On 23-Jul-12 16:07, Erich Dollansky wrote:
Hi,
On Monday 23 July 2012 16:46:04 Manish Jain wrote:
On 21-Jul-12 19:06, Matthias Apitz wrote:
El día Saturday, July 21, 2012 a las 06:01:11PM +0530, Manish Jain escribió:
I am still stuck because I can't know the syntax to run usbdump. usbdump
man usbdump
usbconfig gives you the device numbers.
Can someone please send me the sources for this port (sysutils/usbutils)
All you need at this stage is in the base.
(please remove freebsd-questions@freebsd.org from addresses if sending),
as I cannot currently connect my FreeBSD box to the internet.
If we do no other people will be able to help you.
BTW, cuaU0[.*] are always there on my system, whether my EC1561 stick is
It might be your UPS.
Erich
Hi,
You are right. cuaU0.0 is my UPS. I checked the vendor id and the
product id : they are 12d1 (huawei) and 140b (the USB stick I have).
This is confirmed with usbconfig and what Windows Device Manager shows.
However, running 'usbdump -d 12d1:140b' produces no output. In fact
there is no entry 12d1:140b under /etc/usb_modeswitch.d/. Do I need to
reinstall usb_modeswitch ?
usbconfig dumps the following information for a1:u2 :
ugen1.2: <HUAWEI Mobile HUAWEI TECHNOLOGIES> at usbus1, cfg=0 md=HOST
spd=FULL (12Mbps) pwr=ON
bLength = 0x0012
bDescriptorType = 0x0001
bcdUSB = 0x0110
bDeviceClass = 0x0000
bDeviceSubClass = 0x0000
bDeviceProtocol = 0x0000
bMaxPacketSize0 = 0x0040
idVendor = 0x12d1
idProduct = 0x140b
bcdDevice = 0x0000
iManufacturer = 0x0001 <HUAWEI TECHNOLOGIES>
iProduct = 0x0002 <HUAWEI Mobile>
iSerialNumber = 0x0004 <>
bNumConfigurations = 0x0001
I tried setting the device in ppp.conf to cuaU0, cuaU0.1, cuaU0.2 and
ugen1.2, but had no success in getting the modem to speak to the internet.
Am pasting a few lines from ppp.log :
Jul 23 22:25:15 bourne ppp[1207]: Phase: Using interface: tun0
Jul 23 22:25:15 bourne ppp[1207]: Phase: deflink: Created in closed state
Jul 23 22:25:15 bourne ppp[1207]: tun0: Command: default: set device
/dev/cuaU0
Jul 23 22:25:15 bourne ppp[1207]: tun0: Command: default: set speed 115200
Jul 23 22:25:15 bourne ppp[1207]: tun0: Command: default: set dial ABORT
BUSY ABORT NO\sCARRIER TIMEOUT 5 "" AT OK-AT-OK AT&FE0V1X1&D2&C1S0=0 OK
\dATDT\T TIMEOUT 40 CONNECT
Jul 23 22:25:15 bourne ppp[1207]: tun0: Command: default: set timeout 180
Jul 23 22:25:15 bourne ppp[1207]: tun0: Command: default: enable dns
Jul 23 22:25:15 bourne ppp[1207]: tun0: Command: huawei: set phone #777
Jul 23 22:25:15 bourne ppp[1207]: tun0: Command: huawei: set device
/dev/cuaU0
Jul 23 22:25:15 bourne ppp[1207]: tun0: Command: huawei: set login
Jul 23 22:25:15 bourne ppp[1207]: tun0: Command: huawei: set authname
inter...@internet.mtsindia.in
Jul 23 22:25:15 bourne ppp[1207]: tun0: Command: huawei: set authkey
********
Jul 23 22:25:15 bourne ppp[1207]: tun0: Command: huawei: set timeout 0
Jul 23 22:25:15 bourne ppp[1207]: tun0: Command: huawei: disable ipv6cp
Jul 23 22:25:15 bourne ppp[1207]: tun0: Command: huawei: set ifaddr
10.0.0.1/0 10.0.0.2/0 255.255.255.0 0.0.0.0
Jul 23 22:25:15 bourne ppp[1207]: tun0: Command: huawei: add default HISADDR
Jul 23 22:25:15 bourne ppp[1207]: tun0: Command: huawei: set dial AT+CRM=1
Jul 23 22:25:15 bourne ppp[1207]: tun0: Command: huawei: accept CHAP
Jul 23 22:25:15 bourne ppp[1224]: tun0: Phase: PPP Started (auto mode).
