On Mon, Oct 31, 2011 at 08:57:46PM -0500, Paul A. Procacci wrote: > Gents, > > I'm having quite an aweful problem that I need a bit of help with. > > I have an HPDL360 G3 ( > http://h18000.www1.hp.com/products/quickspecs/11504_na/11504_na.HTML ) which > acts as a NAT (via PF) for several (600+) class C's amongst 24+ machines > sitting behind it. > It's running FPSense (FreeBSD 8.1-RELEASE-p4). > > The important guts are: > > 2 x 2.8 GHz Cpus > 2 BGE interfaces on a PCI-X bus. > > During peak times this machine is only able to handle between 500Mbps - > 600Mbps before running out of cpu capacity. (300Mbps(ish) on the LAN, > 300Mbps(ish) on the WAN) It's due to the high number of interrupts. > I was speaking with a networking engineer here and he mentioned that I should > look at "Interrupt Coalescing" to increase throughput. > The only information I found online regarding this was a post from 2 years > ago here: http://lists.freebsd.org/pipermail/freebsd-net/2009-June/022227.html > > The tunables mentioned in the above post aren't present in my system, so I > imagine this never made it into the bge driver. Assuming this to be the > case, I started looking at DEVICE_POLLING as a solution. > I did try implementing device polling, but the results were worse than I > expected. netisr was using 100% of a single cpu while the other cpu remained > mostly idle. > Not knowing exactly what netisr is, I reverted the changes. > > This leads me to this list. Given the scenario above, I'm nearly certain I > need to use device polling instead of the standard interrupt driven setup. > The two sysctl's that I've come across thus far that I think are what I need > are: > > net.isr.maxthreads > hern.hz > > I would assume setting net.isr.maxthreads to 2 given my dual core machine is > advisable, but I'm not 100% sure. > What are the caveats in setting this higher? Given the output of `sysctl -d > net.isr.maxthreads` I would expect anything higher than the number of cores > to be detrimental. Is this correct? > > kern.hz I'm more unsure of. I understand what the sysctl is, but I'm not > sure how to come up with a reasonable number. > Generally speaking, and in your experience, would a setting of 2000 achive > close to the theoritical meximum of the cards? Is there an upper limit that > I would be worried about? > > Random Question: > - is device polling really the answer? I am missing something in the bge > driver that I've overlooked? > - what tunables directly effect processing high volumes of packets. >
<snip> After some more coffee, and source code reading, I've now learned that having device polling enabled forces netisr to limit the number of threads it creates to 1. This kinda defeats the purpose of enabling device polling. This makes me believe that device polling isn't going to be a great solution afterall. A snippet from dmesg: <snip> bge0: <Compaq NC7781 Gigabit Server Adapter, ASIC rev. 0x001002> mem 0xf7ef0000-0xf7efffff irq 30 at device 2.0 on pci1 brgphy0: <BCM5703 10/100/1000baseTX PHY> PHY 1 on miibus0 bge1: <Compaq NC7781 Gigabit Server Adapter, ASIC rev. 0x001002> mem 0xf7ff0000-0xf7ffffff irq 29 at device 2.0 on pci4 brgphy1: <BCM5703 10/100/1000baseTX PHY> PHY 1 on miibus1 <snip> Any help/advice is appreciated, and sorry for following up to myself with this information. ~Paul ________________________________ This message may contain confidential or privileged information. If you are not the intended recipient, please advise us immediately and delete this message. See http://www.datapipe.com/about-us-legal-email-disclaimer.htm for further information on confidentiality and the risks of non-secure electronic communication. If you cannot access these links, please notify us by reply message and we will send the contents to you. _______________________________________________ freebsd-net@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-net To unsubscribe, send any mail to "freebsd-net-unsubscr...@freebsd.org"
