hi sirs,
yesterday, i launched etherape to em0 nic, etherape -i em0, and got
that message. before that there was no error.
worse is that root can not launch any x applications except xterm, it
get the same error messages.
here is uname of my r51 thinkpad
%uname -a
FreeBSD siting.oaep.go.th 6.1-RELEASE FreeBSD 6.1-RELEASE #0: Sun May 14
18:00:24 ICT 2006
[EMAIL PROTECTED]:/usr/obj/usr/src/sys/SITING i386
%
and ifconfig
%ifconfig -a
fwe0: flags=108902<BROADCAST,PROMISC,SIMPLEX,MULTICAST,NEEDSGIANT> mtu 1500
options=8<VLAN_MTU>
inet6 fe80::6:1bff:fe02:b8fb%fwe0 prefixlen 64 scopeid 0x1
ether 02:06:1b:02:b8:fb
ch 1 dma -1
em0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=b<RXCSUM,TXCSUM,VLAN_MTU>
inet6 fe80::211:25ff:feb2:23be%em0 prefixlen 64 scopeid 0x2
inet 10.3.2.25 netmask 0xffffff00 broadcast 10.3.2.255
ether 00:11:25:b2:23:be
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet6 fe80::20e:9bff:fea3:d91a%ath0 prefixlen 64 scopeid 0x3
ether 00:0e:9b:a3:d9:1a
media: IEEE 802.11 Wireless Ethernet autoselect (OFDM/36Mbps)
status: associated
ssid Reactor channel 6 bssid 00:15:e9:40:17:98
authmode OPEN privacy OFF txpowmax 34 protmode CTS burst bintval 100
plip0: flags=108810<POINTOPOINT,SIMPLEX,MULTICAST,NEEDSGIANT> mtu 1500
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5
inet 127.0.0.1 netmask 0xff000000
%
and below is dmesg
%dmesg
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.1-RELEASE #0: Sun May 14 18:00:24 ICT 2006
[EMAIL PROTECTED]:/usr/obj/usr/src/sys/SITING
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) M processor 1.60GHz (1594.83-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6d6 Stepping = 6
Features=0xafe9f9bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,PBE>
Features2=0x180<EST,TM2>
real memory = 1064173568 (1014 MB)
avail memory = 1032421376 (984 MB)
kbd1 at kbdmux0
ath_hal: 0.9.16.16 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
acpi0: <IBM TP-1V> on motherboard
acpi_ec0: <Embedded Controller: GPE 0x1c, ECDT> port 0x62,0x66 on acpi0
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_perf0: <ACPI CPU Frequency Control> on cpu0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <base peripheral> at device 0.1 (no driver attached)
pci0: <base peripheral> at device 0.3 (no driver attached)
agp0: <Intel 82855GME (855GME GMCH) SVGA controller> port 0x1800-0x1807
mem 0xe0000000-0xe7ffffff,0xd0000000-0xd007ffff irq 11 at device 2.0 on pci0
agp0: detected 8060k stolen memory
agp0: aperture size is 128M
pci0: <display> at device 2.1 (no driver attached)
uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0x1820-0x183f
irq 11 at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0x1840-0x185f
irq 11 at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0x1860-0x187f
irq 11 at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0: <Intel 82801DB/L/M (ICH4) USB 2.0 controller> mem
0xd0100000-0xd01003ff irq 11 at device 29.7 on pci0
ehci0: [GIANT-LOCKED]
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <Intel 82801DB/L/M (ICH4) USB 2.0 controller> on ehci0
usb3: USB revision 2.0
uhub3: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
umass0: vendor 0x05e3 USB TO IDE, rev 2.00/0.33, addr 2
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib1
cbb0: <TI4510 PCI-CardBus Bridge> mem 0xb0000000-0xb0000fff irq 11 at
device 0.0 on pci2
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
fwohci0: <1394 Open Host Controller Interface> mem
0xb1000000-0xb10007ff,0xd0210000-0xd0213fff irq 11 at device 0.1 on pci2
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:06:1b:03:24:02:b8:fb
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:06:1b:02:b8:fb
fwe0: Ethernet address: 02:06:1b:02:b8:fb