Jul 23 22:25:15 bourne ppp[1224]: tun0: Phase: bundle: Establish
Jul 23 22:25:15 bourne ppp[1224]: tun0: Phase: deflink: closed -> opening
Jul 23 22:25:15 bourne ppp[1224]: tun0: Warning: deflink: /dev/cuaU0:
Bad file descriptor
Jul 23 22:25:15 bourne ppp[1224]: tun0: Chat: Failed to open device
(attempt 1 of 1)
Jul 23 22:25:15 bourne ppp[1224]: tun0: Phase: deflink: opening -> closed
Jul 23 22:25:15 bourne ppp[1224]: tun0: Phase: bundle: Dead
Jul 23 22:36:19 bourne ppp[1207]: Phase: Using interface: tun0
Jul 23 22:36:19 bourne ppp[1207]: Phase: deflink: Created in closed state
Jul 23 22:36:19 bourne ppp[1207]: tun0: Command: default: set device
/dev/modem
Jul 23 22:36:19 bourne ppp[1207]: tun0: Command: default: set speed 115200
Jul 23 22:36:19 bourne ppp[1207]: tun0: Command: default: set dial ABORT
BUSY ABORT NO\sCARRIER TIMEOUT 5 "" AT OK-AT-OK AT&FE0V1X1&D2&C1S0=0 OK
\dATDT\T TIMEOUT 40 CONNECT
Jul 23 22:36:19 bourne ppp[1207]: tun0: Command: default: set timeout 180
Jul 23 22:36:19 bourne ppp[1207]: tun0: Command: default: enable dns
Jul 23 22:36:19 bourne ppp[1207]: tun0: Command: huawei: set phone #777
Jul 23 22:36:19 bourne ppp[1207]: tun0: Command: huawei: set device
/dev/modem
Jul 23 22:36:19 bourne ppp[1207]: tun0: Command: huawei: set login
Jul 23 22:36:19 bourne ppp[1207]: tun0: Command: huawei: set authname
inter...@internet.mtsindia.in
Jul 23 22:36:19 bourne ppp[1207]: tun0: Command: huawei: set authkey
********
Jul 23 22:36:19 bourne ppp[1207]: tun0: Command: huawei: set timeout 0
Jul 23 22:36:19 bourne ppp[1207]: tun0: Command: huawei: disable ipv6cp
Jul 23 22:36:19 bourne ppp[1207]: tun0: Command: huawei: set ifaddr
10.0.0.1/0 10.0.0.2/0 255.255.255.0 0.0.0.0
Jul 23 22:36:19 bourne ppp[1207]: tun0: Command: huawei: add default HISADDR
Jul 23 22:36:19 bourne ppp[1207]: tun0: Command: huawei: set dial AT+CRM=1
Jul 23 22:36:19 bourne ppp[1207]: tun0: Command: huawei: accept CHAP
Jul 23 22:36:19 bourne ppp[1217]: tun0: Phase: PPP Started (auto mode).
Jul 23 22:36:19 bourne ppp[1217]: tun0: Phase: bundle: Establish
Jul 23 22:36:19 bourne ppp[1217]: tun0: Phase: deflink: closed -> opening
Jul 23 22:36:19 bourne ppp[1217]: tun0: Phase: deflink: Connected!
Jul 23 22:36:19 bourne ppp[1217]: tun0: Phase: deflink: opening -> dial
Jul 23 22:36:19 bourne ppp[1217]: tun0: Chat: Phone: #777
Jul 23 22:36:19 bourne ppp[1217]: tun0: Chat: deflink: Dial attempt 1 of 1
Jul 23 22:36:19 bourne ppp[1217]: tun0: Chat: Expect(30): AT+CRM=1
Jul 23 22:36:49 bourne ppp[1217]: tun0: Chat: Expect timeout
Jul 23 22:36:49 bourne ppp[1217]: tun0: Warning: Chat script failed
Jul 23 22:36:49 bourne ppp[1217]: tun0: Phase: deflink: dial -> hangup
Jul 23 22:36:49 bourne ppp[1217]: tun0: Phase: deflink: Disconnected!
Jul 23 22:36:49 bourne ppp[1217]: tun0: Phase: deflink: Connect time: 30
secs: 0 octets in, 0 octets out
Jul 23 22:36:49 bourne ppp[1217]: tun0: Phase: deflink: 0 packets in, 0
packets out
Jul 23 22:36:49 bourne ppp[1217]: tun0: Phase: total 0 bytes/sec, peak
0 bytes/sec on Mon Jul 23 22:36:19 2012
Jul 23 22:36:49 bourne ppp[1217]: tun0: Phase: deflink: hangup -> closed
Jul 23 22:36:49 bourne ppp[1217]: tun0: Phase: bundle: Dead
Jul 23 22:36:50 bourne ppp[1217]: tun0: Phase: bundle: Establish
Jul 23 22:36:50 bourne ppp[1217]: tun0: Phase: deflink: closed -> opening
Jul 23 22:36:50 bourne ppp[1217]: tun0: Phase: deflink: Connected!
Jul 23 22:36:50 bourne ppp[1217]: tun0: Phase: deflink: opening -> dial
Jul 23 22:36:50 bourne ppp[1217]: tun0: Chat: Phone: #777
Jul 23 22:36:50 bourne ppp[1217]: tun0: Chat: deflink: Dial attempt 1 of 1
Jul 23 22:36:50 bourne ppp[1217]: tun0: Chat: Expect(30): AT+CRM=1
Jul 23 22:37:20 bourne ppp[1217]: tun0: Chat: Expect timeout
Jul 23 22:37:20 bourne ppp[1217]: tun0: Warning: Chat script failed
Jul 23 22:37:20 bourne ppp[1217]: tun0: Phase: deflink: dial -> hangup
Jul 23 22:37:20 bourne ppp[1217]: tun0: Phase: deflink: Disconnected!
