Thanks for the advice but again, I am very new to all this. Can you tell me how to check if miibus is enabled and how to enable it if it is not?
Thanks in advance, Tom Connolly -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of Kevin D. Kinsey, DaleCo, S.P. Sent: Monday, December 09, 2002 2:07 PM To: Thomas Connolly; 'Brian'; [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Subject: Re: Ethernet card problem dc driver uses the miibus code, make sure you have that enabled on your kernel. There is nothing needed in "sysinstall", a device probe ought to catch it IF the miibus is enabled in your kernel config..... Sorry, I'm late on this discussion, if I've missed important points, please forgive....I just hadn't seen this point mentioned. Kevin Kinsey DaleCo, S.P. ----- Original Message ----- From: "Thomas Connolly" <[EMAIL PROTECTED]> To: "'Brian'" <[EMAIL PROTECTED]>; <[EMAIL PROTECTED]> Cc: <[EMAIL PROTECTED]> Sent: Monday, December 09, 2002 11:50 AM Subject: RE: Ethernet card problem Yes, that is what I tried to do but my interface doesn't come up in the list, only plip, and com 1 come up, not dc0. Thanks, Thomas Connolly -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of Brian Sent: Monday, December 09, 2002 10:45 AM To: Thomas Connolly; [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Subject: Re: Ethernet card problem isnt is /stand/sysinstall, post install config, network, pick yer interface, answer yes to the dhcp popup, thats it? BTW, if it asks you if you want to activate now, that typically will not get you the new parameters on the interface, youll need to either ifconfig it down and then up, or reboot as a quik& dirty way. Bri ----- Original Message ----- From: "Thomas Connolly" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Cc: <[EMAIL PROTECTED]> Sent: Monday, December 09, 2002 9:36 AM Subject: RE: Ethernet card problem > Thanks again for the help. Can you tell me how to set my interface up > manually so that it will use DHCP for the ip and netmask, gateway, etc.? > > Thanks, > > Tom Connolly > > -----Original Message----- > From: D J Hawkey Jr [mailto:[EMAIL PROTECTED]] > Sent: Monday, December 09, 2002 10:25 AM > To: Thomas Connolly > Subject: Re: Ethernet card problem > > On Dec 09, at 10:07 AM, Thomas Connolly wrote: > > > > Thanks very much for the quick reply. > > I would agree with that. The model is a Kingston KNE100TX and it says > that > > the driver is a dc(4). Which Ethernet selection and I supposed to pick > for > > that on Sysinstall? > > dc0, I would imagine. > > > Is there a way to reconfigure it after installation. > > Oh, yes. Go on through the installation. Afterward, edit /etc/rc.conf to > reflect reality. You'll have lines like these to change: > hostname="sheol.localdomain" > ifconfig_ed0="inet 192.168.16.2 netmask 255.255.255.0" > What you'll change is the hostname (if need be), and ifconfig_ed0 to > ifconfig_dc0. IIRC, that's all it takes. > > > I > > apologize for the ignorance but I am very new to all this. I basically > just > > went step-by-step through the FreeBSD manual on installation. There was > no > > option that said dc(4). > > I don't remember how to specify the interface within sysinstall(8), but I'm > sure you can (make sure you've resolved conflicting interrupts first). > I usually set up the network manually, after sysinstall(8), just to stay in > practice! > > > Thanks again, > > Thomas P. Connolly > > Senior Development Engineer > > Colorado Engineering Experiment Station Inc. > > Phone: (970) 897-2711 > > Fax: (970) 897-2710 > > Email: [EMAIL PROTECTED] > > Need a telecommuting UNIX SysAdmin in Minnesota? > Dave > > -- > ______________________ ______________________ > \__________________ \ D. J. HAWKEY JR. / __________________/ > \________________/\ [EMAIL PROTECTED] /\________________/ > http://www.visi.com/~hawkeyd/ > > > To Unsubscribe: send mail to [EMAIL PROTECTED] > with "unsubscribe freebsd-questions" in the body of the message > To Unsubscribe: send mail to [EMAIL PROTECTED] with "unsubscribe freebsd-questions" in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with "unsubscribe freebsd-questions" in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with "unsubscribe freebsd-questions" in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with "unsubscribe freebsd-questions" in the body of the message