David Christensen wrote: > Oliver Fromme wrote: > > While trying to debug the same issue I stumbled across this > > thread ... We've got HS22 blades (IBM BladeCenter) which > > habe the BCM5709S and suffer from exactly the same problem. > > > > Dave, are there any news regarding the PHY implementation? > > > > If there's decent documentation I might even give it a try > > myself, provided that it's not too complex. (I've done > > hardware programming before, but I've never touched a NIC/PHY > > driver, except for very trivial fixes.) > > > > Pyunh has taken an active interest in this effort and sent out > a patch yesterday, though he doesn't have hardware to test. I'm > planning on giving his patch a try today to see how close he got > on his first attempt.
Thank you very much to both of you! With that patch applied, the 5709S PHY is correctly attached by brgphy and "seems to work". I can't test it thoroughly right now, though, because there is no cable attached to the port ... The machine is located in a customer's datacenter in a different city and I'll have to ask someone to connect the ports. This is a little bit complicated in that company. :-) I will continue testing as soon as there's a physical link. For now, this is what ifconfig says (bce0 only; bce1 is the same): bce0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=1bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4> capabilities=1bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4> ether 00:21:5e:98:f6:6c media: Ethernet autoselect (autoselect <half-duplex>) status: no carrier supported media: media autoselect media 1000baseSX mediaopt full-duplex media none Here's an excerpt from dmesg (verbose boot): bce0: <Broadcom NetXtreme II BCM5709 1000Base-SX (C0)> mem 0x92000000-0x93ffffff irq 30 at device 0.0 on pci16 bce0: attempting to allocate 1 MSI vectors (16 supported) msi: routing MSI IRQ 260 to local APIC 0 vector 112 bce0: using IRQ 260 for MSI miibus2: <MII bus> on bce0 brgphy2: <BCM5709S 1000/2500baseSX PHY> PHY 2 on miibus2 brgphy2: OUI 0x0050ef, model 0x003f, rev. 0 brgphy2: 1000baseSX-FDX, auto bce0: bpf attached bce0: Ethernet address: 00:21:5e:98:f6:6c bce0: [MPSAFE] bce0: [ITHREAD] bce0: ASIC (0x57092000); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.0.6); Flags (MSI|MFW); MFW (NCSI 2.0.3) And relevant parts from devinfo -rv: pcib6 pnpinfo vendor=0x8086 device=0x340e subvendor=0x1014 subdevice=0x340e class=0x060400 at slot=7 function=0 handle=\_SB_.PCI0.ETH1 pci16 bce0 pnpinfo vendor=0x14e4 device=0x163a subvendor=0x1014 subdevice=0x0370 class=0x020000 at slot=0 function=0 Interrupt request lines: 260 I/O memory addresses: 0x92000000-0x93ffffff miibus2 brgphy2 pnpinfo oui=0x50ef model=0x3f rev=0x0 at phyno=2 Finally pciconf -lcv: b...@pci0:16:0:0: class=0x020000 card=0x03701014 chip=0x163a14e4 rev=0x20 hdr=0x00 vendor = 'Broadcom Corporation' device = 'NetXtreme II BCM5709S Gigabit Ethernet' class = network subclass = ethernet cap 01[48] = powerspec 3 supports D0 D3 current D0 cap 03[50] = VPD cap 05[58] = MSI supports 16 messages, 64 bit enabled with 1 message cap 11[a0] = MSI-X supports 9 messages in map 0x10 cap 10[ac] = PCI-Express 2 endpoint max data 256(512) link x4(x4) The complete files (dmesg etc.) can be found here: http://www.secnetix.de/olli/dmesg/hs22/ Best regards Oliver -- Oliver Fromme, secnetix GmbH & Co. KG, Marktplatz 29, 85567 Grafing b. M. Handelsregister: Registergericht Muenchen, HRA 74606, Geschäftsfuehrung: secnetix Verwaltungsgesellsch. mbH, Handelsregister: Registergericht Mün- chen, HRB 125758, Geschäftsführer: Maik Bachmann, Olaf Erb, Ralf Gebhart FreeBSD-Dienstleistungen, -Produkte und mehr: http://www.secnetix.de/bsd "IRIX is about as stable as a one-legged drunk with hypothermia in a four-hundred mile per hour wind, balancing on a banana peel on a greased cookie sheet -- when someone throws him an elephant with bad breath and a worse temper." -- Ralf Hildebrandt _______________________________________________ freebsd-net@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-net To unsubscribe, send any mail to "freebsd-net-unsubscr...@freebsd.org"