Jul 23 22:37:20 bourne ppp[1217]: tun0: Phase: deflink: Connect time: 30
secs: 0 octets in, 0 octets out
Jul 23 22:37:20 bourne ppp[1217]: tun0: Phase: deflink: 0 packets in, 0
packets out
Jul 23 22:37:20 bourne ppp[1217]: tun0: Phase: total 0 bytes/sec, peak
0 bytes/sec on Mon Jul 23 22:36:50 2012
Jul 23 22:37:20 bourne ppp[1217]: tun0: Phase: deflink: hangup -> closed
Jul 23 22:37:20 bourne ppp[1217]: tun0: Phase: bundle: Dead
And a few lines from Windows' ppp log (Windows connects smoothly) :
07-23-2012 23:56:23.203 - Modem type: HUAWEI Mobile Connect - Modem
07-23-2012 23:56:23.203 - Modem inf path: oem10.inf
07-23-2012 23:56:23.203 - Modem inf section: Modem1
07-23-2012 23:56:23.203 - Matching hardware ID: usb\vid_12d1&pid_140b&mi_00
07-23-2012 23:56:23.234 - 460800,8,N,1, ctsfl=0, rtsctl=1
07-23-2012 23:56:23.234 - Initializing modem.
07-23-2012 23:56:23.250 - Send: AT<cr>
07-23-2012 23:56:23.250 - Recv: <cr><lf>OK<cr><lf>
07-23-2012 23:56:23.250 - Interpreted response: OK
07-23-2012 23:56:23.265 - Send: AT&FE0V1X1&D2&C1S0=0<cr>
07-23-2012 23:56:23.296 - Recv: <cr><lf>OK<cr><lf>
07-23-2012 23:56:23.296 - Interpreted response: OK
07-23-2012 23:56:23.296 - Send: AT<cr>
07-23-2012 23:56:23.296 - Recv: <cr><lf>OK<cr><lf>
07-23-2012 23:56:23.296 - Interpreted response: OK
07-23-2012 23:56:23.296 - Waiting for a call.
07-23-2012 23:56:23.312 - Send: ATS0=0<cr>
07-23-2012 23:56:23.312 - Recv: <cr><lf>OK<cr><lf>
07-23-2012 23:56:23.312 - Interpreted response: OK
07-23-2012 23:56:23.312 - 921600,8,N,1, ctsfl=1, rtsctl=2
07-23-2012 23:56:23.328 - Initializing modem.
07-23-2012 23:56:23.343 - Send: AT<cr>
07-23-2012 23:56:23.343 - Recv: <cr><lf>OK<cr><lf>
07-23-2012 23:56:23.343 - Interpreted response: OK
07-23-2012 23:56:23.343 - Send: AT&FE0V1X1&D2&C1S0=0<cr>
07-23-2012 23:56:23.375 - Recv: <cr><lf>OK<cr><lf>
07-23-2012 23:56:23.375 - Interpreted response: OK
07-23-2012 23:56:23.390 - Send: AT<cr>
07-23-2012 23:56:23.390 - Recv: <cr><lf>OK<cr><lf>
07-23-2012 23:56:23.390 - Interpreted response: OK
07-23-2012 23:56:23.390 - Passthrough On
07-23-2012 23:56:31.281 - Passthrough Off
07-23-2012 23:56:31.281 - 460800,8,N,1, ctsfl=0, rtsctl=1
07-23-2012 23:56:31.296 - Initializing modem.
07-23-2012 23:56:31.296 - Send: AT<cr>
07-23-2012 23:56:31.312 - Recv: AT<cr>
07-23-2012 23:56:31.312 - Command Echo
07-23-2012 23:56:31.312 - Recv: <cr><lf>OK<cr><lf>
07-23-2012 23:56:31.312 - Interpreted response: OK
07-23-2012 23:56:31.312 - Send: AT&FE0V1X1&D2&C1S0=0<cr>
07-23-2012 23:56:31.312 - Recv: AT&FE0V1X1&D2&C1S0=0<cr>
07-23-2012 23:56:31.312 - Command Echo
07-23-2012 23:56:31.359 - Recv: <cr><lf>OK<cr><lf>
07-23-2012 23:56:31.359 - Interpreted response: OK
07-23-2012 23:56:31.375 - Send: AT<cr>
07-23-2012 23:56:31.375 - Recv: <cr><lf>OK<cr><lf>
07-23-2012 23:56:31.375 - Interpreted response: OK
07-23-2012 23:56:31.375 - Dialing.
07-23-2012 23:56:31.375 - Send: ATDT####<cr>
07-23-2012 23:56:33.000 - Recv: <cr><lf>CONNECT 153600<cr><lf>
07-23-2012 23:56:33.000 - Interpreted response: Connect
07-23-2012 23:56:33.000 - Receive Connect but CD was low, Waiting for
signal to go high
07-23-2012 23:56:33.015 - After waiting 20ms CD is still low.
07-23-2012 23:56:33.046 - CD has been raised
07-23-2012 23:56:33.046 - Connection established at 153600bps.
07-23-2012 23:56:33.046 - Error-control off or unknown.
07-23-2012 23:56:33.046 - Data compression off or unknown.
07-23-2012 23:57:03.046 - Read: Total: 7732, Per/Sec: 255, Written:
Total: 4478, Per/Sec: 148
And finally some lines from /var/log/messages :
Jul 23 22:36:15 bourne syslogd: kernel boot file is /boot/kernel/kernel
Jul 23 22:36:15 bourne kernel: Copyright (c) 1992-2011 The FreeBSD Project.
Jul 23 22:36:15 bourne kernel: Copyright (c) 1979, 1980, 1983, 1986,
1988, 1989, 1991, 1992, 1993, 1994
Jul 23 22:36:15 bourne kernel: The Regents of the University of
California. All rights reserved.
Jul 23 22:36:15 bourne kernel: FreeBSD is a registered trademark of The
FreeBSD Foundation.
