserted, slot 1
ad0s1: type 0x6, start 63, end = 4192964, size 4192902 : OK
ad0s2: type 0xa5, start 4192965, end = 58605056, size 54412092 : OK
start_init: trying /sbin/init
pccard: card inserted, slot 0
pccard: card inserted, slot 1
pccard0: Assigning xe0: io 0x240-0x24f irq 10 mem 0xd4000-0xd4fff
xe0 at port 0x240-0x24f iomem 0xcc000-0xccfff irq 10 slot 0 on pccard0
pcic: I/O win 0 flags 17 240-24f
xe0: Forcing IRQ to 10
using shared irq10.
xe0: Intel CE3, bonding version 0x45, 100Mbps capable
xe0: DingoID = 0x444b, RevisionID = 0x1, VendorID = 0
xe0: Ethernet address 00:a0:c9:bb:80:26
bpf: xe0 attached
sio-: sio0 exists, using next available unit number
pccard1: Assigning sio2: io 0x2e8-0x2ef irq 11 mem 0x0-0xffffffff
pcic: I/O win 0 flags 17 2e8-2ef
pcic: I/O win 0 flags 7 2e8-2ef
sio2 at port 0x2e8-0x2ef irq 11 slot 1 on pccard1
pcic: I/O win 0 flags 17 2e8-2ef
sio2: type 16550A
sio2: Forcing IRQ to 11
using shared irq11.
Linux-ELF exec handler installed
To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-net" in the body of the message
