N, 19 apr 2007 kirjutas "М. Павел" <[EMAIL PROTECTED]>:
Good Day.
I▓ve got a problem:
Server:
- Motherboard Intel SE7320ep2 with integrated, simple, but fully
hardware raid controller.
- Two HDDs Seagate 200 gb combined into raid 1 (mirror).
The HDD has 3 sections:
3 √ not formated
1 √ win2003 server
2 √ keeps logic drives for windows
(there number means diskpart, not a order)
While booting from installation CD (on device probing stage) i've
got following message:
...
atapci0: <Intel 6300ESB UDMA100 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 31.1 on
pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
atapci1: <Intel 6300ESB SATA150 controller> port
0xce80-0xce87,0xce00-0xce03,0xcd80-0xcd87,0xcd00-0xcd03,0xcc80-0xcc8f irq 18
at device 31.2 on pci0
ata2: <ATA channel 0> on atapci1
ata3: <ATA channel 1> on atapci1
...
ad4: 188348MB <Seagate ST3300831AS 3.03> at ata2-master SATA150
ad6: 188348MB <Seagate ST3300831AS 3.03> at ata3-master SATA150
ar0: 188348MB <LSILogic v3 MegaRAID RAID1> status: READY
ar0: disk0 READY (master) using ad4 at ata2-master
ar0: disk1 READY (mirror) using ad6 at ata3-master
...
During the installation of freebsd6.2 there are 3 variants where
freebsd can be established: ad4,ad6,ar0.
I install the program to the drive ar0, make a slice on it and
install the Boot Manager in MBR.
After the installation before rebooting the system I make sure that
everything I need was copied.
Also i checked what says atacontrol
atacontrol status ar0
ar0: ATA RAID 1 subdisks: ad4 ad6 status:READY
and pciconf:
pciconf -lv
...
[EMAIL PROTECTED]:31:1: class=0x01018a card=0x34508086
chip=0x25a28086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '6300ESB IDE Controller'
class = mass storage
subclass = ATA
[EMAIL PROTECTED]:31:2: class=0x01048f card=0x34518086
chip=0x25b08086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '6300ESB Serial ATA Controller (RAID mode)'
class = mass storage
subclass = RAID
...
This means that the drive is visible and freebsd defines it to be normal (?)
Then Reboot.
F1 - Successfully loads windows
F3 - after BTX Loader I receive the following message: "can▓t load
kerner. Reason: not found"
lsdev says
lsdev
disk devices:
disk0: BIOS drive A:
disk1: BIOS drive C:
show currdev
disk1s3a
However while i loading from installation CD
lsdev
disk devices:
disk0: BIOS drive A:
disk1: BIOS drive C:
disk1s3a: FFS
disk1s3b: swap
disk1s3d: FFS
disk1s3e: FFS
disk1s3f: FFS
After that I reboot the computer and raid controller reports that
the RAID is in DEGRADED state and drives need synchronization.
_______________________________________________
freebsd-questions@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
--
Toomas Aas
_______________________________________________
freebsd-questions@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to "[EMAIL PROTECTED]"