Jul 23 22:36:15 bourne kernel: FreeBSD 8.2-RELEASE #0: Thu Feb 17
02:41:51 UTC 2011
Jul 23 22:36:15 bourne kernel:
r...@mason.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC amd64
Jul 23 22:36:15 bourne kernel: Timecounter "i8254" frequency 1193182 Hz
quality 0
Jul 23 22:36:15 bourne kernel: CPU: AMD Phenom(tm) 9650 Quad-Core
Processor (2304.92-MHz K8-class CPU)
Jul 23 22:36:15 bourne kernel: Origin = "AuthenticAMD" Id = 0x100f23
Family = 10 Model = 2 Stepping = 3
Jul 23 22:36:15 bourne kernel:
Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
Jul 23 22:36:15 bourne kernel: Features2=0x802009<SSE3,MON,CX16,POPCNT>
Jul 23 22:36:15 bourne kernel: AMD
Features=0xee500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM,3DNow!+,3DNow!>
Jul 23 22:36:15 bourne kernel: AMD
Features2=0x7ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS>
Jul 23 22:36:15 bourne kernel: TSC: P-state invariant
Jul 23 22:36:15 bourne kernel: real memory = 4294967296 (4096 MB)
Jul 23 22:36:15 bourne kernel: avail memory = 3833356288 (3655 MB)
Jul 23 22:36:15 bourne kernel: ACPI APIC Table: <GBT GBTUACPI>
Jul 23 22:36:15 bourne kernel: FreeBSD/SMP: Multiprocessor System
Detected: 4 CPUs
Jul 23 22:36:15 bourne kernel: FreeBSD/SMP: 1 package(s) x 4 core(s)
Jul 23 22:36:15 bourne kernel: cpu0 (BSP): APIC ID: 0
Jul 23 22:36:15 bourne kernel: cpu1 (AP): APIC ID: 1
Jul 23 22:36:15 bourne kernel: cpu2 (AP): APIC ID: 2
Jul 23 22:36:15 bourne kernel: cpu3 (AP): APIC ID: 3
Jul 23 22:36:15 bourne kernel: ioapic0: Changing APIC ID to 2
Jul 23 22:36:15 bourne kernel: ioapic0 <Version 2.1> irqs 0-23 on
motherboard
Jul 23 22:36:15 bourne kernel: kbd1 at kbdmux0
Jul 23 22:36:15 bourne kernel: acpi0: <GBT GBTUACPI> on motherboard
Jul 23 22:36:15 bourne kernel: acpi0: [ITHREAD]
Jul 23 22:36:15 bourne kernel: acpi0: Power Button (fixed)
Jul 23 22:36:15 bourne kernel: acpi0: reservation of 0, a0000 (3) failed
Jul 23 22:36:15 bourne kernel: acpi0: reservation of 100000, bfde0000
(3) failed
Jul 23 22:36:15 bourne kernel: Timecounter "ACPI-fast" frequency 3579545
Hz quality 1000
Jul 23 22:36:15 bourne kernel: acpi_timer0: <32-bit timer at
3.579545MHz> port 0x4008-0x400b on acpi0
Jul 23 22:36:15 bourne kernel: cpu0: <ACPI CPU> on acpi0
Jul 23 22:36:15 bourne kernel: cpu1: <ACPI CPU> on acpi0
Jul 23 22:36:15 bourne kernel: cpu2: <ACPI CPU> on acpi0
Jul 23 22:36:15 bourne kernel: cpu3: <ACPI CPU> on acpi0
Jul 23 22:36:15 bourne kernel: acpi_button0: <Power Button> on acpi0
Jul 23 22:36:15 bourne kernel: pcib0: <ACPI Host-PCI bridge> port
0xcf8-0xcff on acpi0
Jul 23 22:36:15 bourne kernel: pci0: <ACPI PCI bus> on pcib0
Jul 23 22:36:15 bourne kernel: pcib1: <ACPI PCI-PCI bridge> at device
1.0 on pci0
Jul 23 22:36:15 bourne kernel: pci1: <ACPI PCI bus> on pcib1
Jul 23 22:36:15 bourne kernel: vgapci0: <VGA-compatible display> port
0xee00-0xeeff mem
0xd0000000-0xdfffffff,0xfdfe0000-0xfdfeffff,0xfde00000-0xfdefffff irq 18
at device 5.0 on pci1
Jul 23 22:36:15 bourne kernel: hdac0: <ATI RS780 High Definition Audio
Controller> mem 0xfdffc000-0xfdffffff irq 19 at device 5.1 on pci1
Jul 23 22:36:15 bourne kernel: hdac0: HDA Driver Revision: 20100226_0142
Jul 23 22:36:15 bourne kernel: hdac0: [ITHREAD]
Jul 23 22:36:15 bourne kernel: pcib2: <ACPI PCI-PCI bridge> irq 18 at
device 10.0 on pci0
Jul 23 22:36:15 bourne kernel: pci2: <ACPI PCI bus> on pcib2
Jul 23 22:36:15 bourne kernel: re0: <RealTek 8168/8111 B/C/CP/D/DP/E
PCIe Gigabit Ethernet> port 0xde00-0xdeff mem
0xfdaff000-0xfdafffff,0xfdae0000-0xfdaeffff irq 18 at device 0.0 on pci2
Jul 23 22:36:15 bourne kernel: re0: Using 1 MSI messages
Jul 23 22:36:15 bourne kernel: re0: Chip rev. 0x3c000000
Jul 23 22:36:15 bourne kernel: re0: MAC rev. 0x00400000
Jul 23 22:36:15 bourne kernel: miibus0: <MII bus> on re0
Jul 23 22:36:15 bourne kernel: rgephy0: <RTL8169S/8110S/8211B media
interface> PHY 1 on miibus0
Jul 23 22:36:15 bourne kernel: rgephy0: 10baseT, 10baseT-FDX,
10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow,
1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master,
1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
Jul 23 22:36:15 bourne kernel: re0: Ethernet address: 00:24:1d:22:5c:27
Jul 23 22:36:15 bourne kernel: re0: [FILTER]
