Nickolas, I TRIED THAT .. first with vga in the device sections, then vesa, via, savage, sis and finally back to vga .. ONLY vga DID NOT produce an immediate EXIT -- stating NO SCREEN FOUND ... so NOW WHAT ??? # The Driver line must be present. When using run-time loadable driver # modules, this line instructs the server to load the specified driver # module. Even when not using loadable driver modules, this line # indicates which driver should interpret the information in this section.
#XXXX vga XX vesa via savage sis Driver "vga" On 6/14/05, Nikolas Britton <[EMAIL PROTECTED]> wrote: > > On 6/14/05, Ev Batey WA6CRE <[EMAIL PROTECTED]> wrote: > > > > > [snipped (every thing)] > > > > > > The KM400 uses the VIA S3 UniChrome. Try changing the driver section > in the xorg.conf file to the via driver. "man via" for more info. > Starting with a fresh xorg.conf file might be good idea too, "Xorg > -configure". As far as the KM266 thingy, both FreeBSD and Xorg say > it's a KM400 Chipset*.... see the bottom of my post. *sorry I allmost > missed that, the system says it has a "CLE266", not a KM266. The > CLE266 uses the UniChrome: > > "(II) VIA(0): VESA VBE OEM: VIA CLE266" > > ------------------------------------ > "MSI KM3M-V (VIA KM266, registers as KM400)" > "Have an MSI KM3M-V KM266 (supposedly an S3 Savage like chip)." > ------------------------------------- > ABI class: X.Org <http://X.Org> <http://x.org/> Video Driver, version 0.7 > (II) VIA(0): VESA BIOS detected > (II) VIA(0): VESA VBE Version 3.0 > (II) VIA(0): VESA VBE Total Mem: 65536 kB > (II) VIA(0): VESA VBE OEM: VIA CLE266 > > (II) VIA(0): VESA VBE OEM Software Rev: 0.0 > (--) VIA(0): Chipset: "KM400" > (--) VIA(0): Chipset Rev.: 132 > (II) VIA(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is > 0x0000 > (--) VIA(0): mapping MMIO @ 0xec000000 with size 0x9000 > (==) VIA(0): Write-combining range (0xec000000,0x9000) was already clear > (--) VIA(0): mapping BitBlt MMIO @ 0xec200000 with size 0x10000 > (==) VIA(0): Write-combining range (0xec200000,0x10000) was already clear > (II) VIA(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is > 0x0000 > > (==) VIA(0): Using gamma correction (1.0, 1.0, 1.0) > (--) VIA(0): videoram = 65536k > ------------------------------------- > agp0: <VIA 8235/8237 (Apollo KM400/KM400A) host to PCI bridge> mem > 0xe0000000-0xe7ffffff at device 0.0 on pci0 > agp0: Reserved 0x8000000 bytes for rid 0x10 type 3 at 0xe0000000 > agp0: allocating GATT for aperture of size 256M > ------------------------------------- > http://www.via.com.tw/en/products/chipsets/legacy/km266/ > http://www.via.com.tw/en/products/chipsets/k7-series/km400/ > > KM266 = S3 Graphics ProSavage8 > KM400 = UniChrome™ 2D/3D Graphics with motion compensation > -- Ev Batey -- WA6CRE -- [EMAIL PROTECTED] 805 340-6471 http://www.cotdazr.org
_______________________________________________ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to "[EMAIL PROTECTED]"
