Hi, found this old P2B-D board with two 1GHz CPUs and don't want to throw it away ;-)
Has anyone got it running with ACPI and without the interrupt storm on irq20? Judging from old mailing list messages it was blacklisted in 5.3 so ACPI got disabled but since it doesn't in 6.4-STABLE the issues were possibly fixed and I am simply too stupid... Another thing is the SMB. I have lots of P2B and P2B-L boards where the SMB is running fine (used by healthd). On this P2B-D it doesn't even attach using the usual device smbus device intpm device smb lines in the kernel. This is the dmesg (without ACPI), nothing special to see. When enabling ACPI we see an error about an interrupt storm on irq20 constantly... Copyright (c) 1992-2008 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 6.4-STABLE #5: Wed May 20 11:58:13 CEST 2009 r...@server.ofw.tld:/src/obj-6/src/src-6/sys/cvsfix Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel Pentium III (1002.28-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x686 Stepping = 6 Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> real memory = 536858624 (511 MB) avail memory = 520503296 (496 MB) MPTable: <OEM00000 PROD00000000> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 1 cpu1 (AP): APIC ID: 0 ioapic0: Assuming intbase of 0 ioapic0 <Version 1.1> irqs 0-23 on motherboard cpu0 on motherboard cpu1 on motherboard pcib0: <MPTable Host-PCI bridge> pcibus 0 on motherboard pci0: <PCI bus> on pcib0 eccmon0: RAM ECC Monitor v0.01 on 8086:7190 eccmon0: Chipset (i440BX/ZX) ECC capability: ECC with hardware scrubber eccmon0: Active mode: ECC with hardware scrubber eccmon0: Bank Size Type ILV ECC eccmon0: 0 128M SDR N Y eccmon0: 1 128M SDR N Y eccmon0: 2 128M SDR N Y eccmon0: 3 128M SDR N Y eccmon0: Total RAM detected: 512M eccmon0: attached pcib1: <MPTable PCI-PCI bridge> at device 1.0 on pci0 pci1: <PCI bus> on pcib1 pci1: <display, VGA> at device 0.0 (no driver attached) isab0: <PCI-ISA bridge> at device 4.0 on pci0 isa0: <ISA bus> on isab0 pci0: <mass storage, ATA> at device 4.1 (no driver attached) pci0: <serial bus, USB> at device 4.2 (no driver attached) piix0: <PIIX Timecounter> port 0xe800-0xe80f at device 4.3 on pci0 Timecounter "PIIX" frequency 3579545 Hz quality 0 ahc0: <Adaptec 29160 Ultra160 SCSI adapter> port 0xd000-0xd0ff mem 0xd6800000-0xd6800fff irq 18 at device 10.0 on pci0 ahc0: Bugs (0x0040): SCBCHAN_UPLOAD ahc0: [GIANT-LOCKED] aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs em0: <Intel(R) PRO/1000 Network Connection Version - 6.7.3> port 0xb800-0xb83f mem 0xd6000000-0xd601ffff irq 17 at device 11.0 on pci0 em0: Ethernet address: 00:07:e9:14:56:a6 orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 atkbd0: [GIANT-LOCKED] fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: [FAST] fd0: <1440-KB 3.5" drive> on fdc0 drive 0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <9 virtual consoles, flags=0x300> vga0: <Generic ISA VGA> at port 0x3b0-0x3df iomem 0xa0000-0xbffff on isa0 uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 4 on isa0 uart1: <16550 or compatible> at port 0x2f8-0x2ff irq 3 on isa0 unknown: <PNP0700> can't assign resources (port) unknown: <PNP0c01> can't assign resources (memory) unknown: <PNP0303> can't assign resources (port) unknown: <PNP0c02> can't assign resources (port) Timecounters tick every 10.000 msec da0 at ahc0 bus 0 target 0 lun 0 da0: <SEAGATE ST39175LW 0001> Fixed Direct Access SCSI-2 device da0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled da0: 8683MB (17783240 512 byte sectors: 255H 63S/T 1106C) da1 at ahc0 bus 0 target 1 lun 0 da1: <QUANTUM XP39100S LYK8> Fixed Direct Access SCSI-2 device da1: 20.000MB/s transfers (20.000MHz, offset 31), Tagged Queueing Enabled da1: 8682MB (17781520 512 byte sectors: 255H 63S/T 1106C) da2 at ahc0 bus 0 target 2 lun 0 da2: <SEAGATE ST318404LW 3251> Fixed Direct Access SCSI-3 device da2: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled da2: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C) da3 at ahc0 bus 0 target 3 lun 0 da3: <SEAGATE ST318404LW 3251> Fixed Direct Access SCSI-3 device da3: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled da3: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C) SMP: AP CPU #1 Launched! cd0 at ahc0 bus 0 target 6 lun 0 cd0: <TOSHIBA CD-ROM XM-6201TA 1400> Removable CD-ROM SCSI-2 device cd0: 10.000MB/s transfers (10.000MHz, offset 16) cd0: Attempt to query device size failed: NOT READY, Medium not present Trying to mount root from ufs:/dev/da0s1a Thanks, -Andre _______________________________________________ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to "freebsd-questions-unsubscr...@freebsd.org"