Jul 23 22:36:15 bourne kernel: atapci0: <ATI IXP700/800 SATA300
controller> port
0xff00-0xff07,0xfe00-0xfe03,0xfd00-0xfd07,0xfc00-0xfc03,0xfb00-0xfb0f
mem 0xfe02f000-0xfe02f3ff irq 22 at device 17.0 on pci0
Jul 23 22:36:15 bourne kernel: atapci0: [ITHREAD]
Jul 23 22:36:15 bourne kernel: atapci0: AHCI v1.10 controller with 4
3Gbps ports, PM supported
Jul 23 22:36:15 bourne kernel: ata2: <ATA channel 0> on atapci0
Jul 23 22:36:15 bourne kernel: ata2: port is not ready (timeout 0ms) tfd
= 00000180
Jul 23 22:36:15 bourne kernel: ata2: software reset clear timeout
Jul 23 22:36:15 bourne kernel: ata2: [ITHREAD]
Jul 23 22:36:15 bourne kernel: ata3: <ATA channel 1> on atapci0
Jul 23 22:36:15 bourne kernel: ata3: [ITHREAD]
Jul 23 22:36:15 bourne kernel: ata4: <ATA channel 2> on atapci0
Jul 23 22:36:15 bourne kernel: ata4: port is not ready (timeout 0ms) tfd
= 000001d0
Jul 23 22:36:15 bourne kernel: ata4: software reset clear timeout
Jul 23 22:36:15 bourne kernel: ata4: [ITHREAD]
Jul 23 22:36:15 bourne kernel: ata5: <ATA channel 3> on atapci0
Jul 23 22:36:15 bourne kernel: ata5: [ITHREAD]
Jul 23 22:36:15 bourne kernel: ohci0: <OHCI (generic) USB controller>
mem 0xfe02e000-0xfe02efff irq 16 at device 18.0 on pci0
Jul 23 22:36:15 bourne kernel: ohci0: [ITHREAD]
Jul 23 22:36:15 bourne kernel: usbus0: <OHCI (generic) USB controller>
on ohci0
Jul 23 22:36:15 bourne kernel: ohci1: <OHCI (generic) USB controller>
mem 0xfe02d000-0xfe02dfff irq 16 at device 18.1 on pci0
Jul 23 22:36:15 bourne kernel: ohci1: [ITHREAD]
Jul 23 22:36:15 bourne kernel: usbus1: <OHCI (generic) USB controller>
on ohci1
Jul 23 22:36:15 bourne kernel: ehci0: <EHCI (generic) USB 2.0
controller> mem 0xfe02c000-0xfe02c0ff irq 17 at device 18.2 on pci0
Jul 23 22:36:15 bourne kernel: ehci0: [ITHREAD]
Jul 23 22:36:15 bourne kernel: ehci0: AMD SB600/700 quirk applied
Jul 23 22:36:15 bourne kernel: usbus2: EHCI version 1.0
Jul 23 22:36:15 bourne kernel: usbus2: <EHCI (generic) USB 2.0
controller> on ehci0
Jul 23 22:36:15 bourne kernel: ohci2: <OHCI (generic) USB controller>
mem 0xfe02b000-0xfe02bfff irq 18 at device 19.0 on pci0
Jul 23 22:36:15 bourne kernel: ohci2: [ITHREAD]
Jul 23 22:36:15 bourne kernel: usbus3: <OHCI (generic) USB controller>
on ohci2
Jul 23 22:36:15 bourne kernel: ohci3: <OHCI (generic) USB controller>
mem 0xfe02a000-0xfe02afff irq 18 at device 19.1 on pci0
Jul 23 22:36:15 bourne kernel: ohci3: [ITHREAD]
Jul 23 22:36:15 bourne kernel: usbus4: <OHCI (generic) USB controller>
on ohci3
Jul 23 22:36:15 bourne kernel: ehci1: <EHCI (generic) USB 2.0
controller> mem 0xfe029000-0xfe0290ff irq 19 at device 19.2 on pci0
Jul 23 22:36:15 bourne kernel: ehci1: [ITHREAD]
Jul 23 22:36:15 bourne kernel: ehci1: AMD SB600/700 quirk applied
Jul 23 22:36:15 bourne kernel: usbus5: EHCI version 1.0
Jul 23 22:36:15 bourne kernel: usbus5: <EHCI (generic) USB 2.0
controller> on ehci1
Jul 23 22:36:15 bourne kernel: pci0: <serial bus, SMBus> at device 20.0
(no driver attached)
Jul 23 22:36:15 bourne kernel: atapci1: <ATI IXP700/800 UDMA133
controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfa00-0xfa0f at
device 20.1 on pci0
Jul 23 22:36:15 bourne kernel: ata0: <ATA channel 0> on atapci1
Jul 23 22:36:15 bourne kernel: ata0: [ITHREAD]
Jul 23 22:36:15 bourne kernel: ata1: <ATA channel 1> on atapci1
Jul 23 22:36:15 bourne kernel: ata1: [ITHREAD]
Jul 23 22:36:15 bourne kernel: hdac1: <ATI SB600 High Definition Audio
Controller> mem 0xfe024000-0xfe027fff irq 16 at device 20.2 on pci0
Jul 23 22:36:15 bourne kernel: hdac1: HDA Driver Revision: 20100226_0142
Jul 23 22:36:15 bourne kernel: hdac1: [ITHREAD]
Jul 23 22:36:15 bourne kernel: isab0: <PCI-ISA bridge> at device 20.3 on
pci0
Jul 23 22:36:15 bourne kernel: isa0: <ISA bus> on isab0
Jul 23 22:36:15 bourne kernel: pcib3: <ACPI PCI-PCI bridge> at device
20.4 on pci0
Jul 23 22:36:15 bourne kernel: pci3: <ACPI PCI bus> on pcib3
Jul 23 22:36:15 bourne kernel: fwohci0: <Texas Instruments TSB43AB23>
mem 0xfdcff000-0xfdcff7ff,0xfdcf8000-0xfdcfbfff irq 22 at device 14.0 on
pci3
Jul 23 22:36:15 bourne kernel: fwohci0: [ITHREAD]
Jul 23 22:36:15 bourne kernel: fwohci0: OHCI version 1.10 (ROM=0)
Jul 23 22:36:15 bourne kernel: fwohci0: No. of Isochronous channels is 4.
