Hi Mark, >>This snippet is from a script, and the variables '$if1' and '$if2' >>are set to the interfaces. In effect, the 'connect' lines above are actually (for Neterion 10Gig driver): >>ngctl connect xge0: ngeth0:lower lower many0 ngctl connect xge1: ngeth0:lower lower many0
Can You please send me the steps/command that you used to test the Neterion card. I means what are the argument that you gave for msg command. Info on how did you verify the traffic flow? Thanks, ~Siva -----Original Message----- From: Gleb Smirnoff [mailto:[EMAIL PROTECTED] Sent: Friday, August 18, 2006 3:26 PM To: SIVAKUMAR SUBRAMANI (WT01 - Computing Systems & Storage) Cc: [EMAIL PROTECTED]; [EMAIL PROTECTED]; freebsd-net@FreeBSD.org Subject: Re: netgraph with 10Gig interfaces On Thu, Aug 17, 2006 at 06:21:50PM +0530, [EMAIL PROTECTED] wrote: s> I have bge and fxp interface on the system. I enabled the NETGRAPH by s> enabling the NETGRAPH in the config file and compiled the new kernel. s> Then, booted with the new kernel. s> s> s> fxp0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 s> options=8<VLAN_MTU> s> inet6 fe80::290:27ff:fe85:8b8c%fxp0 prefixlen 64 scopeid 0x1 s> inet 17.1.1.150 netmask 0xff000000 broadcast 17.255.255.255 s> ether 00:90:27:85:8b:8c s> media: Ethernet autoselect (none) s> status: no carrier s> s> bge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 s> options=1a<TXCSUM,VLAN_MTU,VLAN_HWTAGGING> s> inet6 fe80::2e0:81ff:fe29:f38d%bge0 prefixlen 64 scopeid 0x3 s> inet 10.114.52.152 netmask 0xffffff00 broadcast 10.114.52.255 s> ether 00:e0:81:29:f3:8d s> media: Ethernet autoselect (100baseTX <full-duplex>) s> status: active s> s> Even then I could not see the above interfaces listed in the output s> of the list command of ngctl. s> s> + list -l s> There are 2 total nodes: s> Name: ngctl1088 Type: socket ID: 00000007 Num hooks: s> 0 s> Name: <unnamed> Type: eiface ID: 00000004 Num hooks: s> 0 s> + list -n s> There are 1 total named nodes: s> Name: ngctl1088 Type: socket ID: 00000007 Num hooks: s> 0 s> + s> s> s> But as per the document in the below link it is mentioned that s> network interface by default should be listed in the output. s> http://ezine.daemonnews.org/200003/netgraph.html s> s> Is that means these drivers are not supporting the netgraph? No. You need either kldload ng_ether or add NETGRAPH_ETHER to kernel config. -- Totus tuus, Glebius. GLEBIUS-RIPN GLEB-RIPE The information contained in this electronic message and any attachments to this message are intended for the exclusive use of the addressee(s) and may contain proprietary, confidential or privileged information. If you are not the intended recipient, you should not disseminate, distribute or copy this e-mail. Please notify the sender immediately and destroy all copies of this message and any attachments. WARNING: Computer viruses can be transmitted via email. The recipient should check this email and any attachments for the presence of viruses. The company accepts no liability for any damage caused by any virus transmitted by this email. www.wipro.com _______________________________________________ freebsd-net@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-net To unsubscribe, send any mail to "[EMAIL PROTECTED]"
