Hello Lane!
I'm a frequent reader to /usr/src/UPDATING
But whenever I need to update or upgrade only, since years!
Also I knew very well whats KERNCONF! i just wanted to know and make sure
of the duo core
options, and i searched the NOTES file, didnot find anything about it.
Thank you for your "short" problematic answer :)
by the way, After recompiling the kernel and From my dmesg
--------------------
ACPI APIC Table: <INTEL D11020M >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
ioapic0: Changing APIC ID to 4
SMP: AP CPU #1 Launched!
---------------------
But I still have few dmesg errors, these are the lines,
acpi0: <INTEL D11020M> on motherboard
acpi0: Overriding SCI Interrupt from IRQ 9 to IRQ 21
acpi0: Power Button (fixed)
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
unknown: I/O range not supported
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_perf0: <ACPI CPU Frequency Control> on cpu0
acpi_perf0: failed in PERF_STATUS attach
device_attach: acpi_perf0 attach returned 6
acpi_perf0: <ACPI CPU Frequency Control> on cpu0
acpi_perf0: failed in PERF_STATUS attach
device_attach: acpi_perf0 attach returned 6
acpi_throttle0: <ACPI CPU Throttling> on cpu0
cpu1: <ACPI CPU> on acpi0
acpi_perf1: <ACPI CPU Frequency Control> on cpu1
acpi_perf1: failed in PERF_STATUS attach
device_attach: acpi_perf1 attach returned 6
acpi_perf1: <ACPI CPU Frequency Control> on cpu1
acpi_perf1: failed in PERF_STATUS attach
device_attach: acpi_perf1 attach returned 6
acpi_throttle1: <ACPI CPU Throttling> on cpu1
acpi_throttle1: failed to attach P_CNT
device_attach: acpi_throttle1 attach returned 6
acpi_button0: <Power Button> on acpi0
and
usb2: waiting for BIOS to give up control
usb2: timed out waiting for BIOS
usb2: EHCI version 1.0
usb2: companion controllers, 4 ports each: usb0 usb1
usb2: <ATI SB400 USB 2.0 controller> on ehci0
usb2: USB revision 2.0
Any easy problematic ideas? :)
Thank you
---Marwan
First read /usr/src/UPDATING.
Really.
No, really. I mean read it :)
And, since no one expects you to really, really read it, I'll give you some
shortcuts.
First, look for the word KERNCONF in /usr/src/UPDATING
Read all of the language around every occurence of that word (KERNCONF).
Then, when you are ready, do this:
make buildkernel KERNCONF=SMP
make installkernel KERNCONF=SMP
Then reboot.
Note here that I'm giving you the shortest possible route, which may be
problematic for you. You really must become familiar with
/usr/src/UPDATING.
Anyway, after the reboot, you should type:
cat /var/log/messages | grep -i launch
if you see the terms "CPU1 Launched!" then you've got yourself an SMP
kernel.
Good Luck!
lane
_________________________________________________________________
FREE pop-up blocking with the new MSN Toolbar - get it now!
http://toolbar.msn.click-url.com/go/onm00200415ave/direct/01/
_______________________________________________
freebsd-questions@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