Jul 23 22:36:15 bourne kernel: fwohci0: EUI64 00:ed:04:7d:00:00:1f:d0
Jul 23 22:36:15 bourne kernel: fwohci0: Phy 1394a available S400, 3 ports.
Jul 23 22:36:15 bourne kernel: fwohci0: Link S400, max_rec 2048 bytes.
Jul 23 22:36:15 bourne kernel: firewire0: <IEEE1394(FireWire) bus> on
fwohci0
Jul 23 22:36:15 bourne kernel: fwe0: <Ethernet over FireWire> on firewire0
Jul 23 22:36:15 bourne kernel: if_fwe0: Fake Ethernet address:
02:ed:04:00:1f:d0
Jul 23 22:36:15 bourne kernel: fwe0: Ethernet address: 02:ed:04:00:1f:d0
Jul 23 22:36:15 bourne kernel: fwip0: <IP over FireWire> on firewire0
Jul 23 22:36:15 bourne kernel: fwip0: Firewire address:
00:ed:04:7d:00:00:1f:d0 @ 0xfffe00000000, S400, maxrec 2048
Jul 23 22:36:15 bourne kernel: dcons_crom0: <dcons configuration ROM> on
firewire0
Jul 23 22:36:15 bourne kernel: dcons_crom0: bus_addr 0x1b3c000
Jul 23 22:36:15 bourne kernel: fwohci0: Initiate bus reset
Jul 23 22:36:15 bourne kernel: fwohci0: fwohci_intr_core: BUS reset
Jul 23 22:36:15 bourne kernel: fwohci0: fwohci_intr_core:
node_id=0x00000000, SelfID Count=1, CYCLEMASTER mode
Jul 23 22:36:15 bourne kernel: ohci4: <OHCI (generic) USB controller>
mem 0xfe028000-0xfe028fff irq 18 at device 20.5 on pci0
Jul 23 22:36:15 bourne kernel: ohci4: [ITHREAD]
Jul 23 22:36:15 bourne kernel: usbus6: <OHCI (generic) USB controller>
on ohci4
Jul 23 22:36:15 bourne kernel: uart0: <16550 or compatible> port
0x3f8-0x3ff irq 4 flags 0x10 on acpi0
Jul 23 22:36:15 bourne kernel: uart0: [FILTER]
Jul 23 22:36:15 bourne kernel: ppc0: <Parallel port> port
0x378-0x37f,0x778-0x77b irq 7 drq 3 on acpi0
Jul 23 22:36:15 bourne kernel: ppc0: SMC-like chipset
(ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
Jul 23 22:36:15 bourne kernel: ppc0: FIFO with 16/16/16 bytes threshold
Jul 23 22:36:15 bourne kernel: ppc0: [ITHREAD]
Jul 23 22:36:15 bourne kernel: ppbus0: <Parallel port bus> on ppc0
Jul 23 22:36:15 bourne kernel: plip0: <PLIP network interface> on ppbus0
Jul 23 22:36:15 bourne kernel: plip0: [ITHREAD]
Jul 23 22:36:15 bourne kernel: lpt0: <Printer> on ppbus0
Jul 23 22:36:15 bourne kernel: lpt0: [ITHREAD]
Jul 23 22:36:15 bourne kernel: lpt0: Interrupt-driven port
Jul 23 22:36:15 bourne kernel: ppi0: <Parallel I/O> on ppbus0
Jul 23 22:36:15 bourne kernel: atkbdc0: <Keyboard controller (i8042)>
port 0x60,0x64 irq 1 on acpi0
Jul 23 22:36:15 bourne kernel: atkbd0: <AT Keyboard> irq 1 on atkbdc0
Jul 23 22:36:15 bourne kernel: kbd0 at atkbd0
Jul 23 22:36:15 bourne kernel: atkbd0: [GIANT-LOCKED]
Jul 23 22:36:15 bourne kernel: atkbd0: [ITHREAD]
Jul 23 22:36:15 bourne kernel: psm0: <PS/2 Mouse> irq 12 on atkbdc0
Jul 23 22:36:15 bourne kernel: psm0: [GIANT-LOCKED]
Jul 23 22:36:15 bourne kernel: psm0: [ITHREAD]
Jul 23 22:36:15 bourne kernel: psm0: model IntelliMouse Explorer, device
ID 4
Jul 23 22:36:15 bourne kernel: atrtc0: <AT realtime clock> port
0x70-0x73 irq 8 on acpi0
Jul 23 22:36:15 bourne kernel: sc0: <System console> at flags 0x100 on isa0
Jul 23 22:36:15 bourne kernel: sc0: VGA <16 virtual consoles, flags=0x300>