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
em0: <Intel(R) PRO/1000 Network Connection Version - 3.2.18> port
0x7000-0x703f mem 0xd0220000-0xd023ffff irq 11 at device 1.0 on pci2
em0: Ethernet address: 00:11:25:b2:23:be
ath0: <Atheros 5212> mem 0xd0200000-0xd020ffff irq 11 at device 2.0 on pci2
ath0: Ethernet address: 00:0e:9b:a3:d9:1a
ath0: mac 5.9 phy 4.3 radio 4.6
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH4 UDMA100 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1810-0x181f at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pcm0: <Intel ICH4 (82801DB)> port 0x1c00-0x1cff,0x18c0-0x18ff mem
0xd0100c00-0xd0100dff,0xd0100800-0xd01008ff irq 11 at device 31.5 on pci0
pcm0: <Analog Devices AD1981B AC97 Codec>
pci0: <simple comms, generic modem> at device 31.6 (no driver attached)
acpi_tz0: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model Generic PS/2 mouse, device ID 0
fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2
on acpi0
fdc0: [FAST]
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on
acpi0
sio0: type 8250 or not responding
ppc0: <Standard parallel printer port> port 0x3bc-0x3be irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
battery0: <ACPI Control Method Battery> on acpi0
acpi_acad0: <AC Adapter> on acpi0
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem
0xcd000-0xcdfff,0xce000-0xcefff,0xdc000-0xdffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 1594829759 Hz quality 800
Timecounters tick every 1.000 msec
ipfw2 (+ipv6) initialized, divert loadable, rule-based forwarding
disabled, default to accept, logging unlimited
ad0: 76319MB <IC25N080ATMR04 0 MO4OADEA> at ata0-master UDMA100
acd0: CDRW <HL-DT-STCD-RW/DVD DRIVE GCC-4241N/1.04> at ata1-master UDMA33
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <HTS42404 0M9AT00 0811> Fixed Direct Access SCSI-0 device
da0: 40.000MB/s transfers
da0: 38154MB (78140160 512 byte sectors: 255H 63S/T 4864C)
Trying to mount root from ufs:/dev/da0s2a
drmsub1: <Intel i852GM/i855GM GMCH> mem
0xe8000000-0xefffffff,0xd0080000-0xd00fffff at device 2.1 on pci0
info: [drm] AGP at 0xe0000000 128MB
info: [drm] Initialized i915 1.2.0 20041217
ath0: link state changed to DOWN
ath0: link state changed to UP
ath0: link state changed to DOWN
ath0: link state changed to UP
ath0: link state changed to DOWN
ath0: link state changed to UP
ath0: link state changed to DOWN
ath0: link state changed to UP
ath0: link state changed to DOWN
ath0: link state changed to UP
ath0: link state changed to DOWN
ath0: link state changed to UP
ath0: link state changed to DOWN
ath0: link state changed to UP
ath0: link state changed to DOWN
ath0: link state changed to UP
ath0: link state changed to DOWN
ath0: link state changed to UP
ath0: link state changed to DOWN
ath0: link state changed to UP
ath0: link state changed to DOWN
ath0: link state changed to UP
ath0: link state changed to DOWN
ath0: link state changed to UP
ath0: link state changed to DOWN
ath0: link state changed to UP
ath0: link state changed to DOWN
ath0: link state changed to UP
ath0: link state changed to DOWN
ath0: link state changed to UP
ath0: link state changed to DOWN
ath0: link state changed to UP
ath0: link state changed to DOWN
ath0: link state changed to UP
ath0: link state changed to DOWN
ath0: link state changed to UP
%
what i did yesterday was to assign ip number to fwe0 nic via sysinstall
and unassign it later .
please help me.
thanks in advance for any helps and hints.
with best regards,
psr
PS search from questions-mailing list does not give any clue to solve my
case./psr
_______________________________________________
freebsd-questions@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