Jul 23 22:36:15 bourne kernel: vga0: <Generic ISA VGA> at port
0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Jul 23 22:36:15 bourne kernel: hwpstate0: <Cool`n'Quiet 2.0> on cpu0
Jul 23 22:36:15 bourne kernel: Timecounters tick every 1.000 msec
Jul 23 22:36:15 bourne kernel: firewire0: 1 nodes, maxhop <= 0 cable IRM
irm(0) (me)
Jul 23 22:36:15 bourne kernel: firewire0: bus manager 0
Jul 23 22:36:15 bourne kernel: usbus0: 12Mbps Full Speed USB v1.0
Jul 23 22:36:15 bourne kernel: usbus1: 12Mbps Full Speed USB v1.0
Jul 23 22:36:15 bourne kernel: usbus2: 480Mbps High Speed USB v2.0
Jul 23 22:36:15 bourne kernel: usbus3: 12Mbps Full Speed USB v1.0
Jul 23 22:36:15 bourne kernel: usbus4: 12Mbps Full Speed USB v1.0
Jul 23 22:36:15 bourne kernel: usbus5: 480Mbps High Speed USB v2.0
Jul 23 22:36:15 bourne kernel: usbus6: 12Mbps Full Speed USB v1.0
Jul 23 22:36:15 bourne kernel: ugen0.1: <ATI> at usbus0
Jul 23 22:36:15 bourne kernel: uhub0: <ATI OHCI root HUB, class 9/0, rev
1.00/1.00, addr 1> on usbus0
Jul 23 22:36:15 bourne kernel: ugen1.1: <ATI> at usbus1
Jul 23 22:36:15 bourne kernel: uhub1: <ATI OHCI root HUB, class 9/0, rev
1.00/1.00, addr 1> on usbus1
Jul 23 22:36:15 bourne kernel: ugen2.1: <ATI> at usbus2
Jul 23 22:36:15 bourne kernel: uhub2: <ATI EHCI root HUB, class 9/0, rev
2.00/1.00, addr 1> on usbus2
Jul 23 22:36:15 bourne kernel: ugen3.1: <ATI> at usbus3
Jul 23 22:36:15 bourne kernel: uhub3: <ATI OHCI root HUB, class 9/0, rev
1.00/1.00, addr 1> on usbus3
Jul 23 22:36:15 bourne kernel: ugen4.1: <ATI> at usbus4
Jul 23 22:36:15 bourne kernel: uhub4: <ATI OHCI root HUB, class 9/0, rev
1.00/1.00, addr 1> on usbus4
Jul 23 22:36:15 bourne kernel: ugen5.1: <ATI> at usbus5
Jul 23 22:36:15 bourne kernel: uhub5: <ATI EHCI root HUB, class 9/0, rev
2.00/1.00, addr 1> on usbus5
Jul 23 22:36:15 bourne kernel: ugen6.1: <ATI> at usbus6
Jul 23 22:36:15 bourne kernel: uhub6: <ATI OHCI root HUB, class 9/0, rev
1.00/1.00, addr 1> on usbus6
Jul 23 22:36:15 bourne kernel: acd0: DVDROM <HL-DT-STDVD-ROM
GDR8163B/0L23> at ata0-master UDMA33
Jul 23 22:36:15 bourne kernel: acd1: DVDR <Optiarc DVD RW AD-7240S/1.02>
at ata2-master UDMA100 SATA 1.5Gb/s
Jul 23 22:36:15 bourne kernel: ad8: 305244MB <WDC WD3200AAJS-00L7A0
01.03E01> at ata4-master UDMA100 SATA 3Gb/s
Jul 23 22:36:15 bourne kernel: hdac0: HDA Codec #0: ATI RS690/780 HDMI
Jul 23 22:36:15 bourne kernel: pcm0: <HDA ATI RS690/780 HDMI PCM #0
HDMI> at cad 0 nid 1 on hdac0
Jul 23 22:36:15 bourne kernel: hdac1: HDA Codec #0: Realtek ALC885
Jul 23 22:36:15 bourne kernel: pcm1: <HDA Realtek ALC885 PCM #0 Analog>
at cad 0 nid 1 on hdac1
Jul 23 22:36:15 bourne kernel: pcm2: <HDA Realtek ALC885 PCM #1 Analog>
at cad 0 nid 1 on hdac1
Jul 23 22:36:15 bourne kernel: pcm3: <HDA Realtek ALC885 PCM #2 Digital>
at cad 0 nid 1 on hdac1
Jul 23 22:36:15 bourne kernel: SMP: AP CPU #1 Launched!
Jul 23 22:36:15 bourne kernel: SMP: AP CPU #3 Launched!
Jul 23 22:36:15 bourne kernel: SMP: AP CPU #2 Launched!
Jul 23 22:36:15 bourne kernel: uhub6: 2 ports with 2 removable, self powered
Jul 23 22:36:15 bourne kernel: uhub0: 3 ports with 3 removable, self powered
Jul 23 22:36:15 bourne kernel: uhub1: 3 ports with 3 removable, self powered
Jul 23 22:36:15 bourne kernel: uhub3: 3 ports with 3 removable, self powered
Jul 23 22:36:15 bourne kernel: uhub4: 3 ports with 3 removable, self powered
Jul 23 22:36:15 bourne kernel: Root mount waiting for: usbus5 usbus2
Jul 23 22:36:15 bourne kernel: Root mount waiting for: usbus5 usbus2
Jul 23 22:36:15 bourne kernel: uhub2: 6 ports with 6 removable, self powered
Jul 23 22:36:15 bourne kernel: uhub5: 6 ports with 6 removable, self powered
Jul 23 22:36:15 bourne kernel: Root mount waiting for: usbus2
Jul 23 22:36:15 bourne kernel: ugen0.2: <American Power Conversion> at
usbus0
Jul 23 22:36:15 bourne kernel: ugen1.2: <HUAWEI TECHNOLOGIES> at usbus1
Jul 23 22:36:15 bourne kernel: umass0: <HUAWEI TECHNOLOGIES HUAWEI
Mobile, class 0/0, rev 1.10/0.00, addr 2> on usbus1
Jul 23 22:36:15 bourne kernel: umass0: SCSI over Bulk-Only; quirks = 0x0000
Jul 23 22:36:15 bourne kernel: ugen2.2: <vendor 0x05e3> at usbus2
Jul 23 22:36:15 bourne kernel: uhub7: <vendor 0x05e3 USB2.0 Hub, class
9/0, rev 2.00/77.60, addr 2> on usbus2
Jul 23 22:36:15 bourne kernel: Root mount waiting for: usbus2
Jul 23 22:36:15 bourne kernel: uhub7: 4 ports with 4 removable, self powered
Jul 23 22:36:15 bourne kernel: Trying to mount root from ufs:/dev/ad8s2a
Jul 23 22:36:15 bourne kernel: umass0:0:0:-1: Attached to scbus0
Jul 23 22:36:15 bourne kernel: cd0 at umass-sim0 bus 0 scbus0 target 0 lun 0
Jul 23 22:36:15 bourne kernel: cd0: <HUAWEI Mass Storage 2.31> Removable
CD-ROM SCSI-0 device
Jul 23 22:36:15 bourne kernel: cd0: 1.000MB/s transfers
Jul 23 22:36:15 bourne kernel: cd0: cd present [52352 x 2048 byte records]
Jul 23 22:36:15 bourne kernel: (probe0:umass-sim0:0:0:1): TEST UNIT
READY. CDB: 0 20 0 0 0 0
Jul 23 22:36:15 bourne kernel: (probe0:umass-sim0:0:0:1): CAM status:
SCSI Status Error
Jul 23 22:36:15 bourne kernel: (probe0:umass-sim0:0:0:1): SCSI status:
Check Condition
Jul 23 22:36:15 bourne kernel: (probe0:umass-sim0:0:0:1): SCSI sense:
NOT READY asc:3a,0 (Medium not present)
Jul 23 22:36:15 bourne kernel: da0 at umass-sim0 bus 0 scbus0 target 0 lun 1
Jul 23 22:36:15 bourne kernel: da0: <HUAWEI SD Storage 2.31> Removable
Direct Access SCSI-2 device
Jul 23 22:36:15 bourne kernel: da0: 1.000MB/s transfers
Jul 23 22:36:15 bourne kernel: da0: Attempt to query device size failed:
NOT READY, Medium not present
Jul 23 22:36:16 bourne kernel: u3g0: <Data Interface> on usbus1
Jul 23 22:36:16 bourne kernel: u3g0: Found 3 ports.
Jul 23 22:36:16 bourne root: Unknown USB device: vendor 0x051d product
0x0002 bus uhub0
Jul 23 22:36:17 bourne root: Unknown USB device: vendor 0x051d product
0x0002 bus uhub0
Jul 23 22:36:19 bourne apcupsd[1165]: apcupsd 3.14.8 (16 January 2010)
freebsd startup succeeded
Jul 23 22:36:19 bourne kernel: tun0: link state changed to UP
Jul 23 22:36:19 bourne lpd[1227]: lpd startup: logging=0
Jul 23 22:36:19 bourne kernel: fuse4bsd: version 0.3.9-pre1, FUSE ABI 7.8
Jul 23 22:36:20 bourne apcupsd[1165]: Power failure.
Jul 23 22:36:21 bourne avahi-daemon[1471]: WARNING: No NSS support for
mDNS detected, consider installing nss-mdns!
Jul 23 22:36:25 bourne apcupsd[1165]: Running on UPS batteries.
Jul 23 22:36:27 bourne apcupsd[1165]: Mains returned. No longer on UPS
batteries.
Jul 23 22:36:27 bourne apcupsd[1165]: Power is back. UPS running on mains.
Jul 23 22:36:37 bourne login: ROOT LOGIN (root) ON ttyv0
Jul 23 22:36:49 bourne ppp[1217]: tun0: Warning: Chat script failed
Jul 23 22:37:20 bourne ppp[1217]: tun0: Warning: Chat script failed
Any help in pointing out what error I am making will be greatly
appreciated. Remember, I cannot install any new port since my FreeBSD
box does not yet connect to the internet.
Thanks &
--
Regards,
Manish Jain
+91-99620-10329
_______________________________________________
freebsd-questions@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to "freebsd-questions-unsubscr...@freebsd.org"
